帅哥
发表于 2009-4-29 13:10:46
21A.605 Data requirementsThe applicant shall submit the following documents, to the Agency:(a) A statement of compliance certifying that the applicant has met the requirements of this Subpart.(b) A Declaration of Design and Performance (DDP).(c) One copy of the technical data required in the applicable ETSO.(d) The exposition (or a reference to the exposition) referred to in 21A.143 for the purpose of obtaining an appropriateproduction organisation approval under Subpart G or the manual (or a reference to the manual) referred to in21A.125(b) for the purpose of manufacturing under Subpart F without production organisation approval.(e) For an APU, the handbook (or a reference to the handbook) referred to in 21A.243 for the purpose of obtaining anappropriate design organisation approval under Subpart J.(f) for all other articles, the procedures referred to in 21A.602B(b)(2).21A.606 Issue of ETSO authorisationThe applicant shall be entitled to have an ETSO authorisation issued by the Agency after:(a) demonstrating its capability in accordance with 21A.602B; and(b) demonstrating that the article complies with the technical conditions of the applicable ETSO, and submitting thecorresponding statement of compliance.(c) showing that it is able to comply with 21A.3(b) and (c).21A.607 ETSO authorisation privilegesThe holder of an ETSO authorisation is entitled to produce and to mark the article with the appropriate ETSO marking.27.9.2003 EN Official Journal of the European Union L 243/4721A.608 Declaration of Design and Performance (DDP)(a) The DDP shall contain at least the following information:1. Information corresponding to 21A.31(a) and (b), identifying the article and its design and testing standard.2. The rated performance of the article, where appropriate, either directly or by reference to other supplementarydocuments.3. A statement of compliance certifying that the article has met the appropriate ETSO.4. Reference to relevant test reports.5. Reference to the appropriate Maintenance, Overhaul and Repair Manuals.6. The levels of compliance, where various levels of compliance are allowed by the ETSO.7. List of deviations accepted in accordance with 21A.610.(b) The DDP shall be endorsed with the date and signature of the holder of the ETSO authorisation, or its authorisedrepresentative.21A.609 Obligations of holders of ETSO authorisationsThe holder of an ETSO authorisation under this Subpart shall:(a) Manufacture each article in accordance with Subpart G or Subpart F that ensures that each completed articleconforms to its design data and is safe for installation;(b) Prepare and maintain, for each model of each article for which an ETSO authorisation has been issued, a current fileof complete technical data and records in accordance with 21A.613;(c) Prepare, maintain and update master copies of all manuals required by the applicable airworthiness specifications forthe article;(d) Make available to users of the article and to the Agency on request those maintenance, overhaul and repair manualsnecessary for the usage and maintenance of the article, and changes to those manuals;(e) Mark each article in accordance with 21A.807; and(f) Comply with 21A.3(b), (c), 21A.3B and 21A.4.(g) Continue to meet the qualification requirements of 21A.602B.
帅哥
发表于 2009-4-29 13:10:59
21A.610 Approval for deviation(a) Each manufacturer who requests approval to deviate from any performance standard of an ETSO shall demonstratethat the standards from which a deviation is requested are compensated for by factors or design features providingan equivalent level of safety.(b) The request for approval to deviate, together with all pertinent data, shall be submitted to the Agency.21A.611 Design changes(a) The holder of the ETSO authorisation may make minor design changes (any change other than a major change)without further authorisation by the Agency. In this case, the changed article keeps the original model number (partnumber changes or amendments shall be used to identify minor changes) and the holder shall forward to the Agencyany revised data that are necessary for compliance with 21A.603(b).(b) Any design change by the holder of the ETSO authorisation that is extensive enough to require a substantiallycomplete investigation to determine compliance with an ETSO is a major change. Before making such a change, theholder shall assign a new type or model designation to the article and apply for a new authorisation under 21A.603.(c) No design change by any natural or legal person other than the holder of the ETSO authorisation who submittedthe statement of compliance for the article is eligible for approval under this Subpart O unless the person seekingthe approval applies under 21A.603 for a separate ETSO authorisation.L 243/48 EN Official Journal of the European Union 27.9.200321A.613 Record keepingFurther to the record keeping requirements appropriate to or associated with the quality system, all relevant design information,drawings and test reports, including inspection records for the article tested, shall be held at the disposal of theAgency and shall be retained in order to provide the information necessary to ensure the continued airworthiness of thearticle and of the type-certificated product in which it is fitted.21A.615 Inspection by the AgencyUpon a request of the Agency, each applicant for, or holder of an ETSO authorisation for an article shall allow theAgency to:(a) Witness any tests.