getting to grips with fuel economy Issue 3 - July 2004 Flight Operations Support & Line Assistance getting to grips with fuel economy Issue 3 - July 2004 Flight Operations Support & Line Assistance Customer Services 1, rond-point Maurice Bellonte, BP 33 31707 BLAGNAC Cedex FRANCE Telephone (+33) 5 61 93 33 33 Telefax (+33) 5 61 93 29 68 Telex AIRBU 530526F SITA TLSBI7X Getting to grips with Fuel Economy Table of contents - 1 - TABLE OF CONTENTS TABLE OF CONTENTS 1 1. SUMMARY 4 2. PREAMBLE 5 3. INTRODUCTION 6 4. PRE-FLIGHT PROCEDURES 7 4.1 CENTER OF GRAVITY POSITION 8 4.1.1 INTRODUCTION 8 4.1.2 AUTOMATIC CENTER OF GRAVITY MANAGEMENT 8 4.1.3 INFLUENCE ON FUEL CONSUMPTION 9 4.2 TAKEOFF WEIGHT 11 4.2.1 INTRODUCTION 11 4.2.2 OVERLOAD EFFECT 11 4.2.3 AIRCRAFT OPERATING WEIGHT 12 4.2.4 PAYLOAD 13 4.2.5 EMBARKED FUEL 13 4.3 FLIGHT PLANNING 14 4.4 TAXIING 17 4.5 FUEL FOR TRANSPORTATION 19 4.6 AUXILIARY POWER UNIT 21 4.7 AERODYNAMIC DETERIORATION 23 5. IN FLIGHT PROCEDURES 24 5.1 Take-off and Initial Climb 25 5.1.1 INTRODUCTION 25 5.1.2 BLEEDS 25 5.1.3 CONFIGURATION 25 5.1.4 SPEEDS 26 5.1.5 FLEX THRUST 26 5.1.6 NOISE FLIGHT PATHS 26 5.1.7 COURSE REVERSAL 26 1 - Summary Getting to Grips with Fuel economy - 2 - 5.2 CLIMB 27 5.2.1 INTRODUCTION 27 5.2.2 THE EFFECT OF CLIMB TECHNIQUE ON FUEL BURN 28 5.2.3 CORRELATION OF FUEL BURN & TIME WITH CLIMB TECHNIQUE 31 5.2.4 CLIMB TECHNIQUE COMPARISON TABLES 34 5.2.5 DERATED CLIMB 35 5.3 CRUISE 36 5.3.1 INTRODUCTION 36 5.3.2 CRUISE ALTITUDE OPTIMISATION 37 5.3.3 CRUISE SPEED OPTIMISATION 47 5.3.4 WIND INFLUENCE 49 5.3.5 MANAGED MODE 52 5.3.6 EFFECT OF SPEED INCREASE ON MANAGED MODE 56 5.4 DESCENT 57 5.4.1 INTRODUCTION 57 5.4.2 THE EFFECT OF DESCENT TECHNIQUES ON FUEL BURN 58 5.4.3 MANAGED MODE DESCENT 60 5.4.4 EARLY DESCENT 60 5.5 HOLDING 62 5.5.1 INTRODUCTION 62 5.5.2 VARIOUS CONFIGURATION / SPEED COMBINATIONS 63 5.5.3 LINEAR HOLDING 68 5.6 APPROACH 70 5.6.1 FLIGHT PATH PRIOR TO GLIDE SLOPE INTERCEPTION 70 5.6.2 LANDING GEAR EXTENSION 70 6. DETAILED SUMMARY 71 6.1 INTRODUCTION 71 6.2 General guidelines 71 6.2.1 PRE-FLIGHT PROCEDURES 71 6.2.2 TAKE-FF AND INITIAL CLIMB 72 6.2.3 CLIMB 72 6.2.4 CRUISE 72 6.2.5 DESCENT 72 6.2.6 HOLDING 73 6.2.7 APPROACH 73 6.3 FUEL SAVINGS 73 6.4 ECONOMIC BENEFITS 75 7. CONCLUSIONS 76 Getting to grips with Fuel Economy Table of contents - 3 - 8. APPENDICES 77 APPENDIX A (Climb Charts) 78 APPENDIX B (Descent Charts) 80 1 - Summary Getting to Grips with Fuel economy - 4 - 1. SUMMARY Fuel Consumption is a major cost to any airline, and airlines need to focus their attention on this in order to maintain their profitability. This brochure looks at all the significant operating variables that affect fuel economy for the current Airbus range of aircraft. This brochure shows that there are many factors that affect fuel consumption and that the potential gains and losses are huge. Most of these factors are directly controlled by the airlines own employees (flight crew, operations/dispatch, maintenance, etc.). It can be also seen that what is good for one type of aircraft is not necessarily good for another, and that certain conceptions regarding best techniques for fuel economy are wrong. Finally for a fuel and cost economic airline, the following are the main features: • Good flight planning based on good data. • Correct aircraft loading (fuel weight and CG). • An aerodynamically clean aircraft. • Optimal use of systems (APU, Bleed, Flaps/Slats, Gear, etc). • Flight Procedures using speeds and altitudes appropriate to the companies economic priorities. • Use of the FMGS in the managed mode. • Use of performance factors in flight planning and in the FMGS derived from an ongoing aircraft performance monitoring program. Getting to grips with Fuel Economy 2 - Preamble - 5 - 2. PREAMBLE The very competitive and deregulated aviation market as well as the fear of a fuel price rise have made airlines understand how important it is to work on the fuel consumption of their fleet. Indeed airlines try to reduce their operational costs in every facet of their business, and fuel conservation has become one of the major preoccupations for all airlines, as well as aircraft manufacturers. That’s why all ways and means to reduce fuel costs have to be envisaged, safety being of course the number one priority in any airline operation. The purpose of this document is to examine the influence of flight operations on fuel conservation with a view towards providing recommendations to enhance fuel economy. It is very rare that the reduction of fuel used is the sole priority of an airline. Such instances are to maximize range for a given payload, or to decrease fuel uplift from a high fuel cost airport. Generally fuel is considered one of the direct operating costs and an airline tries to minimize total direct operating costs. This introduces the concept of Cost Index and is the scope of another brochure (Getting to Grips with the Cost Index). However it is sometimes necessary to consider the cost implication of a fuel economy, and this is done where necessary in this brochure. This brochure systematically reviews fuel conservation aspects relative to ground and flight performance. Whilst the former considers center of gravity position, excess weight, flight planning, auxiliary power unit (A.P.U.) operations and taxiing, the latter details climb, step climb, cruise, descent, holding and approach. None of the information contained herein is intended to replace procedures or recommendations contained in the Flight Crew Operating Manuals (FCOM), but rather to highlight the areas where maintenance, operations and flight crews can contribute significantly to fuel savings. 3 - INTRODUCTION Getting to grips with Fuel Economy - 6 - 3. INTRODUCTION This brochure considers the two flight management modes: “managed” mode and “selected” mode. The managed mode corresponds to flight management by means of a dedicated tool, the flight management system (FMS). Crews interface through the multipurpose control and display unit (MCDU) introducing basic flight variables such as weight, temperature, altitude, winds, and the cost index. From these data, the FMS computes the various flight control parameters such as the climb law, step climbs, economic Mach number, optimum altitude, descent law. Hence, when activated, this mode enables almost automatic flight management. When in managed mode, aircraft performance data is extracted from the FMS database. This database is simplified to alleviate computation density and calculation operations in the FMS, but individual aircraft performance factors can produce good correlation with actual aircraft fuel burns. When in selected mode, crews conduct the flight and flight parameters such as speed, altitude, and heading have to be manually introduced on the flight control unit (FCU). The cost index (CI) used in the managed mode provides a flexible tool to control fuel burn and trip time to get the best overall economics. A technique that reduces fuel burn often requires more trip time. Hence fuel savings are offset by time related costs (hourly maintenance costs, flight and cabin crew costs and marginal depreciation or leasing costs). The cost index is the cost of time ($/min) compared with the cost of fuel ($/kg) and is used to obtain the best economics. If fuel costs were the overriding priority, because fuel costs were much more significant than the cost of time, then the cost index would be low. With zero cost of time it would be zero and the FMS would fly the aircraft at Mach for max range (MMR). However if the cost of fuel was very cheap compared to the cost of time, then speed would be important and the CI would be high. For zero cost of fuel, the Cost Index would be 999 and the FMS would fly the aircraft just below MMO. Best economics would be between these two speeds and would depend on the operator’s cost structure and operating priorities. For more information on Cost Index see “Getting to Grips with the Cost Index” Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 7 - 4. PRE-FLIGHT PROCEDURES Operation of the aircraft starts with the aircraft on the ground by aircraft maintenance, preparation and loading. This part intends to highlight the impact of some ground operations on fuel consumption. Even if these operations enable only little savings in comparison with savings made during the cruise phase, ground staff has to be sensitive to them and should get into good habits. This part is divided into seven different sections: • Center of gravity position • Excess Takeoff weight • Flight Planning • Ways of taxiing to save fuel • Auxiliary Power Unit • Fuel Tankering • Aerodynamic Deterioration 4 - PRE-FLIGHT PROCEDURES Getting to grips with Fuel Economy - 8 - 4.1 CENTER OF GRAVITY POSITION 4.1.1 INTRODUCTION The gross weight is the sum of the dry operating weight, payload and fuel and acts as one force through the center of gravity (CG) of the aircraft. The balance chart allows the determination of the overall center of gravity of the airplane taking into account the center of gravity of the empty aircraft, the fuel distribution and the payload. It must be ensured that the center of gravity is within the allowable range referred to as the center of gravity envelope. A more forward center of gravity requires a nose up pitching moment obtained through reduced tail plane lift, which is compensated for by more wing lift. This creates more induced drag and leads to an increase in fuel consumption. It is better to have the center of gravity as far aft as possible. As a rearward shift in CG position deteriorates the dynamic stability of the aircraft, the CG envelope defines an aft limit. 4.1.2 AUTOMATIC CENTER OF GRAVITY MANAGEMENT AIRBUS has created a trim tank transfer system that controls the center of gravity of the airplane. This system is installed on some A300 and A310 aircraft and all A330 and A340 aircraft. When an airplane with a trim tank is in cruise, the system optimizes the center of gravity position to save fuel by reducing the drag on the airplane. The system transfers fuel to the trim tank (aft transfer) or from the trim tank (forward transfer). This movement of fuel changes the center of gravity position. The crew can also manually select forward fuel transfer. The Fuel Control and Management Computer (FCMC) calculates the center of gravity of the airplane from various parameters including input values (Zero Fuel Weight or Gross Take-off Weight and the associated CG) and the fuel tank contents. It continuously calculates the CG in flight. From this calculation, the FCMC decides the quantity of fuel to be moved aft or forward in flight to maintain the CG between the target value and 0.5% forward of the target band. Usually one initial aft fuel-transfer is carried out late in the climb to bring the CG within this band. During the flight there are several smaller forward movements as the fuel burn moves the CG more aft. Finally a forward transfer is made as the aircraft nears its destination to bring the CG within the landing CG range. Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 9 - 4.1.3 INFLUENCE ON FUEL CONSUMPTION The following graph shows the change in fuel consumption, expressed in terms of specific range (nm per kg of fuel), for both a Forward (20%) and an Aft (35%) CG position compared to a mid CG position of 27% at cruise Mach. This graph, which is for the A310-203, shows the advantage of flying at aft CG. Also shown are the optimum altitude lines and these show the effects of CG to be constant at these altitudes, with almost no variation with aircraft weight. Other aircraft have similar shape curves with similar optimum altitude characteristics (except the A320 family). The following table summarizes the effect of CG on specific range at the optimum altitude : Aircraft Type Aft CG(35-37%) Fwd CG(20%) A300-600 +1.7% -0.9% A310 +1.8% -1.8% A330 +0.5% -1.3% A340 +0.6% -0.9% For the A300/A310 reference CG is 27% and aft CG is 35%. For the A330/A340 reference CG is 28% and aft CG is 37%. Specific Range variation with CG position -3% -2% -1% 0% 1% 2% 3% 290 310 330 350 370 390 410 430 Flight Level SR Variation 140t 140t 130t 130t 110t 110t 90t 90t Weight 35% 27% 20% CG OPT FL OPT FL 4 - PRE-FLIGHT PROCEDURES Getting to grips with Fuel Economy - 10 - At maximum altitude, the change in fuel consumption given in the table is larger by up to 1%. However no benefit is obtained, as the specific range (SR) is lower at aft CG at maximum altitude than at mid CG at optimum altitude. For aircraft that are not fitted with automatic center of gravity management, not all these advantages may be realized because of the normal forward and rearward shift of CG in flight due to fuel burn. In addition loading these aircraft at max fuel to an aft CG could prove difficult. The A320 family does not show the same SR variation with CG as the other aircraft. The aft CG produces worst SR at FL290, crossing over to show an improvement at higher flight levels. The SAR variation is much smaller also. This is due to a complex interaction of several aerodynamic effects. The SAR can be considered effectively constant with CG position. Loading is therefore not critical for fuel economy for the A320 family. In order to