航空论坛_航空翻译_民航英语翻译_飞行翻译

 找回密码
 注册
搜索
查看: 1945|回复: 1
打印 上一主题 下一主题

Checklist MS FSX incl. PMDG 747-400(F) 检查单 [复制链接]

Rank: 9Rank: 9Rank: 9

跳转到指定楼层
1#
发表于 2010-8-22 11:10:25 |只看该作者 |倒序浏览
游客,如果您要查看本帖隐藏内容请回复
附件: 你需要登录才可以下载或查看附件。没有帐号?注册

Rank: 9Rank: 9Rank: 9

2#
发表于 2010-8-22 11:11:25 |只看该作者
Checklist MS FSX incl. PMDG 747-400(F)
Member-#: _____________________
IVAO:
Website-PW: _____________________
Network-PW: _____________________
PMDG Options Menu / Various: Ground Air/Power Available should bet set to on
Attention:
If not: Bring forward APU start (instead of Ext Pwr On)
• Load & Fuel (at Configurator) Set
Parking Position / Preparation:
• Flighplan Create a flightplan (in FSBuild and save at PMDG dir.)
• FSX Start & load/create 747-flight
• Dark & Cold Load D&C panel setting
• Load & Fuel (at FSX) Check (or reset)
• Parkingbreak Set
• Dark & Cold (at Configurator) Load
• IVAP-Connection Activate
• Dep-Metar Check & note
• Arr-Metar Check & note
• Door(s) Open
• Gangway Enable (if available) (Ctrl + J)
 OVHP only:
• Battery On
• Standby Power Auto
• Bus Tie switches Auto
• GENerator CONTrol switches On
• Hydraulic Demand pump switches 1-3 Off
• Hydraulic Demand pump switch 4 Aux
• Engine hydraulic pump selectors On
• Ext Pwr 1 switch On (if available) (needs parking break to be set)
• Ext Pwr 2 switch On (if available) (needs parking break to be set)
• Panel lights
o CKT BKR OVHD PANEL On (if needed)
o GLARESHIELD PANEL/FLOOD On (if needed)
o DOME On (if needed)
• Elec Eng Control switches Norm & saved
• Utility (power switch) Left On
• Utility (power switch) Right On
• Lights
o NAV On (mandatory)
o LOGO On
o WING On
• Emergency Light Arm
• IRS Alignment (OVHP & FMC):
o IRS switches (1-3) Off
o IRS switches (1-3) Nav
o IRS switches (1-3) Align
o  FMC:
 Ident page 1L
 Pos Init page 6R
 Copy GPS Position 4R (alternative enter 4-letter airport code & press 2L)
 Paste to IRS Pos. 5R (alternative copy airport position to IRS; 2R  4R)
o IRS switches (1-3) Nav
• Fuel Pumps Off (CTR, STAB, MAIN 1 and 4, OVRD & MAIN 2 and 3)
• Fuel X-Feed On (4 switches)
• Nacelle Anti-Ice Off
• Wing Anti-Ice Off
• Window Heat Enable
• Yaw Dampers On
• APU switch Start
---wait till APU Gens available---
• APU Gen Switches 1 & 2 On
• PASSenger TEMPerature Auto
• FLT DECK (temperature) Auto
• Trim Air On
• Upper Recirculation Fan On (Upr Recirc)
• Lower Recirculation Fan On (Lwr Recirc)
• Gasper On
• Pack switches (1-3) Norm
• ISLN switches L & R Open (“Valve” extinguished)
• APU Bleed (abv Eng Bleed) On
End OVHP only
• FMC
- Clear messages  CLR
- Route Page RTE
- Enter company route [read: enter flightplan-name (created in FSBuild)]  3R
- Activate  6R  Exec
- Performance initialization page  6R
- Enter FL / altitude  1R (max FL for 747 = FL410)
- Gross Weight auto function  1L
- Enter fuel reserve in %  4L
- Enter Cost Index (50 to 100)  5L
- Thrust Limit page  6R
- Modify Thrust settings if needed
- Takeoff page  6R
- Enter flaps setting (standard 20)  1L
- Verify V1, VR and V2  1R  2R  3R (remember V2 speed)
- Verify takeoff trim settings  4R (remember trim number)
-
• IVAP-flightplan Read from FMC & note/enter in IVAP FP