(b) Inspect the technical data files on that article.21A.619 Duration and continued validity(a) An ETSO authorisation shall be issued for an unlimited duration. It shall remain valid unless:1. The conditions required when ETSO authorisation was granted are no longer being observed; or2. The obligations of the holder specified in 21A.609 are no longer being discharged; or3. The article has proved to give rise to unacceptable hazards in service; or4. the authorisation has been surrendered or revoked under the applicable administrative procedures established bythe Agency.(b) Upon surrender or revocation, the certificate shall be returned to the Agency.21A.621 TransferabilityExcept for a change in ownership of the holder, which shall be regarded as a change of significance, and shall thereforecomply with 21A.147 and 21A.247 as applicable, an ETSO authorisation issued under this Part is not transferable.(SUBPART P — NOT APPLICABLE)SUBPART Q — IDENTIFICATION OF PRODUCTS, PARTS AND APPLIANCES21A.801 Identification of products(a) The identification of products shall include the following information:1. Manufacturer's name.2. Product designation.3. Manufacturer's Serial number.4. Any other information the Agency finds appropriate.(b) Any natural or legal person that manufactures an aircraft or engine under Subpart G or Subpart F shall identify thataircraft or engine by means of a fireproof plate that has the information specified in paragraph (a) marked on it byetching, stamping, engraving, or other approved method of fireproof marking. The identification plate shall besecured in such a manner that it is accessible and legible, and will not likely be defaced or removed during normalservice, or lost or destroyed in an accident.(c) Any natural or legal person that manufactures a propeller, propeller blade, or propeller hub under Subpart G orSubpart F shall identify it by means of a plate, stamping, engraving, etching or other approved method of fireproofidentification that is placed on it on a non-critical surface, contains the information specified in paragraph (a), andwill not likely be defaced or removed during normal service or lost or destroyed in an accident.(d) For manned free balloons, the identification plate prescribed in paragraph (b) shall be secured to the balloonenvelope and shall be located, if practicable, where it is legible to the operator when the balloon is inflated. In addition,the basket and any heater assembly shall be permanently and legibly marked with the manufacturer's name,part number, or equivalent, and serial number, or equivalent.27.9.2003 EN Official Journal of the European Union L 243/49
帅哥
发表于 2009-4-29 13:11:11
21A.803 Handling of identification data(a) No person shall remove, change, or place identification information referred to in 21A.801(a) on any aircraft,engine, propeller, propeller blade, or propeller hub, or in 21A.807(a) on an APU, without the approval of theAgency.(b) No person shall remove or install any identification plate referred to in 21A.801, or in 21A.807 for an APU, withoutthe approval of the Agency.(c) By way of derogation from paragraphs (a) and (b), any natural or legal person performing maintenance work underthe applicable associated implementing rules may, in accordance with methods, techniques and practices establishedby the Agency:1. Remove, change, or place the identification information referred to in 21A.801(a) on any aircraft, engine,propeller, propeller blade, or propeller hub, or in 21A.807(a) on an APU; or2. Remove an identification plate referred to in 21A.801, or 21A.807 for an APU, when necessary during maintenanceoperations.(d) No person shall install an identification plate removed in accordance with subparagraph (c)(2) on any aircraft,engine, propeller, propeller blade, or propeller hub other than the one from which it was removed.21A.804 Identification of parts and appliances(a) Each manufacturer of a part or appliance shall permanently and legibly mark the part or appliance with:1. a name, trademark, or symbol identifying the manufacturer; and2. the part number, as defined in the applicable design data; and3. the letters EPA (European Part Approval) for parts or appliances produced in accordance with approved designdata not belonging to the type-certificate holder of the related product, except for ETSO articles.