assess the overall impact of CG variation on fuel burn, it must be assessed on a complete sector. The following table shows increases in fuel consumed with a more forward CG. It is expressed as kg per 1000nm sector per 10% more forward CG for the max variation case (high weight, high flight level) with no in flight CG shift. The fuel increment in kg is also given for the Forward (20%) position, compared with the Aft (35 or 37%) position, for a typical sector. Fuel Burn Increase with a more Forward CG Aircraft types Fuel increment KG/1000nm/10%CG Typical Sector distance (nm) Fuel increment per sector (kg) A300-600 240 2000nm 710 A310 110 2000nm 330 A319/A320/A321 Negligible 1000nm Negligible A330-200 70 4000nm 480 A330-300 90 4000nm 600 A340-200 90 6000nm 900 A340-300 80 6000nm 800 A340-500 150 6000nm 1550 A340-600 130 6000nm 1300 Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 11 - 4.2 TAKEOFF WEIGHT 4.2.1 INTRODUCTION Another way to save fuel is to avoid excess take-off weight, which consists of the operating empty weight of the aircraft plus the payload plus the fuel. In addition accurate knowledge of weight is an important factor needed to ensure that fuel burn predictions are met. This gives pilots confidence in the flight plans thus reducing the tendency to carry excess fuel. 4.2.2 OVERLOAD EFFECT The specific range, flying at given altitude, temperature and speed depends on weight. The heavier the aircraft, the higher the fuel consumption. In addition, fuel savings can be made during climb since the aircraft would reach its optimal flight level earlier if it were lighter. The effect of overloading with respect to the in-flight weight is shown on the following graph, for an excess load of 1% of MTOW (2600kg) in cruise for an A340-313 This shows the increase in specific range penalty with both weight and altitude. Maximum and optimum altitudes are shown together with selected sub optimum flight levels representing the choice of a FL below the Optimum instead of above it. For example, at 220t the optimum altitude is just under FL 350. If we select FL 330 1% extra MTOW will decrease the specific range by just under 1.2% Specific Range Penalty for Excess Weight of 1% MTOW A340-313 ISA MN 0.82 0.00% 0.50% 1.00% 1.50% 2.00% 2.50% 120 140 160 180 200 220 240 260 280 300 Aircraft Weight - Tonnes Decrease in SR Optimum Altitude Maximum Altitude Selected Sub Optimum FL FL410 FL390 FL370 FL350 FL330 FL310 FL290 4 - PRE-FLIGHT PROCEDURES Getting to grips with Fuel Economy - 12 - The characteristic curves for the other aircraft types have a similar shape. Calculating the weight effect on specific range on all Airbus aircraft in accordance with the lower boundary of typical flight levels gives an average reduction of 1% of SR for a weight increase of 1% of Maximum Take-off Weight. The scatter in this value is generally within .2%. At the higher altitudes, obtainable at lower weights, the previous picture shows that the SR reduction can increase to 1.5% Overloading affects not only the trip fuel but also the reserves and requires increased fuel uplift for a specific mission. The following table shows the effect of 1 tonne/1000nm and also 1% of basic MTOW for a typical sector, both at optimum altitude, assuming maximum passengers and some freight. Although the A320 family show considerably lower fuel burn penalties than the other aircraft, the total fuel penalty is of a similar order due to the high number of sectors per day. It can readily be seen that a 1% weight penalty has a significant impact on fuel costs when looked at on a yearly basis for a fleet of aircraft. 4.2.3 AIRCRAFT OPERATING WEIGHT The operating empty weight of an aircraft is defined as the manufacturer’s weight empty plus the operator’s items. The latter include the flight and cabin crew and their baggage, unusable fuel, engine oil, emergency equipment, toilet chemicals and fluids, galley structure, catering equipment, seats, documents, etc. The OEW of new aircraft, even in the same fleet, can vary significantly, due to specification changes, build differences and normal scatter. Also aircraft Aircraft types Payload Weight Increase Stage Fuel Penalty 1000nm/t Fuel penalty per sector Extra Reserves A300-600 31000 kg 1705 kg 2000 Nm 93 kg 320 kg 100 kg A310-300 26560 kg 1500 kg 2000 Nm 59 kg 240 kg 90 kg A318 14650 kg 640 kg 1000 Nm 31 kg 30 kg 30 kg A319 13000 kg 590 kg 1000 Nm 38 kg 50 kg 40 kg A320 17200 kg 735 kg 1000 Nm 43 kg 60 kg 45 kg A321 19100 kg 890 kg 1000 Nm 48 kg 55 kg 50 kg A330-200 29800 kg 2300 kg 4000 Nm 49 kg 460 kg 100 kg A330-300 29800 kg 2300 kg 4000 Nm 47 kg 440 kg 100 kg A340-200 29000 kg 2535 kg 6000 Nm 74 kg 1130 kg 170 kg A340-300 29000 kg 2535 kg 6000 Nm 87 kg 1330 kg 230 kg A340-500 35700 kg 3680 kg 6000 Nm 64 kg 1410 kg 210 kg A340-600 42250 kg 3650 kg 6000 Nm 65 kg 1420 kg 210 kg Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 13 - generally get heavier all through their operational life. This is due to repair schemes, service bulletins, equipment upgrades, dirt, rubbish and moisture accumulation and unnecessary equipment and supplies. This variation in weight requires regular monitoring for flight planning purposes. In general most weight growth is inevitable and it cannot be controlled at the operational level. However the airline has to be sensitive to these problems and efforts have to be made in order to avoid excess weight, such as dirt, rubbish and unnecessary equipment and supplies. It should be noted that 100kg of excess weight requires an additional 5000kg of fuel per year per aircraft. 4.2.4 PAYLOAD The most important part of the take-off weight from an airlines point of view is the payload (passengers and freight). Generally the weight of passengers, carry-on baggage and checked bags are defined in the operating rules by the authorities such as the JAA or the FAA. Most operators use standard weights although other values may be used if they can be statistically demonstrated through surveys. In general there is not much an operator can do to change the situation. However they should be aware of the rules and their validity. If the weights do not seem appropriate then an operator should consider conducting a survey. As each freight consignment is weighed, the only influence it can have on fuel economy is its location and hence the aircraft CG. 4.2.5 EMBARKED FUEL Fuel is loaded onto the aircraft to be used as follows: 1. Start-up Fuel 2. Taxi Fuel 3. Trip Fuel 4. Reserve Fuel 5. Fuel for Transportation 6. APU Fuel In order to avoid unnecessary fuel weight, the flight must be planned very precisely to calculate the exact fuel quantity to be embarked. Flight planning should be based on aircraft performance monitoring by taking into account performance factors derived from specific range variations. In addition the planning should be based on the appropriate optimized techniques using the best achievable routing and flight levels. More detailed information on this subject is given later in this brochure. 4 - PRE-FLIGHT PROCEDURES Getting to grips with Fuel Economy - 14 - 4.3 FLIGHT PLANNING The fundamental requirement for achieving fuel economy and reduction of operating costs is a quality Flight Planning System. A good flight planning system will produce an optimized route, in terms of track, speeds and altitudes, which meets the operator’s economic criteria. This track and vertical profile must be normally achievable in operation, given the constraints of ATC, climb rates, descent rates, etc. Climb, cruise and descent techniques and cruise flight levels should be optimized in accordance with the operator’s criteria, for both the sector and the diversion. This is covered in much more detail in this brochure. It will be based on good quality data (temperature, wind, aircraft weight, payload, fuel uplift, etc) It will be use the correct aircraft performance and will include an individual aircraft performance factors derived from an ongoing aircraft performance monitoring (APM) program (see “Getting to Grips with Aircraft Performance Monitoring”). Having established the climb, cruise and descent techniques, it should be verified from time to time that the aircrews are using these techniques The fuel reserves will be based on a policy that aims at obtaining the minimum values required within the regulations. Within JAR OPS, there are several definitions of Contingency fuel, depending on diversion airfields, fuel consumption monitoring, etc. Full details can be found in “Getting to Grips with Aircraft Performance”, but briefly the fuel is the greater of two quantities: 1. 5 minutes hold fuel at 1500 feet above destination at ISA 2. One of the following quantities: 5% of trip fuel, 3% of trip fuel with an available en route alternate airport 15 minutes hold fuel at 1500 feet above the destination at ISA 20 minutes trip fuel, based upon trip fuel consumption. The last 3 options require airworthiness approval and the last 2 options require fuel consumption monitoring with fuel based on results. What we can conclude is that depending on the flight distance, there is a lowest contingency fuel. Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 15 - The following graphs show the different contingency fuel quantities for different distances for an A320. The graphs for other members of the A320 family are similar and indicate that below about 500nm, the contingency fuel is set by the minimum 5-minute hold value. Above about 1000nm, contingency fuel can be reduced to 3% of trip fuel if there is an en-route alternate available. If not, reductions can be made above about 2000nm by using the 15-minute destination hold option, which always requires less fuel than the 20 minute trip fuel option. The graphs for the other aircraft show different characteristics because of their longer-range capability. The A340-600 picture, on the following page, indicates that with no enroute alternate the 15-minute destination hold requirement enables the contingency fuel to be reduced above 2150nm. An en-route alternate will give more benefit until 3500nm, beyond which the 15-minute destination hold minimises the contingency fuel requirement. The A340-500 is similar. The A300, A310, A330 and other A340’s have slightly different critical distances as follows: 5% trip fuel/15-minute hold 1700 to 1900nm. 3% trip fuel/15-minute hold 2800 to 3200nm However these will also vary with weight, winds, temperature, etc so the limiting reserve should always be checked. Each aircraft type will show critical sector distances beyond which a change in contingency policy will yield benefits. Contingency Fuel - A320-214 0 100 200 300 400 500 600 700 800 900 1000 500 1000 1500 2000 2500 3000 Sector Distance - nm Fuel - kg Minimum - 5 min Hold at 1500ft 15 min Hold at 1500ft 20 min trip fuel 3% trip fuel 5% trip fuel 4 - PRE-FLIGHT PROCEDURES Getting to grips with Fuel Economy - 16 - One further method of reducing the contingency fuel is by using a Decision Point or Redispatch Procedure. This involves the selection of a decision point where the aircraft can either continue to the destination as the remaining fuel is sufficient, or it can reach a suitable proximate diversion airport. More details are given in “Getting to Grips with Aircraft Performance”. To minimize the alternate fuel, the alternate airports should be chosen as near as possible to the destination. Both the JAA and FAA do not require the alternate fuel reserve in certain cases, depending on meteorological conditions and the suitability of the airport. More details are given in “Getting to Grips with Aircraft Performance”. Another part of the reserves is the extra fuel, which is at the Captain’s discretion. There are many reasons why this extra fuel is necessary. It could be due to uncertain weather conditions or availability of alternate and destination airfields, leading to a probability of re-routing. However it is often due to lack of confidence in the flight planning and the natural desire to increase reserves. This is the one area where a significant impact can be made through accurate flight planning. With this in place, the aircrew will see that the flight plans fuel burns are being achieved in practice. They will realize that the planned reserves are adequate and that there is no need for more. Contingency Fuel - A340-642 0 1000 2000 3000 4000 5000 6000 7000 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 Sector Distance - nm Fuel - kg Minimum - 5 min Hold at 1500ft 15 min Hold at 1500ft 20 min trip fuel 5% trip fuel 3% trip fuel Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 17 - 4.4 TAXIING Good estimate of taxi times are required. Actual times need to be monitored and standard estimates changed as necessary. Jet engine performance is optimised for flight conditions, but all aircraft spend considerable time on the ground taxiing from the terminal out to the runway and back. This time has increased due to airport congestion, and increased airport size. This all leads to a waste of precious time and fuel. Only using one engine for taxiing twin-engine aircraft, or two engines for four-engine aircraft can give benefits in fuel burn. Such procedures need to be considered carefully, and operators have to define their field of application. Airbus provides standard procedures in the Flight Crew Operating Manual (FCOM) for such operations. The following factors regarding one or two engine out taxi should be considered carefully prior to its incorporation in the operators standard operating procedures: 1. This procedure is not recommended for high gross weights 2. This procedure is not recommended for uphill slopes or slippery runways 3. No fire protection from ground staff is available when starting engine (s) away from the ramp 4. Reduced redundancy increases the risk of loss of braking capability and nose wheel steering. 