±êÌâ: Test and Evaluation Safety [´òÓ¡±¾Ò³] ×÷Õß: ˧¸ç ʱ¼ä: 2008-12-21 21:01:22 ±êÌâ: Test and Evaluation Safety
FAA System Safety Handbook, Chapter 11: T&E Safety
December 30, 2000
Chapter 11:
Test and Evaluation Safety
11.1 INTRODUCTION ............................................................................................................ 2
11.2 TESTS CONDUCTED SPECIFICALLY FOR SAFETY ............................................... 2
11.3 TESTS CONDUCTED FOR PURPOSES OTHER THAN SAFETY............................. 2
11.4 TEST SAFETY ANALYSIS............................................................................................. 2
11.5 OTHER TEST AND EVALUATION SAFETY CONSIDERATIONS........................... 4
FAA System Safety Handbook, Chapter 11: T&E Safety
December 30, 2000
11 -2
11.0 TEST AND EVALUATION SAFETY
11.1 Introduction
Verification testing will be required at some point in the life cycle of a system and the
component(s) of a system. Tests may be conducted at many hierarchical levels and
involve materials, hardware, software, interfaces, processes, and procedures or
combinations of these. These tests determine whether requirements have been met by the
design, compatibility of personnel with equipment and operating conditions, and
adequacy of design and procedures. There are two broad types of testing which may be of
benefit to safety, which are discussed below.
11.2 Tests Conducted Specifically For Safety
Testing can be conducted to determine the existence of hazards, effectiveness of hazard
mitigation, or whether the hazard analysis is correct. This includes safe levels of stress in
mechanical systems or components, severity of damage resulting from an uncontrolled
hazard, or suitability and/or effectiveness of safety equipment. Examples include testing
such materials as plastics, lubricants, or solvents for flammability; testing of fire
extinguisher materials for effectiveness; testing the effectiveness of personnel protective
equipment; testing the radiation characteristics of RF emitters.
11.3 Tests Conducted For Purposes Other Than Safety
Testing is normally conducted to verify performance, i.e. verify that the system meets
design requirements. The data from these tests can also be used for safety purposes.
Examples include, determination of part failure rates which can be used to predict the
probability of failure; testing the strength or compatibility of new materials which can be
used to identify possible hazards; determination of interface problems between integrated
assemblies which can also define hazards; and quality control tests performed by vendors
of subcontractors. Tests performed for purposes other than safety can generate data
useful to the safety process only if the proper data is collected and documented. It is the
job of safety engineering to clearly define the safety program objectives so that test
planners will be aware of the data which will be useful to safety.
11.4 Test Safety Analysis
It is also important to consider the safety of the test itself. Safety engineers need to work
closely with test planners to ensure that the proper precautions are observed during the
testing to prevent personnel injury or equipment damage. Each proposed test needs to be
analyzed by safety personnel to identify hazards inherent in the test and to ensure that
hazard control measures are incorporated into test procedures. It is during the process of
test safety analysis that safety personnel have an opportunity to identify other data that
may be useful to safety and can be produced by the test with little or no additional cost or
schedule impact.
FAA System Safety Handbook, Chapter 11: T&E Safety
December 30, 2000
11 -3
11.4.1 Test And Evaluation Safety Tasks
A comprehensive test and evaluation safety program will involve the following activities:
¡¤ Coordinate with test planning to determine testing milestones in order to
ensure that safety activities are completed in time to support testing.
¡¤ Schedule safety analysis, evaluation and approval of test plans and other
documents to ensure that safety is covered during all testing.
¡¤ Prepare safety inputs to operating and test procedures.
¡¤ Analyze test equipment, installation of test equipment and instrumentation
prior to the start of testing.
¡¤ Identify any hazards unique to the test environment.
¡¤ Identify hazard control measures for hazards of testing.
¡¤ Identify test data that will be of use to safety.
¡¤ Review test documentation to ensure incorporation of safety requirements,
warnings, and cautions.
¡¤ Review test results to determine if safety goals have been met or if any new
hazards have been introduced by the test conditions.
¡¤ Collect data on the effectiveness of operating procedures and any safety
components or controls of the system.
¡¤ Compile safety-related test data.
¡¤ Make a determination about the safety of the system. Determine if the safety
features have been controlled as expected and if identified hazards have been
controlled to an acceptable level of risk.
¡¤ Evaluate compatibility with existing or planned systems or equipment.
¡¤ Identify deficiencies and needs for modifications.
¡¤ Evaluate lessons-learned from previous tests of new or modified systems or
tests of comparable systems to identify possible hazards or restrictions on test
conditions.
¡¤ Document and track all identified hazards to ensure resolution.
FAA System Safety Handbook, Chapter 11: T&E Safety
December 30, 2000
11 -4
11.4.2 Test And Evaluation Safety Results
A comprehensive test and evaluation safety program will produce the following products:
¡¤ Hazard analysis reports.
¡¤ Test safety analysis reports.
¡¤ Hazard tracking and risk resolution system.
¡¤ Safety analysis schedules.
¡¤ List of identified hazards.
¡¤ List of hazard control measures.
¡¤ List of required safety data.
¡¤ List of warnings and cautions.
¡¤ Reports of procedure and test plan reviews.
¡¤ Safety inputs to test planning reviews.
¡¤ Safety inputs to training materials.
¡¤ Safety inputs to operations manuals.
11.5 Other Test And Evaluation Safety Considerations
11.5.1 A system whose safe operation depends upon trained personnel
should not be tested without appropriately trained personnel.
The test personnel should undergo a training program consistent with the anticipated
operator training program. Testing a system in the operational environment using design
engineering personnel provides limited validation data. A successful OT&E program
includes training in normal operation, support, and emergency procedures. Most systems
have some residual risk (i.e., high voltages, RF energy, hot surfaces, and toxic materials)
that must be reflected in the training program. Personnel must receive training in how to
handle the residual hazards. Also, emergency procedures are developed to minimize the
impact of system failures. Personnel must be trained in these procedures. Safety must
review all operations and emergency procedures to ensure the adequacy of the procedures
and training.
11.5.2 Adequate documentation is required for correct operation and
support of a system.
Personnel must rely on manuals to supplement their training. These manuals must be
accurate and include comprehensive information on safe operation and support of the
system. Manuals must be reviewed prior to the start of the test to ensure that safety
portions are complete and provide adequate instructions, cautions, and warnings to
protect personnel and equipment.