(b) By way of derogation from paragraph (a), if the Agency agrees that a part or appliance is too small or that it isotherwise impractical to mark a part or appliance with any of the information required by paragraph (a), theauthorised release document accompanying the part or appliance or its container shall include the information thatcould not be marked on the part.21A.805 Identification of critical partsIn addition to the requirement of 21A.804, each manufacturer of a part to be fitted on a type-certificated product whichhas been identified as a critical part shall permanently and legibly mark that part with a part number and a serialnumber.21A.807 Identification of ETSO articles(a) Each holder of an ETSO authorisation under Subpart O shall permanently and legibly mark each article with thefollowing information:1. The name and address of the manufacturer;2. The name, type, part number or model designation of the article;3. The serial number or the date of manufacture of the article or both; and4. The applicable ETSO number.(b) By way of derogation from paragraph (a), if the Agency agrees that a part is too small or that it is otherwise impracticalto mark a part with any of the information required by paragraph (a), the authorised release document accompanyingthe part or its container shall include the information that could not be marked on the part.(c) Each person who manufactures an APU under Subpart G or Subpart F shall identify that APU by means of a fireproofplate that has the information specified in paragraph (a) marked on it by etching, stamping, engraving, orother approved method of fireproof marking. The identification plate shall be secured in such a manner that it isaccessible and legible, and will not likely be defaced or removed during normal service, or lost or destroyed in anaccident.L 243/50 EN Official Journal of the European Union 27.9.2003SECTION BPROCEDURES FOR COMPETENT AUTHORITIESSUBPART A — GENERAL PROVISIONS21B.5 Scope(a) This Section establishes the procedure for the competent authority of the Member State when exercising its tasksand responsibilities concerned with the issuance, maintenance, amendment, suspension and revocation of certificates,approvals and authorisations referred to in this Part.(b) The Agency shall develop in accordance with Article 14 of the basic Regulation certification specifications andguidance material to assist Member States in the implementation of this Section.21B.20 Obligations of the competent authorityEach competent authority of the Member State is responsible for the implementation of Section A, Subparts F, G, H andI only for applicants, or holders, whose principal place of business is in its territory.
帅哥
发表于 2009-4-29 13:11:23
21B.25 Requirements for the organisation of the competent authority(a) General:The Member State shall designate a competent authority with allocated responsibilities for the implementation ofSection A, Subparts F, G, H and I with documented procedures, organisation structure and staff.(b) Resources:1. The number of staff shall be sufficient to perform the allocated tasks.2. The competent authority of the Member State shall appoint a manager, or managers, who are responsible for theexecution of the related task(s) within the authority, including the communication with the Agency and the othernational authorities as appropriate.(c) Qualification and training:All staff shall be appropriately qualified and have sufficient knowledge, experience and training to perform their allocatedtask.21B.30 Documented procedures(a) The competent authority of the Member State shall establish documented procedures to describe its organisation,means and methods to fulfil the requirements of this Part. The procedures shall be kept up to date and serve as thebasic working documents within that authority for all related activities.(b) A copy of the procedures and their amendments shall be available to the Agency.21B.35 Changes in organisation and procedures(a) The competent authority of the Member State shall notify any significant change in its organisation and documentedprocedures to the Agency.(b) The competent authority of the Member State shall update its documented procedures relating to any change toregulations in a timely manner to ensure effective implementation.21B.40 Resolution of disputes(a) The competent authority of the Member State shall establish a process for the resolution of disputes within its organisationdocumented procedures.(b) Where a dispute, which cannot be resolved, exists between the competent authorities of the Member States it is theresponsibility of the managers as defined in 21B.25(b)(2) to raise the issue with the Agency for mediation.27.9.2003 EN Official Journal of the European Union L 243/5121B.45 Reporting/coordination(a) The competent authority of the Member State shall ensure coordination as applicable with other related certification,investigation, approval or authorisation teams of that authority, other Member States and the Agency to ensure efficientexchange of information relevant for safety of the products, parts and appliances.(b) The competent authority of the Member State shall notify any difficulty in the implementation of this Part to theAgency.21B.55 Record keepingThe competent authority of the Member State shall keep, or maintain access to, the appropriate records related to thecertificates, approvals and authorisations it has granted in accordance with the respective national regulations, and forwhich responsibility is transferred to the Agency, as long as these records have not been transferred to the Agency.