5. FCOM procedures require not less than a defined time (from 2 to 5 minutes depending on the engine) to start the other engine(s) before take off. On engines with a high bypass ratio, warm-up time prior to applying maximum take off thrust has a significant effect on engine life. 6. Mechanical problems can occur during start up of the other engine(s), requiring a gate return for maintenance and delaying departure time. 7. FCOM procedures require APU start before shutting down the engine after landing, to avoid an electrical transient. 8. FCOM procedures require not less than a defined time before shutting down the other engine(s) after landing. On engines with a high bypass ratio, the cool-down time after reverse operation, prior to shut down has a significant effect on engine life. 9. If an operator decides to use one or two engine out taxi, then FCOM recommendations about which engine(s) to use should be followed. 4 - PRE-FLIGHT PROCEDURES Getting to grips with Fuel Economy - 18 - As engine-out taxi requires more thrust per engine to taxi and maneuver, caution must be exercised to avoid excessive jet blast and FOD. More thrust is necessary for breakaways and 180 degrees turns. On twin-engine aircraft slow and/or tight taxi turns in the direction of the operating engine may not be possible at high gross weight. Single engine taxi may also be considered at low weights to avoid excessive use of the brakes to control the acceleration tendency with all engines. This brake use would be detrimental to carbon brake life. The following table gives an indication of the advantages of engine out taxi for 8 of the 12 minutes total taxi time, leaving 4 minutes warm up time. Fuel savings with Engine out taxi Aircraft types 12 minutes taxi (all engines) 12 minutes taxi (8 with engine out) Engine Out taxi savings A300-600 300kg 200kg 100kg A310 240kg 160kg 80kg A318 120kg 80kg 40kg A319 120kg 80kg 40kg A320 138kg 92kg 46kg A321 162kg 108kg 54kg A330 300kg 200kg 100kg A340-200/300 300kg 200kg 100kg A340-500/600 420kg 280kg 140kg For engine out or all engines taxi, the use of a slow taxi speed costs fuel and time. A burst of power should be used to get the aircraft to taxi speed, then the power should be reduced to idle. However 30kt should not be exceeded. Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 19 - 4.5 FUEL FOR TRANSPORTATION The normal message regarding fuel burn is that it is more economical to carry the minimum amount required for the sector. However there are occasions when it is economic to carry more fuel. This is when the price of fuel at the destination airfield is significantly higher than the price at the departure airfield. However, since the extra fuel on board leads to an increase in fuel consumption the breakeven point must be carefully determined. K is the transport coefficient: The addition of one tonne to the landing weight, means an addition of K tonnes to the take-off weight. For example, if K=1.3 and 1300 kg fuel is added at the departure, 1000 kg of this fuel amount will remain at the destination. So carrying one tonne of fuel costs 300 kg fuel more. The extra-cost of the loaded fuel at departure is Fuel weight x departure fuel price (ΔTOW x Pd = ΔLW x K x Pd) The cost saving of the transported fuel is Transported fuel x arrival price (ΔLW x Pa) The cost due to a possible increase in flight time is Flight time increase x cost per hour (ΔT x Ch) It is profitable to carry extra fuel if the cost saving exceeds the extra fuel loaded cost plus the extra time cost. (ΔLW x Pa) >(ΔLW x K x Pd) + (ΔT x Ch) That is to say: ΔLW ( Pa - K x Pd) - (ΔT x Ch) > 0 LW K TOW Δ = Δ 4 - PRE-FLIGHT PROCEDURES Getting to grips with Fuel Economy - 20 - Therefore, if ΔT=0, it is profitable to carry extra fuel if the arrival fuel price to departure fuel price ratio is higher than the transport coefficient K. Pa > K Pd Thus carrying extra fuel may be of value when a fuel price differential exists between two airports. Graphs in the FCOM assist in determining the optimum fuel quantity to be carried as a function of initial take-off weight (without additional fuel), stage length, cruise flight level and fuel price ratio. The following graph is an example for an A320. However the needs for accurate fuel planning is necessary to avoid arriving at the destination airport overweight. This could result in the economic benefit being eroded or negated due to extra hold time or circuits. Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 21 - 4.6 AUXILIARY POWER UNIT The Auxiliary Power Unit (A.P.U.) is a self-contained unit which makes the aircraft independent of external pneumatic and electrical power supply and environmental conditioning. A.P.U. fuel consumption obviously represents very little in comparison with the amount of fuel for the whole aircraft mission. Nevertheless, operators have to be aware that adopting specific procedures on ramp operations can help save fuel and money. On the ground, A.P.U. fuel consumption depends on the A.P.U. type load and the ambient conditions. The minimum is when the APU is in the RTL(ready to load) condition. As additional loads, such as Electrical Loads(EL) and Environmental Conditioning System (ECS), are connected, the fuel consumption increases as shown in the following table (ISA, SL conditions). Aircraft Type APU Model RTL RTL Max EL Min ECS Max EL Max ECS Max EL A320 family 36-300 70 kg/hr 85 kg/hr 105 kg/hr 125 kg/hr A320 Family 131-9A 75 kg/hr 95 kg/hr 115 kg/hr 125 kg/hr A330, A340 331-350 120 kg/hr 140 kg/hr 175 kg/hr 210 kg/hr A340-500/600 331-600 160 kg/hr 180 kg/hr 225 kg/hr 290 kg/hr A.P.U. specific procedures to save fuel have to be defined by the operators. One extra minute of A.P.U. operation per flight at 180 kg/hr fuel flow, means an additional 3000 kg per year per aircraft. This will also result in increased maintenance costs. They have to choose between using ground equipment (Ground Power Unit, Ground Climatisation Unit, Air Start Unit) and the A.P.U. This choice depends on several parameters and each operator needs to determine the benefits at each airport and at each turnaround. Such parameters can include length of turnaround, ambient conditions, cost of ground connections, time delay to get connected, suitability and quality of ground equipment, passenger load, local noise restrictions, etc. For a long turnaround or night stop the G.P.U. is the best choice as time considerations are not prevailing. It saves both fuel and A.P.U. life. So operators are advised to use ground equipment if of a good quality, and to try to conclude agreements with airport suppliers to get preferential prices. However, for a short turnaround (45 minutes on average), the use of A.P.U. may be preferable to limit A.P.U. start cycles and improve reliability, even if it is not fully used during the turnaround. It is better to operate with A.P.U. at RTL than to shut it down and perform a new start cycle soon after shut down. Lack of suitable ground power may also require the use of APU. The use of APU 4 - PRE-FLIGHT PROCEDURES Getting to grips with Fuel Economy - 22 - may also be preferable to avoid excessive hook up charges or to reduce turnaround time. Some airport regulations restrict the use of the APU to a defined time prior to departure time and after the arrival. For extremely short turnarounds, complete engine shut down would have a cyclic cost impact, and therefore the turnaround could be made without APU. However a main engine can sometimes not meet the ECS demand in high load conditions (hot days). The disconnection of ground equipment supplies and the start of A.P.U. must be coordinated with A.T.C. pushback/slot requirements. A one-minute anticipation in each A.P.U. start will lead to a significant amount of fuel saving during a year (2000 to 4000 kg depending on A.P.U. types). Engine start up should also, if possible, be carefully planned in conjunction with A.T.C. If pushback is delayed, it is preferable to wait and use A.P.U. for air conditioning and electrical requirements. Engine start time is critical, and the engines should not be started until ready to go. The following table assuming typical engine fuel flows, shows extra fuel consumption by using one engine instead of the A.P.U. for 1 minute, assuming maximum electrical load and minimum ECS: Extra fuel when using Engine instead of APU Aircraft Type A.P.U. type Engine FF kg/hr/eng APU FF kg/hr Extra Fuel for 1 minute A300 GE 331-250 520 150kg 6kg A310 GE 331-250 520 150kg 6kg A320 family CFM 36-300 300 105kg 3kg A330 GE 331-350 520 175kg 6kg A330 RR 331-350 720 175kg 9kg A340 CFM 331-350 300 175kg 2kg A340 RR 331-600 480 275kg 4kg In overall economic terms, the benefits of APU operation are not just confined to fuel usage. The hourly maintenance costs of an APU are cheaper than the aircraft powerplant, so reducing ground running time on the engines can significantly reduce the operating costs. Getting to grips with Fuel Economy 4 - PRE-FLIGHT PROCEDURES - 23 - 4.7 AERODYNAMIC DETERIORATION Some of the most severe penalties in terms of fuel consumption are caused by increased drag resulting from poor airframe condition. Normal aerodynamic deterioration of an aircraft over a period of time can include the incomplete retraction of moving surfaces, damaged seals on control surfaces, skin roughness and deformation due to bird strikes or damage caused by ground vehicles, chipped paint, mismatched doors and excessive gaps. Each deterioration incurs a drag increase, and this increased drag is accompanied by increased fuel consumption. This subject is covered fully in the brochure “Getting Hands-On Experience with Aerodynamic Deterioration”. The following table gives the highest deterioration effect in each category for the three aircraft families as increased sector fuel consumption in Kg, based on typical utilization figures. Category Condition A300/310 A320 Family A330/340 Misrigging Slat 15mm 90 60 270 Absence of Seals Flap (chordwise) 30 14 90 Missing Part (CDL) Access Door 50 13 150 Mismatched Surface Fwd Cargo Door 10mm step for 1m 20 11 80 Door seal leakage Fwd Pax Door 5cm 2 1 5 Skin Roughness 1 m2 21 13 105 Skin Dents Single 2 1 2 Butt joint gaps Unfilled 0.2 0.1 0.6 Butt Joint Gaps Overfilled 3 2 7 External Patches 1 m2 3mm high 6 3 16 Paint Peeling 1 m2 leading edge slat 12 8 57 Sector Distance 2000nm 1000nm 4000/6000nm 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 24 - 5. IN FLIGHT PROCEDURES When an aircraft arrives at the end of the runway for take-off, it is the flying techniques (speed, altitude, configuration, etc) that have the biggest influence on fuel economy. Disciplined flight crews adhering to a flight plan based on the operator’s priorities can save much fuel and/or costs. This part intends to give recommendations to flight crews on the means to save fuel during the flight. It reviews the different phases of the flight, that is to say: • Take-off and Initial Climb • Climb • Cruise • Descent • Holding • Approach Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 25 - 5.1 TAKE-OFF AND INITIAL CLIMB 5.1.1 INTRODUCTION There are many variations in take-off technique that can directly affect the fuel burn. In general the effects are very dependent on the airframe/engine combination as well as aircraft weight, airfield altitude and temperature. The following fuel effects are representative values. 5.1.2 BLEEDS For take-off, full bleeds can be used or one can consider selecting packs off or APU bleed on to improve take-off performance. Selecting packs off without APU will also improve fuel burn. The normal procedure would then be to select pack 1 on after climb thrust is selected and pack 2 on after flap retraction. This has the effect of reducing fuel burn by 2-3 kg on an A320 increasing to 5-10 kg on an A340-500/600. With APU bleed the engine fuel burn will be decreased by the same amount. However with APU used from pushback with 12minutes taxi, the additional APU fuel burn is 30kg for an A320 and 60-70kg for an A340. In economic terms, the APU fuel and maintenance cost is largely offset due to decreased engine maintenance costs bleeds off (higher flex temp). 5.1.3 CONFIGURATION This effect is very dependent on the variables mentioned in the introduction, plus the choice of VR and V2. However the trend is always the same , with high flap/slat configurations (more extended) using more fuel than the lowest setting. Typical penalties/takeoff of higher flap settings compared with the low flap settings Conf 1+F are shown below (note that for the A300/A310 Conf 1+F, Conf 2 and Conf 3 corresponds to the Flap 0,15 and 20 configuration respectively). Aircraft Conf 2 Conf 3 A300/A310 1- 5kg 15kg A320 3-5kg 8-13kg A330 12kg 24kg A340 30kg 50kg These figures assume Full take-off thrust. The advantage of Conf 1+F increase with reduced power take-offs. 