• Speed at flightplan Enter TAS (calculate: KIAS + FL/2) or MACH
• Departure Time Enter (UTC to CET  CET -2 (winter -1))
• EFIS-Mode (MainPanel/MP) MAP
• EFIS-Range (MP) 40nm (or as required)
• GND-Control Set frequency (active ATC or Unicom 122.8)
• IFR-clrc Request (when ATC active)
• FP-correction Correct (if required / requested)
• IFR-clrc-data Note (Squawk, First-Altitude, QNH  Readback)
• Squawk Set
• Altimeter Set to actual atmospheric pressure (B)
• F/D (AP) On
• V2 (AP) Enter V2 speed to IAS/MACH indicator of AP
• LNAV (AP) Arm
• VNAV (AP) Arm
• First Alt (AP) Set
• AP Disengage Bar Up
• Fuel Control Switches (TP) Cutoff (Throttle Panel)
• Trim settings (TP) Check (same as FMC) (NUM1/7 with NUM off)
• Autobreak RTO
• TCAS switch Stby/Test
---wait till TCAS test finished---
• TCAS switch TA/RA
• TCAS biasing mode Above
• No Smoking On (or Auto)
• Seat Belts Auto
• FLT DK Door Lock
• TFC button (EFIS) Press (and check potential traffic)
---open Overhead panel & EICAS panel---
• Fuel Button (EICAS) Press & check fuel
• Fuel pumps On (all fuel pumps of tanks containing fuel)
---wait till fuel pumps rdy (green light)---
• Xfeed Set
o Tank 2 > Tank 1 Xfeed 1 on
o Tank 3 > Tank 4 Xfeed 2 on
o Otherwise Xfeed off
• Gangway disable (strg + j)
Engine s/u & Pushback:
• Doors closed
• Engine s/u & Pushback p/b clrc request
• Beacon Light On
• Hydraulic Demand pump switches 1-3 Auto
• Hydraulic Demand pump switch 4 Aux (check)
• Pack 1 On
• Pack 2 & 3 Off
• Engine Bleed Air switches On
• EICAS Open Engines Page
• EICAS Clear EICAS messages (Cacl Btn.)
• Parking break Off
• Pushback Start
• Engine Start Procedure:
o Autostart:
 Autostart On
 Continuous Ignition On
 Fuel Control Swt. 1 – 4 Run
 Engine 1 & 4 Start Sel. Pull
---wait till Engine 1 & 4 back at idle---
 Engine 2 & 3 Start Sel. Pull
o No Autostart:
 Autostart Off
 Continuous Ignition On
 Engine 1 & 4 Start Sel. Pull
---wait till N2% RPM reaches magenta line (14%)---
 Fuel Control Swt. 1 & 4 Run
---wait till Engine 1 & 4 back at idle---
 Engine 2 & 3 Start Sel. Pull
---wait till N2% RPM reaches magenta line (14%)---
 Fuel Control Swt. 2 & 3 Run
• APU Off
• APU Bleed Air Off
• Packs Norm (all)
• Hydraulic Demand pump switch 4 Auto
• Engine & Wing anti-ice On (under 10°C TAT)
• Main Display Check for warnings
• Taxi Lights On
• Flaps Select (as filled in FMC)
• Pushback Finish
• Taxi-Clrc Request
Taxi:
• Taxiways Note (if needed)
• Ground-Guidance Request (if needed)
• Hand-off GND to TWR Change frequency
h/p:
• l/u & t/o clrc Request (rdy for dep h/p xx)
• Landing Lights On
• Strobe Light On
• IVAP-Transponder On
• Postion & hold Taxi & stop on rwy
• Parkingbreak Set
Ready to Takeoff:
• Autothrottle (AP) On
• AP settings Check (FD on, HDG, IAS, LNAV, VNAV)
• Thrust Levers Forward
---wait till 70% N1---
• Parkingbreak Release
• TO/GA button Press (the screw over the F/D switch)
• Yoke Press forward till 80kts
• V1 Abort of start not possible anymore
• VR Lift nose up
• V2 Lift-off
• Trim settings Adjust (when needed)
Takeoff:
• Gear Up (at positive climb rate >500ft)
• Autopilot On (1 of 3)
• Flaps Raise (on schedule, see PFD)
• Landing gear lever Off position