帅哥
发表于 2009-4-29 13:11:37
21B.60 Airworthiness directivesWhen the a competent authority of a Member State receives an airworthiness directive from the competent authority ofa non-member State, that airworthiness directive shall be transferred to the Agency for dissemination in accordance withArticle 15 of the basic Regulation.SUBPART B — TYPE-CERTIFICATES AND RESTRICTED TYPE-CERTIFICATESAdministrative procedures established by the Agency shall apply.(SUBPART C — NOT APPLICABLE)SUBPART D — CHANGES TO TYPE-CERTIFICATES AND RESTRICTED TYPE-CERTIFICATESAdministrative procedures established by the Agency shall apply.SUBPART E — SUPPLEMENTAL TYPE-CERTIFICATESAdministrative procedures established by the Agency shall apply.SUBPART F — PRODUCTION WITHOUT PRODUCTION ORGANISATION APPROVAL21B.120 Investigation(a) The Competent Authority shall appoint an investigation team for each applicant for, or holder of, a letter of agreementto conduct all relevant tasks related to this letter of agreement, consisting of a team-leader to manage and leadthe investigation team and, if required, one or more team members. The team-leader reports to the manager responsiblefor the activity, as defined in 21B.25 (b)(2).(b) The Competent Authority shall perform sufficient investigation activities for an applicant for, or holder of, a letter ofagreement to justify recommendations for the issuance, maintenance, amendment, suspension or revocation of theletter of agreement.(c) The Competent Authority shall prepare procedures for the investigation of applicants for, or holders of, a letter ofagreement as part of the documented procedures covering at least the following elements:1. evaluation of applications received;2. determination of investigation team;3. investigation preparation and planning;4. evaluation of the documentation (manual, procedures, etc.);5. auditing and inspection;6. follow up of corrective actions; and7. recommendation for issuance, amendment, suspension or revocation of the letter of agreement.L 243/52 EN Official Journal of the European Union 27.9.200321B.130 Issue of letter of agreement(a) When satisfied that the manufacturer is in compliance with the applicable requirements of Section A, Subpart F, theCompetent Authority shall issue a letter of agreement to the showing of conformity of individual products, parts orappliances (EASA Form 65, see Appendix) without undue delay.(b) The letter of agreement shall contain the scope of the agreement, a termination date and, where applicable, theappropriate limitations relating to the authorisation.(c) The duration of the letter of agreement shall not exceed one year.21B.135 Maintenance of the letter of agreementThe Competent Authority shall maintain the letter of agreement as long as:(a) The manufacturer is properly using the EASA Form 52 (see Appendix) as a Statement of Conformity for completeaircraft, and the EASA Form 1 (see Appendix) for products other than complete aircraft, parts and appliances; and(b) Inspections performed by the Competent Authority of the Member State before validation of the EASA Form 52 (seeAppendix) or the EASA Form 1 (see Appendix), as per 21A.130(c) and did not reveal any findings of non-complianceagainst the requirements or the procedures as contained in the manual provided by the manufacturer, oragainst the conformity of the respective products, parts or appliances. These inspections shall check at least that:1. The agreement covers the product, part or appliance being validated, and remains valid;2. The manual described in 21A.125(b) and its change status referred in the letter of agreement is used as basicworking document by the manufacturer. Otherwise, the inspection shall not continue and therefore the releasecertificates shall not be validated;3. Production has been carried out under the conditions prescribed in the letter of agreement and satisfactorilyperformed;4. Inspections and tests (including flight tests, if appropriate), as per 21A.130(b)(2) and/or (b)(3), have been carriedout under the condition prescribed in the letter of agreement and satisfactorily performed;5. The inspections by the Competent Authority described or addressed in the letter of agreement have beenperformed and found acceptable;6. The statement of conformity complies with 21A.130, and the information provided by it does not prevent itsvalidation; and(c) Any termination date for the letter of agreement has not been reached.