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 26 - 5.1.4 SPEEDS During a non limiting full power take-off, the use of the higher speeds appropriate to flex thrust instead of optimized speeds appropriate to the actual temperature can reduce the fuel burn by up to 8kg. 5.1.5 FLEX THRUST Compared to a full thrust take-off, flex thrust will generally increase fuel burn. The increased time at low level offsets the slight reduction in fuel flow induced by the lower thrust. Typical increases are as follows: Aircraft Conf 1+F Conf 2 Conf 3 A300/A310 10kg 10kg 10kg A320 1kg 5kg 5kg A330 0 0 0 A340 5kg 20kg 25kg 5.1.6 NOISE FLIGHT PATHS The effect of an ICAO type A noise flight path, with climb thrust selected at 800ft and clean up delayed until 3000ft is generally to increase fuel burn compared to the standard take-off with power reduced at 1500ft. The actual distance to a fixed height, say 5000ft, varies very little with configuration. The main effect is the different altitude – speed history experienced by the engines. Typical values are as follows: Aircraft Conf 1+F Conf 2 Conf 3 A320 -4kg +5kg +2kg A330 +100kg +100kg +115kg A340 +90kg +130kg +125kg 5.1.7 COURSE REVERSAL In the event that a course reversal is required after take-off, then much distance can be saved using a lower initial climb speed. Suppose ATC require an aircraft to maintain runway heading to 6000ft. A lower climb speed will achieve this altitude earlier and thus reduce the ground distance and fuel burnt. Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 27 - 5.2 CLIMB 5.2.1 INTRODUCTION Depending on speed laws, the climb profiles change. The higher the speed, the lower the climb path, the longer the climb distance. Climb profiles Climbs are normally performed in three phases on a constant IAS/Mach climb speed schedule at max climb thrust, as follows: • 250 KT indicated air speed (IAS) is maintained until flight level 100, then the aircraft accelerates to the chosen indicated air speed (e.g. “300kts); • constant indicated air speed is maintained until the crossover altitude; • constant Mach number is maintained until top of climb; Cruise level High speed Low speed Typical Climb Law 0 5000 10000 15000 20000 25000 30000 35000 40000 45000 200 250 300 350 400 450 500 Speed - ktas Altitude - ft Crossover altitude Tropopause 250 kias 300 kias M No 0.8 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 28 - The crossover altitude is the altitude where we switch from constant IAS climb to the constant Mach number climb. It only depends on the chosen IAS and Mach number, and does not depend on ISA variation. During climb, at constant IAS, the true air speed (TAS) and the Mach number increase. Then, during climb at constant Mach number, the TAS and the IAS decrease until the tropopause. To correctly evaluate the effects of climb techniques, climb and cruise flight must be viewed in relation to each other. A short climb distance for example extends the cruise distance; a low climb speed requires more acceleration to cruise speed at an unfavourable high altitude. One has therefore to consider sectors that cover acceleration to climb speed, climb, acceleration to cruise speed and a small portion of the cruise to the same distance. 5.2.2 THE EFFECT OF CLIMB TECHNIQUE ON FUEL BURN This evaluation has been made for all Airbus types, based on a climb to 35000ft, acceleration and cruise to a fixed distance. The assumed cruise speed was 0.78 for the A320 family and 0.8 for the rest. The reference climb technique is the standard technique given in each FCOM, and is summarized below: Aircraft types Speed law A300-600 250kts/300kts/M0.78 A310 (GE) 250kts/300kts/M0.79 A310 (PW) 250kts/300kts/M0.80 A318/A319/A320/A321 250kts/300kts/M0.78 A330 250kts/300kts/M0.80 A340-200/300 250kts/300kts/M0.78 A340-500/600 250kts/320kts/M0.82 Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 29 - The following chart shows the variation of fuel burn with climb technique over a given climb + cruise distance. This shows that there is an optimum climb speed and max climb Mach number that produces the lowest fuel burn. This happens to be the standard technique (300kt/0.78). Climbing at 320kt/0.82 will burn 1% more fuel. However the following chart shows that this is obtained at the expense of time. Effect of Climb Technique on Fuel to 120nm A300B4-605R ISA F/L 350 Weight 140000kg -0.2% 0.0% 0.2% 0.4% 0.6% 0.8% 1.0% 1.2% 1.4% 1.6% 260 270 280 290 300 310 320 330 340 350 Climb Speed - kias Fuel difference - % 0.76 0.78 0.80 Mach No FMG 0.82 CI "0" CI "100" Effect of Climb Technique on Time to 120nm A300B4-605R ISA F/L 350 Weight 140000kg -4% -3% -2% -1% 0% 1% 2% 3% 4% 5% 6% 260 270 280 290 300 310 320 330 340 350 Climb Speed - kias Time difference - % 0.80 0.78 0.76 Mach No FMGS 0.82 CI "0" CI "100" 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 30 - This time difference plot has the same characteristics for all Airbus aircraft, with the best time being obtained at the highest climb speed and max climb Mach number. Note that although a slow climb speed gets the aircraft to cruise altitude earlier, this requires more acceleration to cruise speed and more cruise to a given distance, making it slower overall. The fuel difference plot characteristics vary with aircraft type. The A310, A321 and A330 show similar characteristics to the A300 with a best fuel climb speed of about 290 to 300 knots. The A318, A319 and A320 show better fuel burn at the lower speed range (260 to 280 knots) The A340 shows better fuel burn at the higher speed range (310-330 knots). The A310 and A340 are similar to the A300 in showing minimum fuel at a max climb Mach number of 0.78. In fact 0.8 is better for the A340-500/600. However the A320 family and A330 benefit from the lower Mach No of 0.76. Thus the A320 family benefits from low climb speeds and the A340 from high climb speeds. This difference arises from the different behavior during climb of twin-engine and four-engine aircraft. Indeed, twin-engine aircraft have a higher thrust than four engine aircraft, as they must satisfy some take-off climb requirements with only one engine operative, compared with 3 engines operative on the quads. This enables them to have a higher rate of climb than four engine aircraft and reach cruise flight levels quicker. Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 31 - 5.2.3 CORRELATION OF FUEL BURN & TIME WITH CLIMB TECHNIQUE The following chart shows the differences in fuel and time to climb and cruise to a fixed distance with varying climb speed and max climb Mach number relative to the standard technique. This chart shows that the fastest technique (330/0.82) uses the least time (-3.2%) and the most fuel (+1.5%) whereas the slowest technique (270/0.76) uses the most time (+4.5%) and nearly the most fuel (+1.4%). The least fuel is obtained using a 300/0.78 climb technique. Variation of climb technique can cause a total variation of 1.5% and climb time by 8% for this aircraft. Also plotted on the charts are lines representing the speeds selected by the FMGS for various cost indices (CI). The left hand point of each line represents a CI of zero (fuel cost priority) and the right hand point represents a CI of 100 (flight time priority). It should be noted how the FMGS line approximates to the lower boundary of the time - fuel difference plot. The chart on the following page is for the A320 and shows completely different characteristics. Effect of Climb Technique on fuel and time to 120nm A300B4-605R ISA F/L 350 Weight 140000kg -6% -4% -2% 0% 2% 4% 6% -1% 0% 1% 2% 3% Fuel % Time % Mach No FMGS 0.76 0.78 0.8 280 300 320 330 Climb Speed KIAS 0.82 270 50kg 1 minute 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 32 - The different mach numbers all coalesce together and the FMGS line forms the common boundary. Climb speed increases from the left to the right. Least fuel is obtained using a 0.76/280 technique. Mach No has little influence, but increasing speed from 280 to 330kias decreases time by 6% and increases fuel by 6%. Completely different characteristics are also shown in the next chart (A340-642). Effect of Climb Technique on fuel and time to 200nm A320-214 ISA F/L 350 Weight 70000kg -6% -4% -2% 0% 2% 4% 6% -2% -1% 0% 1% 2% 3% 4% 5% 6% Fuel % Time % Mach No FMGS 0.76 0.8 100 kg 1 minute 270 kias 280 kias 300 kias 320 kias 330 kias Effect of Climb Technique on fuel and time to 160nm A340-642 ISA F/L 350 Weight 320000kg -2% 0% 2% 4% 6% 8% 10% -1% 0% 1% 2% 3% 4% 5% Fuel % Time % Mach No FMGS 0.76 0.78 0.8 0.82 100kg 1 minute 270 kias 280 kias 300 kias 320 kias 330 kias Climb Speed Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 33 - This shows a common technique is good for both fuel burn and time. The optimum is 320/0.80. There is little Mach No effect, but reducing the speed to 270 kias will increase fuel by 4% and time by 8%. Because the optimum technique is good for both fuel and time, there is a single FMGS point for all cost indeces. Earlier versions of the A340 showed that some marginal time benefit could be gained by climbing faster. However this would have affected the flight levels achieved. Consequently there is no variation of FMGS climb speed with cost index for all the A340 family. Appendix A presents some examples of time - fuel charts for other Airbus aircraft. 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 34 - 5.2.4 CLIMB TECHNIQUE COMPARISON TABLES The following tables show, for various Airbus aircraft, the climb time and fuel variations for a fixed distance, to FL 350, relative to a 300kias reference speed. Effect of Climb Speed on Fuel Effect of Climb Speed on Time It can be seen from the tables how the optimum techniques are very dependant on the aircraft type, and that a 10kt climb speed change can have a significant impact. Aircraft Climb ΔFuel – kg Mach No. 270KT 280 KT 300 KT 320 KT 330 KT A300 0.78 +40 +15 0 +5 +10 A310 0.79 +5 0 +5 +15 A318/A319/A320 0.78 -15 0 +30 +70 A321 0.78 -10 0 +25 +60 A330 0.80 +15 +5 0 +20 +35 A340–200 0.78 +45 +20 0 +10 +25 A340-300 0.78 +105 +50 0 -5 +20 A340-500/600 0.82 +135 0 -5 -10 Aircraft Climb ΔTime – minutes Mach No. 270KT 280 KT 300 KT 320 KT 330 KT A300 0.78 +0.8 +0.5 0 -0.3 -0.4 A310 0.79 +0.5 0 -0.5 -0.6 A318/A319/A320 0.78 +0.5 0 -0.4 -0.8 A321 0.78 +0.8 0 -0.6 -1.0 A330 0.80 +0.9 +0.6 0 -0.4 -0.7 A340–200 0.78 +1.4 +0.8 0 -0.6 -0.8 A340-300 0.78 +1.5 +0.9 0 -0.6 -1.0 A340-500/600 0.82 +0.8 0 -0.6 -0.8 Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 35 - 5.2.5 DERATED CLIMB In order to reduce engine maintenance costs, there are derated climb options available on the A330 and A340 aircraft. There are two levels of derate, D1 and D2. At a certain altitude the derate is washed out such that at Max Climb rating is achieved generally before 30000ft. The following shows a typical derate thrust variation picture, but this will vary with engine and temperature. However this derate will result in more fuel and time required to reach the same distance. The effect is dependant on aircraft weight, temperature and cruise flight level. The following table gives some typical penalties in ISA conditions to 35000ft. Derate D1 Derate D2 Aircraft Weight (kg) Fuel Increase Time Increase Fuel Increase Time Increase A330-203 190000 5kg 0.5 min 20kg 0.6 min A330-223 190000 20kg 0.2 min 40kg 0.5 min A330-343 190000 20kg 0.2 min 40kg 0.5 min A340-212 240000 65kg 0.9 min 120kg 1.5 min A340-313 240000 140kg 0.8 min 225kg 1.4 min A340-313E 240000 140kg 1.0 min 335kg 1.4 min A340-642 340000 270kg 0.6 min 445kg 1.0 min Derated Climb - Net Thrust Reduction -25 -20 -15 -10 -5 0 0 10000 20000 30000 40000 Altitude / ft Net Thrust Difference to MCL % Derated Climb 1 Derated Climb 2 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 36 - 5.3 CRUISE 5.3.1 INTRODUCTION The cruise phase is the most important phase regarding fuel savings. As it is the longest for long haul aircraft, it is possible to save a lot of fuel. So discipline must be exercised particularly in this phase. The two variables that most influence cruise fuel consumption are the cruise speed (IAS or Mach Number) and the altitude or flight level. The following shows their influence on a single sector assuming standard climb and descent procedures. The correct selection of the cruise parameters is therefore fundamental in minimizing fuel or operating cost. This chart shows the normal laws that aircraft consume less fuel when flown slower or when flown higher. However there are limits to these laws. Flying lower than the maximum range speed will increase the block fuel, as will flying higher than an optimum altitude. Block Fuel and Time for various Flight Levels and Mach numbers A330-223 ISA 3000nm Payload 30000kg JAR Reserves 35000 37000 39000 41000 43000 45000 360 380 400 420 440 460 480 500 520 540 560 Block Time - minutes Block Fuel - kg Green Dot Max Speed Range Long Range M 0.78 M 0.80 M 0.82 Flight Level 250 270 290 310 330 350 370 Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 37 - 5.3.2 CRUISE ALTITUDE OPTIMISATION In examining SR changes with the altitude at a constant Mach number, it is apparent that, for each weight, there is an altitude where SR is maximum. This altitude is referred to as “optimum altitude”. Optimum Altitude Determination at Constant Mach Number When the aircraft flies at the optimum altitude, it is operated at the maximum lift to drag ratio corresponding to the selected Mach number. High Speed Polar Curve When the aircraft flies at high speed, the polar curve depends on the indicated Mach number, and decreases when Mach increases. So, for each Mach number, there is a different value of (CL/CD)max, that is lower as the Mach number increases. M=0.84 M = 0.82 M = 0.86 M <0.76 Pressure Altitude 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 38 - When the aircraft is cruising at the optimum altitude for a given Mach, CL is fixed and corresponds to (CL/CD)max of the selected Mach number. As a result, variable elements are weight and outside static pressure (Ps) of the optimum altitude. The formula expressing a cruise at optimum altitude is: constant P Weight s = In the FCOM Flight Planning Chapters the optimum altitude is shown on the Cruise Level chart for 2 or more speeds. This chart also shows the Maximum Altitudes as limited by performance and buffet. A typical FCOM chart showing the variation of optimum altitude with weight for one speed is shown below. It should be noted that the influence of airspeed on optimum altitude is not very significant in the range of normal cruise speeds. In order to minimize fuel burn, the aircraft should therefore be flown at the optimum altitude. However this is not always possible. Performance limitations such as rate of climb or available cruise thrust can lead to a maximum altitude below the optimum, as can buffet limitations. At low weights, the optimum altitude may be above the maximum certificated altitude. In addition, Air Traffic Control restrictions can affect the flown flight level. Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 39 - The following table shows the specific range penalty of not flying at optimum altitude, assuming a cruise Mach No of 0.8. It should be noted that each airframe/engine combination has different values. It should be noted that these are average values and there are slight variations with different weight/optimum altitude combinations. Specific Range Penalty for not flying at Optimum Altitude Aircraft +2000ft -2000ft -4000ft -6000ft A300B4-605 2.0% 0.9% 3.4% 9.3% A310-324 1.9% 1.4% 4.4% 9.3% A318-111 0.7% 1.6% 5.0% 10.0% A319-132 1.0% 3.0% 7.2% 12.2% A320-211 ** 1.1% 4.7% 9.5% A320-232 1.4% 2.1% 6.2% 12.0% A321-112 2.3% 1.4% 4.6% 15.2% A330-203 1.8% 1.3% 4.2% 8.4% A330-343 3.0% 1.0% 3.2% 7.2% A340-212 1.4% 1.5% 4.0% 8.0% A340-313E 1.5% 1.6% 5.2% 9.5% A340-642 1.6% 0.6% 2.2% 5.1% ** Above Maximum Altitude Generally if one flies within 2000ft of optimum altitude, then the specific range is within about 2% of the maximum. However fuel burn-off is an important consideration. Consider an A340-313E at a weight such that the optimum altitude is 33000ft. If the aircraft flies at FL 310 the SR penalty is 2.1% for the weight considered. However after a fuel burn of 20800kg, during which the aircraft would have traveled 1400nm the optimum altitude increases to 35000ft and the penalty is now 5.2%. There is also an effect on block time due to the different altitudes. The true air speed increases/decreases 4kts, or just under 1% for each 2000ft lower/higher cruise altitude. 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 40 - 5.3.2.1 CROSS-OVER ALTITUDE VERSUS OPTIMUM ALTITUDE It has been previously shown that the TAS is the maximum at the crossover altitude. One can wonder whether it is profitable to stay at this altitude, instead of climbing to the first optimum altitude. Assuming the standard climb laws, the crossover altitude can be derived. The standard speed laws are tabulated in paragraph 5.2.2. The next table shows the effect of flying at the crossover altitude instead of optimum flight levels. The 1st optimum flight level has been chosen for the short sectors, whereas longer sectors assume step climbs with FL 310, 350 and 390 being available. This assumes ISA conditions and a take-off weight for a typical sector with max passengers and some freight (2500kg for the A320 family and 5000kg for the other aircraft). Aircraft type Sector Distance Cross-over altitude Optimum Flight Levels Gained time (min) Increase in fuel consumption A300B4-605R 2000nm 29000 ft 310/350 7 1190kg A310-324 2000nm 30000ft 350/390 3 2160kg A318-111 1000nm 29000 ft 370 3 740kg A319-112 1000nm 29000 ft 370 3 650kg A320-214 1000nm 29000 ft 350 2 580kg A320-232 1000nm 29000 ft 340 2 440kg A321-211 1000nm 29000 ft 330 2 350kg A330-203 4000nm 31000 ft 350/390 9 5040kg A330-223 4000nm 31000 ft 350/390 9 5780kg A330-343 4000nm 31000 ft 350/390 10 6380kg A340-212 6000nm 29000 ft 310/350/390 17 10900kg A340-313 6000nm 29000 ft 310/350/390 14 8410kg A340-313E 6000nm 29000 ft 310/350/390 17 9310kg A340-500/600 6000nm 29000 ft 310/350/390 18 2430kg This table shows that flying at crossover altitude increases the fuel burn significantly for a relatively small reduction in block time. Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 41 - 5.3.2.2 CRUISE OPTIMISATION WITH STEPPED CLIMB 5.3.2.2.1 Introduction It has been shown that flying at non-optimum altitudes can cause significant fuel penalties, and that the effect of fuel burn is to increase the optimum altitude. The ideal scenario would be to follow the optimum altitude as in the climbing cruise, but A.T.C. constraints, performance and buffet limits do not make this possible. However, by changing the cruise level with step climbs, as the aircraft gets lighter the aircraft will remain as close as possible to the optimum altitude. 5.3.2.2.2 Choice of Profile Several parameters such as weather conditions, ATC requirements, may influence any decision made by the crew with regard to three fundamental priorities: maneuverability, passenger comfort, and economics. This pertains to the choice of the cruise flight level that can be made according to the three following climb profiles as shown below for an A340-642: The Low profile initiates the step climb at the weight where the next available flight level is also the optimum flight level at that weight. Consequently the flight levels are always at or below the optimum. This has the advantage of better maneuverability margins and generally a better speed as it is closer to the crossover altitude. Step Climb Profiles Even Flight Levels Non RVSM 26000 28000 30000 32000 34000 36000 38000 40000 42000 0 1000 2000 3000 4000 5000 6000 7000 8000 9000 Distance from Brake Release - nm Altitude - ft Low Profile Mid Profile High Profile Optimum Altitude Maximum Altitude Maximum Altitude Optimum Altitude 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 42 - The high profile initiates the step climb at the weight where the next available flight level is also the maximum flight level at that weight. The flight levels are mainly above the optimum and the aircraft will have decreased maneuverability and fly slower. The mid profile initiates the step climb at the weight where the specific range at the next available flight level is better than that at the current flight level. This enables the flight profile to remain as close as practically possible to the optimum flight level. It is this technique that is recommended for best fuel economy, and is also very close to that required for best economics. It is interesting to note that, in this case, the Mid profile step climb is made 1140nm before the Low Profile step climb and 1520nm after the High profile step climb. The situation changes with odd flight levels: Because of the different available flight levels, the step climbs are initiated some 1500nm further than the even flight level step climb points. However the relative merits of each profile remains the same. With Reduced Vertical Separation Minima (RVSM) the difference between flight levels reduces from 4000 to 2000ft and this enables the aircraft profile to remain much closer to the optimum. In addition the high profile (depending on the aircraft) remains much higher than the optimum, increasing the fuel penalty. This profile is shown on the following page. Step Climb Profiles Odd Flight Levels Non RVSM 26000 28000 30000 32000 34000 36000 38000 40000 42000 0 1000 2000 3000 4000 5000 6000 7000 8000 9000 Distance from Brake Release - nm Altitude - ft Low Profile Mid Profile High Profile Optimum Altitude Maximum Altitude Maximum Altitude Optimum Altitude Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 43 - Thus pilots are advised to perform step climbs around the optimum altitudes. To facilitate this, the optimum weight for climb to the next flight level is given in most FCOM’s (not A300/A310). An example is shown below. Step Climb Profiles Odd Flight Levels RVSM 26000 28000 30000 32000 34000 36000 38000 40000 42000 0 1000 2000 3000 4000 5000 6000 7000 8000 9000 Distance from Brake Release - nm Altitude - ft Low Profile Mid Profile High Profile Optimum Altitude Maximum Altitude Maximum Altitude Optimum Altitude 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 44 - On all Airbus FMS-equipped aircraft, the optimum altitude (OPT FL) and the maximum flight level (MAX FL) are displayed on the MCDU progress page. The recommended maximum altitude in the FMGC ensures a 0.3g buffet margin, a minimum rate of climb of 300ft/min at MAX CLIMB thrust and a level flight at MAX CRUISE thrust. Depending on weight and type, it is 2000 to 4000ft above the optimum altitude. Typical cruise distances between 2000 foot altitude steps are shown in the following table: Type Distance - nm A300 1000 - 1100 A310 1150 - 1250 A320 1200 - 1300 A330 1500 - 1650 A340 1500 - 1650 A340-500/600 1600 - 1700 For sector lengths greater than these, where ATC restrictions do not allow a change in cruise altitude from the initial requested level, the initial request should be the highest compatible with the maximum cruise altitude. Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 45 - 5.3.2.3 DELAYS IN ALTITUDE CHANGES Let’s consider an aircraft that is at flight level 330, which has, at that weight, an optimum flight level of 370. If it does not climb to FL 370 for ATC or other reasons, it will consume more fuel. The following table shows the difference in fuel burn for a 500nm still air cruise, when cruising at FL 330 instead of FL 370. Aircraft Type Fuel Increase (kg) Fuel Increase (%) A300B4-605R 238 5.2 A310-324 221 5.3 A318-111 150 6.2 A319-132 184 7.9 A320-211 158 6.2 A320-232 187 7.9 A321-112 155 5.5 A330-203 324 5.5 A330-343 342 5.6 A340-212 393 6.2 A340-313E 378 6.0 A340-500/600 336 4.1 Thus delaying a climb to a higher altitude has a significant impact on fuel burn. 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 46 - 5.3.2.4 OPTIMUM ALTITUDES ON SHORT STAGES For short stages, the choice of cruise flight level is often restricted due to the necessary climb and descent distance. Airbus philosophy assumes a minimum 5 minute cruise sector, because a climb followed immediately by the descent is not appreciated by pilots, passengers or ATC. If the stage length is of sufficient length that the optimum flight level can be reached, but the cruise is of short duration, then the benefits at this flight level will be marginal. It may even be worthwhile to cruise at one flight level lower, as the increased climb consumption offsets any reduced cruise consumption. In the FCOM there is a chart showing the optimum altitude on a short stage. An example is shown below. Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 47 - 5.3.3 CRUISE SPEED OPTIMISATION Having been given a flight level which may be a requested optimum altitude or one imposed by air traffic control, speed is the only remaining parameter that requires selection. The following picture shows the variation of Specific Range with Mach Number for different aircraft weights at a fixed altitude. The Mach number, which gives the best specific range, can be determined. It is called the maximum range cruise Mach (MMR). Nevertheless, for practical operations, a long-range cruise procedure is defined which gains a significant increase in speed compared to MMR with only a 1% loss in specific range. Like the MMR speed, the MLRC speed also decreases with decreasing weight, at constant altitude. A more detailed explanation of this can be found in “Getting to Grips with Aircraft Performance” 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 48 - The following chart shows the typical variation of the Long Range Cruise Mach Number with aircraft weight for various flight levels. Also plotted on this chart is the optimum altitude line. This shows that there is not much variation in the long-range cruise mach number at these altitudes. It would therefore be possible to fly a constant Mach number procedure instead of the variable LRC speed procedure. In order to save fuel however, the exact LRC speed should be maintained. Long Range Cruise Mach Number A330-243 ISA 0.72 0.74 0.76 0.78 0.8 0.82 0.84 160 170 180 190 200 210 220 230 240 Aircraft Weight (1000kg) Mach Number 270 290 310 330 350 370 390 410 Flight Optimum Altitude The Long Range Cruise Speed can be found in the Cruise tables in the FCOM. Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 49 - 5.3.4 WIND INFLUENCE Wind can have a significant influence on fuel burns. Nowadays, meteorological forecasts are very reliable and its integration into the FMS provides accurate information to crews. Hence the latter best perform flight planning with a view towards fuel savings. The effect of the wind on trip time and fuel is shown on the following chart, which gives fuel consumption and time for a 2000nm sector, with respect to flight levels, Mach number and wind (tailwind positive) for a fixed take-off weight. This plot graphically shows the magnitude of the significant changes in fuel consumption and time due to winds. FCOM Tables show the equivalent still air distances for any ground distance/wind combination. However the winds can affect the performance optimization as well as changing the effective still air distance. The MMR (or MLRC) value varies with headwind or tailwind, due to changes in the SR. The effect of a tailwind is to increase the ground speed, and therefore the SR, by the ratio of ground speed to airspeed. A given wind speed therefore has a larger effect at the lower airspeeds, which changes the optimum speed. A321 FL 350 FL 330 FL 310 FL 290 FL 330 FL 350 FL 310 FL 290 11000 12000 13000 14000 15000 16000 17000 18000 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 5.7 Time (hour) Fuel consumption (kg) M 0.8 M 0.78 M 0.76 M 0.8 M 0.78 M 0.76 M 0.8 M 0.78 M 0.76 M 0.8 M 0.78 M 0.8 M 0.76 M 0.78 M 0.76 -60 kts -30 kts 30 kts 60 kts 0 kts 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 50 - The following chart shows the Maximum Range Mach number versus wind variations. MMR and wind influence This shows that Tailwinds increase the specific range and lower the speeds Headwinds decrease the specific range and raise the speeds. The wind speed can be different at different altitudes. For a given weight, when cruise altitude is lower than optimum altitude, the specific range decreases. Nevertheless, it is possible that, at a lower altitude with a favorable wind, the ground specific range improves. When the favorable wind difference between the optimum altitude and a lower one reaches a certain value, the ground-specific range at lower altitude is higher than the ground-specific range at optimum altitude. As a result, in such conditions, it is more economical to cruise at the lower altitude. There is information in the most FCOM’s (not A300/310) to indicate the amount of favorable wind, necessary to obtain the same ground-specific range at altitudes different from the optimum. If the wind is more favorable then it is beneficial to fly lower. The following shows such a page: Given weight and Pressure Altitude Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 51 - IN FLIGHT PERFORMANCE CRUISE 3.05.15 P 7 SEQ 020 REV 24 WIND ALTITUDE TRADE FOR CONSTANT SPECIFIC RANGE GIVEN : Weight : 68000 kg (150 000 lb) Wind at FL350 : 10 kt head FIND : Minimum wind difference to descend to FL310 : (26 − 3) = 23 kt RESULTS : Descent to FL310 may be considered provided the tail wind at this altitude is more than (23 − 10) = 13 kt. 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 52 - 5.3.5 MANAGED MODE The flight management system (FMS) optimizes the flight plan for winds, operating costs and suggests the most economical cruise altitude and airspeed, depending on the cost index chosen by the airline. An airline that wants to save fuel has to choose a low cost index. The next part intends to highlight the impact of the cost index on fuel consumption and on trip time. More complete information can be found in the “Getting to Grips with Cost Index” brochure. 5.3.5.1 ECONOMIC MACH NUMBER Long-range Cruise Mach number was considered as a minimum fuel regime. If we consider the Direct Operating Cost instead, the Economic Mach number (MECON), can be introduced. Direct Operating Costs (DOC) are made up of fixed, flight-time related and fuel-consumption related costs. As a result, for a given trip, DOC can be expressed as: DOC C C F C T C F T = + .Δ + .Δ where CC = fixed costs CF = cost of fuel unit ΔF = trip fuel CT = time related costs per flight hour ΔT = trip time As DOCs are calculated per nautical mile, it is possible to plot fuelrelated costs, flight-time related costs, and direct operating costs based on Mach number . Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 53 - Minimum fuel costs correspond to the Maximum Range Mach number. The minimum DOC corresponds to a specific Mach number, referred to as Econ Mach (MECON). ECON ECON weight constant FL M constant weight M = ⇒ FL = ⇒ The MECON value depends on the time and fuel cost ratio. This ratio is called cost index (CI), and is usually expressed in kg/min or 100lb/h: F T C C = Cost of fuel Cost Index (CI) = Cost of time Depending on the cost index, the predicted aircraft and atmospheric conditions, the optimum altitude and the economic Mach number are computed. From then on, fuel consumption depends only of the chosen cost index. The following chart shows the economic Mach number variation with flight level for different cost indices. This shows the general trend, common with all aircraft, of increasing economic Mach number with flight level. Economic Cruise Mach Number A310-324 ISA 130000kg 0.73 0.74 0.75 0.76 0.77 0.78 0.79 0.8 0.81 0.82 290 300 310 320 330 340 350 360 370 380 Flight Level ECON Mach Optimum F/L Maximum F/L 0 20 40 60 80 100 Cost Index 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 54 - The charts also show large economic Mach number changes with flight level for low cost indices, whereas it is rather constant for high cost indices. The economic Mach is very sensitive to the cost index when flying below the optimum altitude. The effect of weight variation at a fixed flight level is shown below. The charts show that for high cost indices, the economic Mach number stays fairly constant throughout the flight. Nevertheless, for a low cost index, the economic Mach number reduces significantly as the weight reduces. This is quite normal as low cost indices favor fuel consumption at the expense of time. Moreover, we notice that for low cost indices, a small cost index increment has a far-reaching influence on the economic Mach number, and hence on flight time. These trends are typical of all aircraft. Economic Cruise Mach number A310-324 ISA F/L 350 0.7 0.72 0.74 0.76 0.78 0.8 0.82 90 95 100 105 110 115 120 125 130 135 140 Aircraft Weight - tonnes ECON Mach 0 20 40 60 80 100 Cost Index Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 55 - 5.3.5.2 TIME/FUEL RELATIONSHIP To know whether the fuel economies at low cost indices are worthwhile, the impact of cost index on time has to be considered. The following graph show both trip fuel and time for different flight levels and cost indices. The shape of this chart is typical of all types. As it can be seen, it is not really advantageous to fly at very low cost indices as fuel savings are not significant compared to time loss. Although using slightly higher fuel, a slightly higher cost index gives significant time gains. For instance, for the A319, increasing the cost index from 0 to 20 reduces the block time by 15 minutes (5%) for a fuel burn increase of only 200kg (2%) on a 2000nm sector. A319 FL390 FL370 FL350 FL330 FL310 FL290 FL390 FL370 FL350 FL330 FL310 FL290 FL390 FL370 FL350 FL330 FL310 FL290 9000 9500 10000 10500 11000 11500 12000 12500 13000 4.2 4.4 4.6 4.8 5 5.2 5.4 time (hours) fuel consumption (kg) CI=0 CI=20 CI=40 CI=60 CI>100 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 56 - 5.3.6 EFFECT OF SPEED INCREASE ON MANAGED MODE Flying at a given cost index rather than at a given Mach number provides the added advantage of always benefiting from the optimum Mach number as a function of aircraft gross weight, flight level and head/tailwind components. This means the ECON mode (“managed” mode) can save fuel relative to fixed Mach schedules (“selected” mode) and for an equivalent time. One can wonder whether selecting a higher Mach number than the one chosen by the FMS has a significant impact on fuel consumption. Imagine an aircraft flying at flight level 370, in managed mode and at the optimum weight of FL370. The FMS computes the optimum speed based on cost index, temperature and wind. If the pilot selects another (higher) Mach number, the fuel consumption will increase. The following tables show the effect of such a speed increase. We notice that although decreasing block times, the increase of Mach number above the Optimum speed can result in significant increases in fuel burn. Pilots hence have to be patient and should not change the Mach number even when under the impression that the aircraft does not fly fast enough. Moreover, when possible, the managed mode must be kept. Economic Mach No + 0.005 Economic Mach No + 0.01 Fuel Penalty ΔTime Fuel Penalty ΔTime Aircraft Sector Kg % Min Kg % Min A300-605 2000 Nm 110 0.4 1 230 0.9 3 A310-324 2000 Nm 90 0.4 1 430 2.0 8 A318 1000 Nm 30 0.5 1 60 1.0 1 A319 1000 Nm 20 0.2 1 40 0.6 2 A320 1000 Nm 20 0.3 1 40 0.7 2 A321 1000 Nm 10 0.1 1 30 0.4 1 A330 4000 Nm 150 0.3 3 330 0.6 6 A340-212 6000 Nm 390 0.5 5 790 0.9 10 A340-313E 6000 Nm 380 0.4 5 900 1.0 10 A340-500 6000 Nm 1050 0.9 5 2540 2.1 9 A340-600 6000 Nm 820 0.7 4 2060 1.8 9 Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 57 - 5.4 DESCENT 5.4.1 INTRODUCTION Depending on the descent law, flight paths do vary in steepness. Indeed, the higher the speed law, the steeper the flight path. Descent profiles. Descents are normally performed in three phases on a constant IAS/Mach descent speed schedule, as follows: • Constant Mach number is maintained until the crossover altitude • Constant indicated air speed is maintained down to 10000ft • 250 KT indicated air speed (IAS) is maintained below flight level 100, until the aircraft decelerates for landing The engine thrust is normally set to flight idle for the descent and the speed is controlled by the aircraft attitude. In these conditions higher weights increase the descent distance because of the reduction of descent gradient (which equals [thrust-drag]/weight in stabilized flight). This also increases the descent fuel. However a descent from high altitudes at low weight may lead to a gradient of descent that results in an excessive cabin rate of descent. In these cases the rate of descent is reduced by application of power, until a flight idle descent can be continued. This results in what is known as the re- pressurization segment, and this can reverse the weight-descent distance relationship. To correctly evaluate the effects of descent techniques, cruise and descent flight must be viewed in relation to each other. A short descent distance for example extends the cruise distance. One has therefore to consider in addition to the descent, a small portion of the cruise to the same distance. High speed Low speed Cruise level TOD 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 58 - 5.4.2 THE EFFECT OF DESCENT TECHNIQUES ON FUEL BURN An evaluation has been made of the fuel burn to a constant distance, and this now shows that the higher weights use less fuel. Lower speeds, although requiring more fuel for the descent only requires less total fuel because of the longer descent distance. This is shown in the following chart. At a fixed weight, the following chart shows that the minimum fuel occurs at a descent speed of 240kias to 280kias, dependant on flight level. However there is a significant time penalty at these speeds. Effect of Descent Technique on Fuel and Climb for 115nm A310-324 ISA 110000Kg 17.5 18.0 18.5 19.0 19.5 20.0 20.5 21.0 21.5 300 350 400 450 500 550 600 650 Fuel - kg Time - min 240 250 260 300 320 330 3 13 33 54 74 100 390 370 Initi3a5l 0Flight Level330 310 Cost Index Descent Speed KIAS 280 Effect of Descent technique on Fuel and Time for 115nm A310-324 ISA F/L 350 17.5 18.0 18.5 19.0 19.5 20.0 20.5 380 400 420 440 460 480 500 520 540 Fuel - kg Time - min 90t 110t 130t 260 280 300 320 Aircraft Weight Descent Speed kias Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 59 - Note that the effect of the descent Mach number is very dependant on cruise flight level and descent speed, but is relatively small compared to the descent speed effect, and is not fully investigated here. These descent charts are typical of the other Airbus aircraft. Generally they show a minimum fuel speed of 260 to 280 kts for flight level 310, reducing to 240kts for flight level 390. The exceptions are the A318, A319, A320 and A330, which show the minimum fuel at 240kias for all flight levels which is slightly lower than the other aircraft at FL310. Appendix B presents some examples of these descent charts for other Airbus aircraft. The following tables show, for various Airbus aircraft, the descent time and fuel variations for a fixed distance, from FL 350, relative to a 300kias reference speed. * A300/A310/A320 330kias A330/A340 340kias Type ΔFuel – kg 240KT 260 KT 280 KT 300 KT 320 KT 330/340KT * A300 -55 -60 -30 0 25 35 A310 -55 -60 -30 0 25 40 A318, 319, 320 -50 -40 -20 0 20 25 A321 -35 -40 -20 0 20 35 A330 -110 -105 -60 0 50 70 A340–200/300 -70 -90 -50 0 50 75 A340-500/600 -125 -130 -70 0 70 100 Type ΔTime – minutes 240 KT 260 KT 280 KT 300 KT 320 KT 330/340KT * A300 2.7 1.5 0.6 0 -0.4 -0.6 A310 2.4 1.4 0.6 0 -0.4 -0.6 A320 family 2.6 1.4 0.6 0 -0.4 -0.6 A330 3.5 2.0 0.8 0 -0.6 -0.8 A340–200/300 3.2 1.8 0.8 0 -0.6 -0.8 A340-500/600 3.3 1.9 0.8 0 -0.6 -0.8 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 60 - Comparing these tables to the equivalent climb comparison tables in chapter 5.2.4, it can be noticed that descent techniques often have a greater effect on fuel and time than climb techniques. 