• Airborne Publish airborne when on Unicom (no ATC)
• Start time Note (if needed)
• Hand-off TWR to APP(DEP) Change frequency
• Landing-/Taxi Lights Off
Climb:
--- to final FL / next FL clrc ---
• AP altitude (& speed) Change (Selected Mode if needed)
• TCAS biasing mode N
---do the following things if required---
• Hand-off APP to CTR Change frequency
• Engine & Wing anti-ice On (under 10°C TAT)
• Altimeter Readjust (above 18000ft)
• Radio /ATC contact Maintain (on UniCom watch TCAS)
Cruise:
• Autopilot / FMC Check permanently
o FMC Check PROGress page for fuel consumption
---when center tanks (center/stab) empty---
• Center / stab fuel pump Off
---when inner wing tanks have reached same fuel load as outer wing tanks---
• Xfeed Off
• Descent preparations Begin 30nm before T/D (Top of Descent)
Descent & Approach:
• Airport-/Meta-Information Retrieve
• Autobreaks Set
• FMC:
o Arrivals page  DEP/ARR
o Set active rwy (and approach/STAR)
o Approach Ref page  INIT REF button
o Copy flap and corresponding Vref setting  1R or 2R
o Paste for approach  4R
o Note approach speed (see 4R)
o NAV Radio page  NAV/RAD
o Note rwy heading (see 4L)
o Close FMC
• Start of Descent (4 possibilities):
o VNAV:
 Alt (AP) Set (before reaching T/D !)
 VNAV Will descent automatically at T/D
o DES NOW:
 Alt (AP) Set (before reaching T/D !)
 FMC ACT ECON CRZ page  VNAV
 Page 2 Next Page
 Des Now 6R
 Execute EXEC
o FL CH:
 Alt (AP) Set
 FL CH (AP) On
 Speed (AP) Set to IAS, set Speed
o Change Cruise Alt:
 FMC ACT ECON CRZ page  VNAV
 Alt (FMC) Enter in Scratchpad
 Cruise Alt (FMC) Set  1L
 Execute EXEC
• TCAS Biasing mode Below
• Speedbrakes Up (when needed/too fast)
• Altimeter Readjust (under 18000ft)
• Hand-off CTR to APP Change frequency
• Landing lights On
• Taxi light On
• Flaps Lower (as indicated on PFD) (e.g. 1 passes by set to 5)
Final approach & Landing (Autoland):
• Gear Down (under 270kt / at flap 20)
• Speedbrake Arm
---stabilize von glideslope---
• ILS captured Announce (on Unicom state final app)
• LOC (AP) On (to follow ILS localizer)
• APP (AP) On (to follow glideslope)
---check, when APP pressed, LOC, VNAV off, 3 AP on---
• Hand-off APP to TWR Change frequency
• Landing clrc Request (or state intention on Unicom)
---Touchdown---
• Throttles Idle
• Thrust reversers Engage (if needed)
• Thrust reversers Disengage (at 80kt) (Throttles idle)
• Autopilot (AP) Dienagage
• A/T (AP) Off
• F/D (AP) Off
• Runway Vacate („rwy vacated“)
• Flaps Lower (as indicated on PFD) (e.g. 1 passes by set to 5)
Final approach & Landing (w/o Autoland):
• Gear Down (under 270kt / at flap 20)
• Speedbrake Arm
---stabilize von glideslope---
• ILS captured Announce (on Unicom state final app)
---check flaps to ref-degree and gear down---
• Hand-off APP to TWR Change frequency
• Autopilot (AP) Disengage (Disengage bar down)
• A/T (AP) Off
• F/D (AP) Off
• Trim settings Adjust (when needed)
• Landing clrc Request (or state intention on Unicom)
---Touchdown---
• Throttles Idle
• Thrust reversers Engage (if needed)
• Thrust reversers Disengage (at 80kt) (Throttles idle)
• Runway Vacate („rwy vacated“)
• Transponder Stdby
Taxi:
• Hand-off TWR to GND Change frequency
• Taxiways Note and follow (with active ATC)
• ( Ground-Guidance Request if required)
• Flaps Set 0
• Speedbrake Disengage (if engaged)
• Autobrakes Off
• Landing lights Off
• Strobe Off
• Landing time Note (if needed)
• APU Start
• Parking brake Set
Parking Position:
• ATC contact End (state “on blocks, thx for service, bye”)
• APU Gen 1 & 2 On
• APU Bleed On
• Engine Bleed Off
• Engine hydraulic pumps Off
• Fuel control switches Cutoff
• Seatbelts Off
• Door s Open (shift + e)
• Gangway Enable (strg + j)
• Beacon lights Off
---Aircraft ready for turn-around /next flight---
---Continue if Cold&Dark needed---
• Ground power On (if available)
• APU bleed Off (if Ground power available)
• APU Off (if Ground power available)
• Yaw Dampers Off
• Hydraulic Demand switches Off
• Continuous Ignition Off
• Autostart Off
• IRS systems 1-3 Off
• Utility L & R Off
• Fuel pumps Off (all)
• XFeeds On (all)
• Window heat Off
• Engine & Wing anti-ice Off
• AFT Cargo HT(heat) Off
• Trim Air Off
• Gasper Off
• UPR RECIRCulation fan Off
• LWR RECIRCulation fan Off
• Packs 1-3 Off
• ISLN switches L & R Off
• GENerator CONTrol switches Off
• TCAS Stdby
• If still on APU (no Ground power):
o APU bleed Off
o APU Gen 1 & 2 Off
o APU Off
• Ground power Off
• External lights Off (all)
• Internal lights Off (all)
• Bus Tie Switches Off
• Stdby power selector Off
• Battery Off
Checklist for PMDG 747X with Microsoft Flight Simulator.
Created by: Carsten Rau (June2008 / v5)
I used to create: PMDG Manual, Michael Swannick’s B744 Checklist, Jared Smith’s 744 Guide
Only use with: Microsoft Flight Simulator / IVAO (Intl. Virtual Aviation Organization)
Visit: http://www.ivao.aero
http://www.carstenrau.de
http://www.leveldsim.com - Level-D 767
http://www.precisionmanuals.com - PMDG 747
http://www.wilcopub.com - Wilco 737 PIC / Airbus Series 1 & 2
Attachments
for
Checklist MS FSX incl. PMDG 747-400(F)
by Carsten Rau
Note: The graphic above represents Flight Plan Fuel
Upper & Lower graphics available for free at only.
http://www.precisionmanuals.com (747 manual)
Basic Operating Weight (OEW) 394.000 LBS
Fuel planning notes:
= Zero Fuel Weigh (ZFW) XXX.XXX LBS (max 535.000 LBS)
+ Payload (passengers & cargo) XXX.XXX LBS
+ Minimum Landing Fuel 024.000 LBS
+ Alternate Fuel (200nm distance) 018.000 LBS
= Planned Landing Weight (PLW) XXX.XXX LBS (max 630.000 LBS)
+ Contingency Fuel (holding, taxi, etc.) 018.000 LBS
= Planned Takeoff Weight (PTOW) XXX.XXX LBS (max 875.000 LBS)
+ Flight Plan Fuel (fuel for route) XXX.XXX LBS
Flight Plan Fuel + 60.000 LBS = Total Fuel
 Total fuel = Enough fuel for route, 1h contingency (holding & taxi), problematic winds, alternate fuel for 200nm and a minimum landing fuel (1h+). Modify alternate value as needed.
 Load all wing tanks with same amount of fuel; outer tanks full  inner tanks  center tanks.
Recommendation:
Print pages 2-1 to 2-16 (Cruise / Fuel) & 3-1 to 3-7 (Landing) from 747 manual.

使用道具 举报

您需要登录后才可以回帖 登录 | 注册


Archiver|航空论坛 ( 渝ICP备10008336号 )

GMT+8, 2024-11-23 17:57 , Processed in 0.024001 second(s), 13 queries .

Powered by Discuz! X2

© 2001-2011 MinHang.CC.

回顶部