帅哥
发表于 2009-4-29 13:12:01
21B.140 Amendment of a letter of agreement(a) The Competent Authority shall investigate, as appropriate, in accordance with 21B.120 any amendment of the letterof agreement.(b) When the Competent Authority is satisfied that the requirements of Section A, Subpart F continue to be compliedwith it shall amend the letter of agreement accordingly.21B.143 Notification of findings(a) When objective evidence is found by the Competent Authority, showing non compliance of the holder of a letter ofagreement with the applicable requirements of this Part, this finding shall be classified in accordance with 21A.125Band:1. A level one finding shall be notified to the holder of the letter of agreement immediately and shall be confirmedin writing within 3 working days after determination.2. A level two finding shall be confirmed in writing to the holder of the letter of agreement within 14 working daysafter determination.(b) The Competent Authority shall identify to the holder of the letter of agreement any level three finding, as defined in21A.125B(b), by appropriate means, at its convenience.27.9.2003 EN Official Journal of the European Union L 243/5321B.145 Suspension and revocation of a letter of agreement(a) In case of level one or level two findings, the Competent Authority shall partly or fully limit, suspend or revoke aletter of agreement as follows:1. In case of a level one finding the letter of agreement shall be immediately limited or suspended. If the holder ofthe letter of agreement fails to comply with 21A.125B(c)(1), the letter of agreement shall be revoked.2. In case of a level two finding, the Competent Authority shall decide on any restriction to the letter of agreementby temporary suspension of the letter of agreement or parts thereof. If the holder of the letter of agreement failsto comply with 21A.125B(c)(2), the letter of agreement shall be revoked.(b) The suspension or revocation of the letter of agreement shall be communicated in writing to the holder of the letterof agreement. The Competent Authority shall state the reasons for the limitation, suspension or revocation andinform the holder of the letter of agreement on its right to appeal.(c) When a letter of agreement has been suspended it shall only be reinstated after compliance with Section A, SubpartF has been re-established.
帅哥
发表于 2009-4-29 13:12:14
21B.150 Record keeping(a) The Competent Authority shall establish a system of record keeping that allows adequate traceability of the processto issue, maintain, amend, suspend or revoke each individual letter of agreement.(b) The records shall at least contain:1. the documents provided by the applicant for, or holder of, a letter of agreement,2. documents established during investigation and inspection, in which the activities and the final results of theelements defined in 21B.120 are stated,3. the letter of agreement, including changes, and4. minutes of the meetings with the manufacturer.(c) The records shall be archived for a minimum retention period of six years after termination of the letter of agreement.(d) The Competent Authority shall also maintain records of all Statements of Conformity (EASA Form 52, seeAppendix) and Authorised Release Certificates (EASA Form 1, see Appendix) that it has validated.SUBPART G — PRODUCTION ORGANISATION APPROVAL21B.220 Investigation(a) The Competent Authority shall appoint a production organisation approval team for each applicant, or holder of, aproduction organisation approval to conduct all relevant tasks related to this production organisation approval,consisting of a team leader to manage and lead the approval team and, if required, one or more team members. Theteam leader reports to the manager responsible for the activity as defined in 21B.25(b)(2).(b) The Competent Authority shall perform sufficient investigation activities for an applicant for, or holder of, a productionorganisation approval to justify recommendations for the issuance, maintenance, amendment, suspension orrevocation of the approval.(c) The Competent Authority shall prepare procedures for the investigation of a production organisation approval aspart of the documented procedures covering at least the following elements:1. evaluation of applications received;2. determination of production organisation approval team;3. investigation preparation and planning;4. evaluation of the documentation (production organisation exposition, procedures, etc.);5. auditing;6. follow up of corrective actions;7. recommendation for issuance, amendment, suspension or revocation of production organisation approval;8. continued surveillance.L 243/54 EN Official Journal of the European Union 27.9.200321B.225 Notification of findings(a) When objective evidence is found showing non compliance of the holder of a production organisation approval withthe applicable requirements of this Part, this finding shall be classified in accordance with 21A.158(a) and:1. A level one finding shall be notified to the holder of a production organisation approval immediately and shall beconfirmed in writing within 3 working days after determination.2. A level two finding shall be confirmed in writing to the holder of the production organisation approval within14 working days after determination.(b) The Competent Authority shall identify to the holder of the production organisation approval any level three finding,as defined in 21A.158(b), by appropriate means, at its convenience.21B.230 Issue of certificate(a) When satisfied that the production organisation is in compliance with the applicable requirements of Section A,Subpart G, the Competent Authority shall issue a Production Organisation Approval (EASA Form 55, see Appendix) without undue delay.(b) The reference number shall be included on the EASA Form 55 in a manner specified by the Agency.