5.4.3 MANAGED MODE DESCENT The FMS computes the Top Of Descent (TOD) as a function of the cost index. We notice that the higher the cost index: The steeper the descent path (the higher the speed) The shorter the descent distance The later the top of descent. Descent performance is a function of the cost index; the higher the cost index, the higher the descent speed. But contrary to climb, the aircraft gross weight and the top of descent flight level appear to have a negligible effect on the descent speed computation. It can be noticed that time to descent is more dependant on cost indices than the time to climb. On the Effect of Descent Technique on Fuel and Time chart, the cost index has been annotated for each speed. It can be seen that the minimum fuel is at a CI of 0, and the minimum time occurs with a high CI, as would be expected. For the A300, A310 and A320 family the speed at zero cost index is about 250kias. For the A330/340 it is about 270kias. Max speed normally corresponds with a high cost index of 60 to 120. Once more it can be seen how, in the managed mode, the cost index is used to choose the balance between fuel burn and flight time. 5.4.4 EARLY DESCENT If the aircraft begins its descent too early, the aircraft would leave its optimal flight level, where fuel consumption is at its best, and would have to cruise at a lower altitude to arrive at the same point. Cruise Flight Level • TOD Early Descent FL 100 Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 61 - Two descent situations were simulated: • Descent commenced 15nm (or about 2 minutes) early followed by a leveloff at FL100. • Cruise continued from the early descent point until the optimum start of descent, followed by the descent At 10000ft, the cruise speed could be selected between LRC and max speed. If in managed mode, one could continue at the same cost index, or select the 250kias below 10000ft limiting speed. The following table compares the two options. Aircraft 250KIAS at FL100 LRC at FL100 ΔFuel – kg ΔTime – min ΔFuel – kg ΔTime – min A300-600 70 1.1 95 0.4 A310 70 1.1 90 0.3 A320 family 50 1.1 65 0.2 A330 80 1.2 100 0.5 A340-200/300 95 1.2 105 0.5 A340-500/600 135 1.2 125 0.5 Cruising faster at 10000ft reduces the time penalty at the expense of fuel. After a long flight with an A340–500 or –600, starting the descent some 100nm early would not appear to be significant in the overall flight. However this can result in a 900kg fuel burn increase and 8 minutes longer block time. 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 62 - 5.5 HOLDING 5.5.1 INTRODUCTION When holding is required, it is generally flown on a “race track pattern”, composed of two straight legs plus two 180 degree turns. In a hold the distance covered is not the primary objective. On the contrary, the knowledge of the maximum holding time (maximum endurance) is a determining factor for any diversion decision. As a result, it is important, during holding, to try to minimize fuel by simply minimizing fuel flow. For all aircraft, the minimum fuel consumption speed is very close to the maximum lift-to-drag ratio (Green Dot) speed as shown below. As a result, in clean configuration, the standard holding speed is selected equal to green dot speed (GD). Fuel Consumption A330-343 170000kg 1500ft 0 2000 4000 6000 8000 160 180 200 220 240 260 280 300 320 Speed - Knots CAS Fuel Consumption kg/hr GD Min Fuel Min Drag Max Range Long Range Holding patterns may be quite limiting around certain airports due to obstacle proximity. Therefore, green dot is sometimes too high, especially during turn phases where the bank angle can be too significant. As it is not possible to significantly reduce the speed below green dot in clean configuration, slats may be extended and a holding done in CONF1 at “S” speed. (min slat retraction speed Conf 1 to Conf clean). At other airports, Air Traffic Control may require the hold to be performed at a certain speed, and it may not be possible fully optimise the fuel burn. In order to Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 63 - allow flexibility in planning and operations, the FCOM has four different holding speed and configuration combinations, adapted to each type of aircraft. The following table gives the configurations and speeds for each type. Aircraft types First Flap/slat Configuration Clean configuration A300-600 210kts S speed 240kts Green Dot A310 170kts S speed 210kts Green Dot A320 Family (CFM) 170kts S speed 210kts Green Dot A320 Family (IAE) 170kts S speed 210kts Green Dot + 20 A330 170kts S speed 210kts Green Dot A340-200/300 210kts S speed 240kts Green Dot A340-500/600 240kts S speed - Green Dot For the A300/A310 the first configuration is flap 15, slat 0. For the other aircraft this is Conf 1. Note that the fourth combination for the A340-500/600 is Configuration 2 at 210kts. 5.5.2 VARIOUS CONFIGURATION / SPEED COMBINATIONS The following graphs show the holding fuel flow variation with weight for the four different holding configurations. This is done at an altitude of 10000ft. Effect of Holding Technique on Fuel Flow A300B4-605R ISA F/L 100 2500 3000 3500 4000 4500 5000 90 95 100 105 110 115 120 125 130 Aircraft Weight - tonnes Fuel Flow - kg/h Clean Green Dot Clean 240 kt 15/0 'S' Speed 15/0 210kt 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 64 - This graph is for an A300 and it shows the advantage of holding in a clean configuration at the green dot speed. The clean configuration fixed speed of 240kt is significantly higher than the green dot speed; hence the large increase in fuel flow with this technique. The 15/0 configuration with a fixed speed of 210kt is also significantly higher than the ‘S’ speed, hence higher fuel flows. The large variation in fuel flow shows how important it is to use the right configuration and speed, compatible with the other operational requirements. The A340-200/300 schedules the same hold speeds as the A300, and the graphs have a similar form with a large increase in fuel flow at low weights with the fixed speed techniques. However at high weights the difference is much smaller. There is also a large increase when using Conf 1. Once more holding clean at green dot speed gives the lowest fuel flow. The following graph is for the A310 and this shows completely different characteristics because of the lower fixed speeds used in each configuration. Each configuration shows very similar fuel flow, whichever speed technique is used. The clean configuration green dot speed still represents the best single choice for lowest fuel burn over the normal holding weight range. The A330, which has the same hold speed schedules shows the same characteristics, with clean configuration at green dot speed being marginally better than clean configuration at 210kt over the normal holding weight range. The A320 family shows a completely different set of characteristics as shown in the graph on the next page. Effect of Holding Technique on Fuel Flow A310-324 ISA F/L 100 2500 3000 3500 4000 4500 5000 90 95 100 105 110 115 120 125 130 Aircraft Weight - tonnes Fuel Flow - kg/h Clean Green Dot Clean 210kt 15/0 'S' Speed 15/0 170kt Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 65 - The variation of different techniques is very weight sensitive. However it is still the clean configuration at green dot speed that gives the lowest fuel flow. This picture is typical of all the A320 family. Finally the A340-500/600 has another set of configuration/speed combinations and the following graph shows its different characteristics, but the basic concept that the clean configuration and green dot is the best combination still remains true. Effect of Holding Technique on Fuel Flow A320-214 ISA F/L 100 1400 1600 1800 2000 2200 2400 2600 2800 40 45 50 55 60 65 70 Aircraft Weight - tonnes Fuel Flow - kg/h Clean Green Dot Clean 210kt Conf 1 'S' Speed Conf 1 170kt Effect of Holding Technique on Fuel Flow A340-642 ISA F/L 100 5500 6000 6500 7000 7500 8000 8500 9000 9500 10000 200 220 240 260 280 Aircraft Weight - tonnes Fuel Flow - kg/h Clean Green Dot Conf 1 240kt Conf 1 'S' Speed Conf 2 210kt 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 66 - There is also altitude to be considered, although it is often not the operator’s decision what flight level to hold at. Altitude has different effects on the fuel flow, depending on the airframe/engine combination. However, whatever the altitude effect, it generally affects all techniques equally; generally the higher the hold altitude the lower the fuel flow. This however is true only up to a certain altitude and this varies with each type. The following table shows this altitude effect for a hold in the clean configuration at green dot speed. The holding fuel flow is compared with the lowest for the flight levels considered for each type, and the difference expressed as a percentage. Flight Level 50 100 150 200 250 300 350 400 A300B4-605R 4 2 1 0 3 8 16 A310-324 11 5 2 0 0 5 9 23 A318-111 13 8 4 2 1 0 0 5 A319-112 19 11 3 1 0 1 0 4 A320-214 13 5 3 1 1 1 0 2 A320-232 7 5 5 5 2 0 4 11 A321-211 14 11 8 3 0 1 5 A330-203 2 1 0 0 2 4 8 18 A330-223 9 9 5 2 0 1 6 14 A340-343 10 5 1 0 0 2 7 16 A340-212 3 2 0 0 2 3 5 A340-313E 2 1 0 0 2 3 5 A340-642 6 2 0 1 2 3 4 11 In order to allow an assessment of the sensitivity of each aircraft type to different hold techniques, the following table shows the extra fuel required to hold for 15 minutes at 10000ft in the first flap configuration at ‘S’ speed, compared to Conf clean at green dot speed. Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 67 - Effect of Holding in First flap Setting at ‘S’ speed compared with Clean at Green Dot speed Aircraft types Fuel Increase (kg) Low Holding Weight Fuel Increase (kg) High Holding Weight A300B4-605R 70 110 A300B4-622R 110 190 A310-324 70 135 A318 5 10 A319 10 30 A320 10 30 A321 30 50 A330-203 135 175 A330-223 175 205 A330-343 145 175 A340-212 170 230 A340-313 125 175 A340-642 130 150 The table shows that the green dot speed/clean configuration combination enables significant savings to be made. However, green dot speed increases with weight and can become higher than the maximum recommended speeds, which are listed below: Levels ICAO PAN-OPS FAA France Up to 6,000 ft inclusive 230 KT 210 KT 200 KT 220 KT Above 6,000 ft to 14,000 ft inclusive 230 KT 230 KT 230 KT 220 KT Above 14,000 ft to 20,000 ft inclusive 240 KT 240 KT 265 KT 240 KT Above 20,000 ft to 24,000 ft inclusive 265 KT 240 KT 265 KT 240 KT Above 24,000 ft to 34,000 ft inclusive 265 KT 240 KT 265 KT 265 KT Above 34,000 ft M 0.83 240 KT 265 KT M 0.83 If green dot is higher than these maximum recommended speeds, it is advised to hold in configuration 1 at “S” speed below 20000ft: keeping clean configuration coupled with a speed reduction would save fuel but would decrease the speed margins which are especially important in turbulent conditions. 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 68 - 5.5.3 LINEAR HOLDING If holding is going to be necessary, linear holding at cruise flight level and at green dot speed should be performed whenever possible since total flight time will remain constant (cruise time is increased but holding time is reduced) and fuel flow is lower at high flight levels. If A.T.C. informs 15 minutes before reaching a fix and that 10 minutes holding is expected. Two options are possible: • The aircraft is flown 15 minutes at cruise speed and holds for 10 minutes at green dot speed. • The aircraft performs the cruise to reach the fix at green dot speed and holds for the remaining time at the same speed. 10 minutes holding at green dot speed 15 minutes at cruise d Holding at cruise Holding for remaining time at green dot speed Cruise at green dot speed Holding optimization Getting to grips with Fuel Economy IN FLIGHT PROCEDURES - 69 - ATC restrictions may not permit a cruise speed reduction at the cruise flight level, or permit a hold at the cruise flight level. The standard procedure would be to continue to the top of descent at cruise speed and descend to a flight level to join the stack. However if ATC permit a linear hold it can give significant fuel savings. However the amount of savings is very dependant on the characteristics of the aircraft type. The increase in time in the cruise depends on how much slower green dot speed is compared to the normal cruise speed. This increase was much higher with the A320 than the A340. In addition, most aircraft, flying the same cruise distance at green dot speed actually uses a little more fuel at these altitudes. The following table shows the gains due to cruising slower and spending less time in the hold at the cruise flight level. Advantages of a 15min linear hold at cruise altitude at Green Dot speed Aircraft type Weight kg Cruise Flight Level Cruise Speed Fuel savings kg A300 120000 350 0.8 95 A310 110000 350 0.8 115 A318 50000 350 0.78 120 A319 50000 350 0.78 135 A320 60000 350 0.78 80 A321 70000 350 0.78 50 A330 180000 390 0.82 95 A340-200 200000 390 0.82 10 A340-300 200000 390 0.82 45 A340-500/600 270000 390 0.82 5 The high green dot speed for the A340 leads to very little advantage in linear holding. However the other aircraft show significant benefits. If the increase in cruise time can be used to reducing the time in the holding pattern or stack, then the benefits will be similar to those shown in the table above. However the constraints of ATC are unlikely to let these benefits accrue. 