帅哥
发表于 2009-4-29 13:12:29
21B.235 Continued surveillance(a) In order to justify the maintenance of the production organisation approval the Competent Authority competentauthority shall perform continued surveillance:1. to verify that the production organisation approval holder's quality system still complies with Section A, SubpartG; and2. to verify that the organisation of the production organisation approval holder operates in accordance with theproduction organisation exposition; and3. to verify the effectiveness of the production organisation exposition procedures; and4. to monitor by sample the standards of the product, part or appliance.(b) Continued surveillance shall be performed in accordance with 21B.220.(c) The Competent Authority shall provide through planned continued surveillance that a production organisationapproval is completely reviewed for compliance with this Part during a period of 24 months. The continued surveillancemay be made up of several investigation activities during this period. The number of audits may varydepending upon the complexity of the organisation, the number of sites and the criticality of the production. As aminimum the holder of a production organisation approval shall be subject to continued surveillance activity by theCompetent Authority at least once every year.21B.240 Amendment of a production organisation approval(a) The Competent Authority shall monitor any minor change through the continued surveillance activities.(b) The Competent Authority shall investigate as appropriate in accordance with 21B.220 any significant change of aproduction organisation approval or application by the holder of a production organisation approval for an amendmentof the scope and terms of approval.(c) When the Competent Authority is satisfied that the requirements of Section A, Subpart G continue to be compliedwith it shall amend the production organisation approval accordingly.21B.245 Suspension and revocation of a production organisation approval(a) In case of a level one or level two finding, the Competent Authority shall partly or fully limit, suspend or revoke aproduction organisation approval as follows:1. In case of a level one finding the production organisation approval shall be immediately limited or suspended. Ifthe holder of the production organisation approval fails to comply with 21A.158(c)(1), the production organisationapproval shall be revoked.2. In case of a level two finding, the Competent Authority shall decide on any restriction to the scope of approvalby temporary suspension of the production organisation approval or parts thereof. If the holder of a productionorganisation approval fails to comply with 21A.158(c)(2), the production organisation approval shall be revoked.27.9.2003 EN Official Journal of the European Union L 243/55(b) The limitation, suspension or revocation of the production organisation approval shall be communicated in writingto the holder of the production organisation approval. The Competent Authority shall state the reasons for thesuspension or revocation and inform the holder of the production organisation approval on its right to appeal.(c) When a production organisation approval has been suspended it shall only be reinstated after compliance withSection A, Subpart G has been re-established.
帅哥
发表于 2009-4-29 13:12:37
21B.260 Record keeping(a) The Competent Authority shall establish a system of record keeping that allows adequate traceability of the processto issue, maintain, amend, suspend or revoke each individual production organisation approval.(b) The records shall at least contain:1. the documents provided by the applicant for, or holder of, a production organisation approval certificate,2. documents established during the investigation, in which the activities and the final results of the elementsdefined in 21B.220 are stated, including findings established in accordance with 21B.2253. the continued surveillance programme, including records of investigations performed4. the production organisation approval certificate, including changes5. minutes of the meetings with the holder of the production organisation approval.(c) The records shall be archived for a minimum retention period of six years.SUBPART H — AIRWORTHINESS CERTIFICATES21B.320 Investigation(a) The competent authority of the Member State of registry shall perform sufficient investigation activities for an applicantfor, or holder of, an airworthiness certificate to justify the issuance, maintenance, amendment, suspension orrevocation of the certificate or permit.(b) The competent authority of the Member State of registry shall prepare evaluation procedures covering at least thefollowing elements:1. evaluation of eligibility of the applicant;2. evaluation of the eligibility of the application;3. classification of airworthiness certificates;4. evaluation of the documentation received with the application;5. inspection of aircraft;6. determination of necessary conditions, restrictions or limitations to the airworthiness certificates.21B.325 Issue of airworthiness certificates(a) The competent authority of the Member State of registry shall, as applicable, issue, or amend a Certificate ofAirworthiness (EASA Form 25, see Appendix), Restricted Certificate of Airworthiness (EASA Form 24, see Appendix)or Permit to Fly (EASA Form 20, see Appendix) without undue delay when it is satisfied that the applicable requirementsof Section A, Subpart H are met.