5 - IN FLIGHT PROCEDURES Getting to grips with Fuel Economy - 70 - 5.6 APPROACH 5.6.1 FLIGHT PATH PRIOR TO GLIDE SLOPE INTERCEPTION Procedures used in the approach phase can affect the amount of fuel consumed in this phase of the flight. The glide slope can be intercepted either horizontally between 1500ft and 2000ft or in a descending flight path above 2000ft. This latter method uses less fuel, but the amount is difficult to quantify, as it depends on the exact flight paths in each case. However, the most important feature of an approach is that it should be well executed, stabilized and safe. None of these features should be compromised in an attempt to save fuel, and the procedure flown should be that appropriate to the airport, runway, equipment, conditions, etc. 5.6.2 LANDING GEAR EXTENSION The standard procedure is that Gear Down is selected down when Conf 2 (or flap 20 for A300/310) is achieved. The effect of extending the gear prior to this point will increase fuel burn, but the amount is difficult to quantify without knowing when the gear is extended. However, the most important feature of an approach is that it should be well executed, stabilized and safe. The use of gear is often one of the means of achieving this through speed control, and gear extension should not be delayed to save fuel. Getting to grips with Fuel Economy 6 - DETAILED SUMMARY - 71 - 6. DETAILED SUMMARY 6.1 INTRODUCTION In this brochure it can be seen that there are many ways of influencing the fuel burn of an aircraft, but most depend on the way that the sector is planned and flown. Maximising the fuel economy requires: • Good flight planning based on good data. • Correct aircraft loading (weight and cg). • An aerodynamically clean aircraft. • Optimal use of systems (APU, Bleed, Flaps/Slats, Gear, etc). • Flight Procedures using speeds and altitudes appropriate to the companies economic priorities. • Use of the FMGS in the managed mode. • Use of performance factors in flight planning and in the FMGS derived from an ongoing aircraft performance monitoring program. 6.2 GENERAL GUIDELINES 6.2.1 PRE-FLIGHT PROCEDURES • For most Airbus aircraft, an aft CG position saves fuel. • Excess weight costs fuel. Minimize zero fuel weight and embarked fuel. • A good flight planning system will minimise fuel through correct optimisation. • An aircraft performance measurement system and good flight planning will give confidence in fuel burn reducing extra reserve. • Keep A.P.U. running during short turnarounds to reduce A.P.U. start cycles. • Use ground power, when possible to save both fuel and A.P.U. life. 7 – CONCLUSIONS Getting to grips with Fuel Economy - 72 - • Do not start engines until ready to go. • If considered operationally acceptable, taxi with one engine out. • Keep the aircraft in an aerodynamically clean condition. 6.2.2 TAKE-FF AND INITIAL CLIMB • Bleeds off fuel improvements normally negated by APU fuel burn • Lower configurations do save fuel. • Flex thrust cost fuel but saves engine costs. • Noise flight paths cost fuel 6.2.3 CLIMB • Climb as close as possible to the optimum climb law. • Fast Climb speeds use more fuel (except A340) 6.2.4 CRUISE • The best speed for fuel burn (very low cost index) is slow and has a big time penalty. • If possible, fly in managed mode at the cost index appropriate to the airlines economic priorities. • Flying faster than the FMGS economical Mach number costs fuel. • Try to fly at optimum altitude. Chase the optimum altitude. • Flying at the cross-over altitude is faster, but costs fuel. • Step Climb around the optimum altitude (see FCOM). • Avoid delays in initiating a step climb. • For short stage lengths, fly at an appropriate altitude (see FCOM). • Wind variations with altitude can give advantages in flying at lower altitudes. 6.2.5 DESCENT • Diminishing descent speed can allow significant fuel savings. • Avoid early descents Getting to grips with Fuel Economy 6 - DETAILED SUMMARY - 73 - 6.2.6 HOLDING • The best combination for fuel burn is clean configuration at green dot speed. • Manoeuvrability, speed or ATC restrictions may require a hold in configuration 1 at S speed. • If holding is to be anticipated, linear holding saves fuel. 6.2.7 APPROACH • Avoid extending gear unnecessarily early. 6.3 FUEL SAVINGS The following table gives examples of the savings possible through the application of correct procedures and practices. The values represent typical saving as there is variation dependant on the actual base case considered. However these figures serve to illustrate the magnitude of savings being achieved (or penalties being paid). The savings are expressed in kg of fuel for one flight, with the sector length being representative for each aircraft. Fuel Savings Possible in the Pre-Flight phase Item Variation A300 A310 A320 A330 A340- 200/300 A340- 500/600 Sector 2000nm 2000nm 1000nm 4000nm 6000nm 6000nm CG mid to aft 710 330 0 600 900 1550 Weight -1% MTOW 380 250 100 800 1530 1920 EO Taxi 8 minutes 50 40 25 50 50 70 APU 3 min Grd Power 9 9 6 10 10 14 Ground Idle 3 min APU 18 18 9 15-24 3 9 Misrigged Slat 15mm to zero 90 90 60 270 270 270 Peeling Paint 1sq m slat to zero 12 12 8 60 60 60 7 – CONCLUSIONS Getting to grips with Fuel Economy - 74 - Fuel Savings in the In Flight Phase Item Variation A300 A310 A320 A330 A340- 200/300 A340- 500/600 Sector 2000nm 2000nm 1000nm 4000nm 6000nm 6000nm TO Conf Max to min F/S 15 15 10 24 - 50 Climb Rating Derate 2 to full Climb NA NA NA 30 120-320 445 Climb Speed 330 to 300kias 10 15 70 35 25 -10 Cruise Altitude Optimum to –2000’ 65 80 80 100 95 135 Cruise Altitude Optimum to +2000’ 90 60 25 145 30 25 Cruise Mach Mecon+.01 to Mecon 230 430 40 330 900 2540 Delayed Climb CFP to 500nm late 240 220 180 330 390 340 CG mid to aft 710 330 0 600 900 1550 Descent Speed Max to 300kt 35 40 30 70 75 100 Early Descent CFP to 2min early 70 70 50 80 95 135 Hold Green Dot Clean Conf 190 135 30 205 230 130 Getting to grips with Fuel Economy 6 - DETAILED SUMMARY - 75 - 6.4 ECONOMIC BENEFITS It may be that 5 or 10 kg extra fuel per flight does not seem significant in terms of the total fuel burn during the flight. However this saving accumulates with every flight. Sometimes the savings for an A340 seem worthwhile compared with the equivalent value for an A320, but the increased number of flight cycles for an A320 can make this saving more significant than that of the A340. The only way to assess the impact of any saving is to look at it over a given time span. The economic impact calculations have assumed typical yearly utilisation rates, average sector lengths and sectors per year as follows: The following table shows the annual cost savings for one aircraft associated with various fuel savings for each Airbus type based on the above utilisation figures. Fuel is assumed to cost $1/us gallon (33cents/kg). Utilisation A300 A310 A320 A330 A340 Flying Hours/year 2600 3200 2700 2900 4700 Average sector - nm 2000 2000 1000 4000 6000 Average flight time - hr 4.5 4.6 2.4 8.5 13.8 No of sectors/year 580 700 1125 340 340 Savings/flight A300 A310 A320 A330 A340 10kg $1920 $2310 $3720 $1120 $1120 50kg $9600 $11550 $18600 $5600 $5600 250kg $48000 $57750 $93000 $28000 $28000 1000kg $192000 $231000 $372000 $112000 $112000 7 – CONCLUSIONS Getting to grips with Fuel Economy - 76 - 7. CONCLUSIONS There are many factors that influence the fuel used by aircraft, and these are highlighted in this report. The unpredictability of fuel prices, together with the fact that they represent such a large burden to the airline has prompted Airbus to be innovative in the field of fuel conservation. The relationship between fuel used and flight time is such that sometimes compromise is necessary to get the best economics. Whether in the field of design engineering or in flight operations support, we have always maintained a competitive edge. Whether it is in short or ample supply, we have always considered fuel conservation a subject worth revisiting. Fuel conservation affects many areas including flight planning, flight operations and maintenance. Airbus is willing and able to support airlines with operational support in all the appropriate disciplines. Despite the increasing efficiency of modern aircraft it is a subject that demands continuous attention and an airline that can focus on the subject, together with the Operation Support of Airbus is best placed to meet the challenges of surviving and profiting in the harsh airline environment of the 21st century. Getting to grips with Fuel Economy 8 - APPENDIXES - 77 - 8. APPENDICES These appendices contain climb and descent graphs for some of the other variants of Airbus aircraft. Each airframe/engine combination have different characteristics. Even the weight variant can influence these characteristics. It is therefore impossible to include all variants, but the selection shown will give an idea of the sensitivities of fuel burn and time to technique. 8 - APPENDICES Getting to grips with Fuel Economy - 78 - APPENDIX A (CLIMB CHARTS) The climb chart for the A300 is given in the main report (5.2.3) The A310 shows similar characteristics and is shown below. Note that the lower mach numbers (0.76, 0.78 and 0.8) show no variation. The main report gives the climb chart for the A320 which is similar to the A318 and A319. The A321 however shows more significant differences. Effect of Climb Technique on fuel and time to 130nm A310-324 ISA F/L 350 Weight 130000kg -6.00% -4.00% -2.00% 0.00% 2.00% 4.00% 6.00% -1.00% 0.00% 1.00% 2.00% 3.00% 4.00% Fuel - % Time % FMGS 280 300 320 330 Climb Speed kias 270 100kg 1 minute M 0.82 Effect of Climb Technique on fuel and time to 230nm A321-211 ISA F/L 350 Weight 80000kg -6.00% -4.00% -2.00% 0.00% 2.00% 4.00% 6.00% -2.00% -1.00% 0.00% 1.00% 2.00% 3.00% 4.00% 5.00% 6.00% Fuel % Time % M No FMGS 0.76 0.8 100 kg 1 minute 0 100 Getting to grips with Fuel Economy 8 - APPENDIXES - 79 - The A330 aircraft show characteristics similar to the A321 and an example is shown below. The A340-200/300 series show characteristics approaching that of the A340-500/600 but still shows minimum fuel at a speed lower than max, unlike the A340-500/600 (see 5.2.3). Effect of Climb Technique on fuel and time to 220nm A340-313E ISA F/L 350 Weight 240000kg -6.00% -4.00% -2.00% 0.00% 2.00% 4.00% 6.00% -1.00% 0.00% 1.00% 2.00% 3.00% Fuel % Time % M No FMGS 0.76 0.78 0.8 280 300 320 340 Climb Speed kias 0.82 270 100kg 1 minute Effect of Climb Technique on fuel and time to 150nm A330-343 ISA F/L 350 Weight 190000kg -6.00% -4.00% -2.00% 0.00% 2.00% 4.00% 6.00% -1.00% 0.00% 1.00% 2.00% 3.00% Fuel % Time % M No FMGS 0.8 0.76 280 300 320 340 Climb Speed kias 0.82 270 100 kg 1 minute 0 100 8 - APPENDICES Getting to grips with Fuel Economy - 80 - APPENDIX B (DESCENT CHARTS) The A300 shows similar characteristics to the A310 in the main report. The A320 shown below has similar characteristics to the A318, A319 and A321. Effect of Descent Technique on Fuel and Time for 115nm A300B4-605R ISA Weight 120000kg 17.5 18.0 18.5 19.0 19.5 20.0 20.5 21.0 21.5 22.0 250 300 350 400 450 500 550 600 Fuel - kg Time - min 240 250 260 300 320 330 6 28 50 72 100 390 370 350 330 310 Initial Flight Level Cost Index Descent Speed KIAS Effect of Descent Technique on Fuel and Time for 120nm A320-214 ISA Weight 60000kg 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 200 250 300 350 400 450 Fuel - kg Time - min 240 250 260 300 320 340 0 24 36 50 80 390 370 350 330 310 Initial Flight Cost Index Descent Speed KIAS 280 9 Getting to grips with Fuel Economy 8 - APPENDIXES - 81 - The following shows an example of an A330: Most of the A340’s have similar speed characteristics to the A340-642 shown below. The A340-200 does however show an improvement in fuel for speeds lower than 260kts. Effect of Descent Technique on Fuel and Time for 160nm A330-343 ISA Weight 180000kg 24.0 25.0 26.0 27.0 28.0 29.0 30.0 500 600 700 800 900 1000 1100 Fuel - kg Time - min 240 250 260 300 320 340 48 310 390 370 I3n5i0tial Flight Le3v3e0l Cost Index Descent Speed KIAS 280 30 CI=0 270kias CI=60 315kias CI=100 315kias Effect of Descent Technique on Fuel and Time for 160nm A340-642 ISA Weight 270000kg 24.0 25.0 26.0 27.0 28.0 29.0 30.0 700 800 900 1000 1100 1200 1300 1400 1500 1600 Fuel - kg Time - min 240 250 260 300 320 340 78 310 370 350 330 390 Initial Flight Level Cost Index Descent Speed KIAS 280 21 CI=0 272kias CI=100 308kias作者: sunenjoy 时间: 2010-8-25 21:38:19