(b) In addition to an airworthiness certificate for a new aircraft or used aircraft originating from a non-member State,the competent authority of the Member State of registry shall issue an initial airworthiness review certificate (EASAForm 15a, see Appendix).21B.330 Suspension and revocation of airworthiness certificates(a) Upon evidence that any of the conditions specified in 21A.181(a) is not met, the competent authority of the MemberState of registry shall suspend or revoke an airworthiness certificate.(b) Upon issuance of the notice of suspension and revocation of a certificate of airworthiness, restricted certificate ofairworthiness or permit to fly the competent authority of the Member State of registry shall state the reasons for thesuspension or revocation and inform the holder of the certificate or permit on its right to appeal.L 243/56 EN Official Journal of the European Union 27.9.200321B.345 Record keeping(a) The competent authority of the Member State of registry shall establish a system of record keeping that allowsadequate traceability of the process to issue, maintain, amend, suspend or revoke each individual airworthiness certificate.(b) The records shall at least contain:1. the documents provided by the applicant,2. documents established during the investigation, in which the activities and the final results of the elementsdefined in 21B.320(b) are stated, and3. a copy of the certificate or permit, including amendments.(c) The records shall be archived for a minimum retention period of six years after leaving that national register.SUBPART I — NOISE CERTIFICATES
帅哥
发表于 2009-4-29 13:12:56
21B.420 Investigation(a) The competent authority of the Member State of registry shall perform sufficient investigation activities for an applicantfor, or holder of, a noise certificate to justify the issuance, maintenance, amendment, suspension or revocationof the certificate.(b) The competent authority of the Member State of registry shall prepare evaluation procedures as part of the documentedprocedures covering at least the following elements:1. evaluation of eligibility;2. evaluation of the documentation received with the application;3. inspection of aircraft.21B.425 Issue of noise certificatesThe competent authority of the Member State of registry shall, as applicable, issue, or amend noise certificates (EASAForm 45, see Appendix ) without undue delay when it is satisfied that the applicable requirements of Section A, SubpartI are met.21B.430 Suspension and revocation of a noise certificate(a) Upon evidence that some of the conditions specified in 21A.211(a) are not met, the competent authority of theMember State of registry shall suspend or revoke a noise certificate.(b) Upon issuance of the notice of suspension and revocation of a noise certificate the competent authority of theMember State of registry shall state the reasons for the suspension and revocation and shall inform the holder of thecertificate on its right to appeal.21B.445 Record keeping(a) The competent authority of the Member State of registry shall establish a system of record keeping with minimumretention criteria that allows adequate traceability of the process to issue, maintain, amend, suspend or revoke eachindividual noise certificate.(b) The records shall at least contain:1. the documents provided by the applicant,2. documents established during the investigation, in which the activities and the final results of the elementsdefined in 21B.420(b) are stated,3. a copy of the certificate including amendments.(c) The records shall be archived for a minimum retention period of six years after leaving that national register.SUBPART J — DESIGN ORGANISATION APPROVALAdministrative procedures established by the Agency shall apply.SUBPART K — PARTS AND APPLIANCESAdministrative procedures established by the Agency shall apply.27.9.2003 EN Official Journal of the European Union L 243/57(SUBPART L — NOT APPLICABLE)SUBPART M — REPAIRSAdministrative procedures established by the Agency shall apply.(SUBPART N — NOT APPLICABLE)SUBPART O — EUROPEAN TECHNICAL STANDARD ORDER AUTHORISATIONSAdministrative procedures established by the Agency shall apply.(SUBPART P — NOT APPLICABLE)SUBPART Q — IDENTIFICATION OF PRODUCTS, PARTS AND APPLIANCESAdministrative procedures established by the Agency shall apply.L 243/58 EN Official Journal of the European Union 27.9.2003Appendices27.9.2003 EN Official Journal of the European Union L 243/59L 243/60 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/61L 243/62 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/63L 243/64 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/65L 243/66 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/67L 243/68 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/69L 243/70 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/71L 243/72 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/73L 243/74 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/75L 243/76 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/77L 243/78 EN Official Journal of the European Union 27.9.200327.9.2003 EN Official Journal of the European Union L 243/79
