|
IATA Dangerous Goods Regulations
52nd Edition (English)
Effective 1 January 2011
ADDENDUM
Posted 30 December 2010
Users of the IATA Dangerous Goods Regulations are asked to note the following amendments and corrections to the 52nd Edition, effective from 1 January 2011.
Where appropriate, changes or amendments to existing text have been highlighted (in yellow - PDF or grey - hardcopy) to help identify the change or amendment.
New or Amended State Variations (Section 2.8.2)
Amend SAG (Saudi Arabia)
Amend SAG-03
SAG-03 Name, address and telephone number of consignee must be written in full on the Air Waybill as well as the package of for dangerous goods to any destination in Saudi Arabia.
Add New SAG-06
SAG-06 Name, address, and telephone number of consignee must be written in full on each package of dangerous goods shipments to any destination in Saudi Arabia.
New or Amended Operator Variations (Section 2.8.4)
Amend 9S (Southern Airlines)
9S-01 Class 7, Radioactive Materials will not be accepted for carriage outside the USA (see 10.10.2). Not used.
Amend AA (American Airlines)
Add new
AA-06 Division 6.2 Category A, infectious substance affecting animals (UN 2900) and humans (UN 2814) will not be accepted for carriage (see PI 620).
New AB (Air Berlin)
AB-01 Class 7, Radioactive material, fissile material and excepted packages will Not be accepted on AB Flights (see 10.5.8, 10.5.13)
AB-02 Packages allowed on Cargo Aircraft Only or prepared according to packing instructions for Cargo Aircraft Only (CAO) are not allowed on AB Flights.
Amend MS (Egyptair)
MS-01 The transport of dangerous goods on board EGYPTAIR NETWORK must comply with the following:
1. The name, address and telephone number of the shipper/consignee must be written in full on the air waybill and on the package(s).
2. The shipper of any dangerous goods must provide a written undertaking to re-ship the consignment at the shipper's cost and risk if the consignment is not cleared, or fully received by the consignee, within fifteen (15) working days from the arrival of the consignment.
Amend OU (Croatia Airlines)
OU-04 Dangerous goods in Limited Quantities (“Y” packing instructions) will not be accepted for carriage, except for Consumer commodity (ID 8000) (see Subsection 2.7 and all “Y” Packing Instructions).
OU-16 Biological substances, Category B UN 3373 (human or animal) will only be accepted if assigned to UN 2814 or UN 2900 as appropriate from approved Croatia Airlines customers. For additional information contact Croatia Airlines Cargo Sales Department.
The only exceptions to this variation are:
. any tissues or organs intended for use in human or animal transplantation;
. pathogen-free blood or blood components collected for transfusion or for the preparation of blood products to be used for human or animal transfusion or transplantation.
In these cases, the air waybill must bear a detailed description to enable identification as non regulated material (see Packing Instruction 620 and 8.2).
Amend QT (TAMPA Cargo)
QT-01 Dangerous goods in excepted quantities will not be accepted for carriage (see Subsection 2.6) Not used.
Amend SV (Saudi Arabian Airlines)
SV-10 Not used. Battery-powered wheelchairs or mobility-aids with spillable batteries will not be accepted on SVA aircraft as checked baggage (see 2.3.2.3 and 9.3.16).
Add new
SV-13 The shipper must provide a 24-hour emergency telephone number of a person / agency who is knowledgeable of the hazards, characteristics and actions to be taken in the case of an accident or incident concerning each of the dangerous goods being transported. This telephone number, including the country and area code, preceded by the words "Emergency Contact" or "24-hour number", must be inserted on the DGD, preferably in the "Handling Information" box, e.g. Emergency Contact +47 67 50 00 00 (see 8.1.6.1 1 and 10.8.3.1 1).
A 24-hour emergency telephone number is not required for shipments that do not require a Shipper’s Declaration for Dangerous Goods.
Section 2
Page 30 – Amend 2.7.2.1(g) as shown:
(g) Class 9: Only Dibromodifluoromethane (UN 1941), Benzaldehyde (UN 1990), Ammonium nitrate fertilizers (UN 2071), Environmentally hazardous substance, solid, n.o.s. (UN 3077), Environmentally hazardous substance, liquid, n.o.s. (UN 3082), Chemical kit or First aid kit (UN 3316), Aviation regulated liquid, n.o.s. (UN 3334), Aviation regulated solid, n.o.s. (UN 3335) of Class 9 substances.
Page 31 – Amend 2.7.2.2(j) as shown:
(j) Class 9: Miscellaneous dangerous goods except Dibromodifluoromethane (UN 1941), Benzaldehyde (UN 1990), Ammonium nitrate fertilizers (UN 2071), Environmentally hazardous substance, solid, n.o.s. (UN 3077), Environmentally hazardous substance, liquid, n.o.s. (UN 3082), Chemical kit or First aid kit (UN 3316), Aviation regulated liquid, n.o.s. (UN 3334), Aviation regulated solid, n.o.s. (UN 3335).
Section 3
Page 132 – Amend 3.9.2.4 as shown:
3.9.2.4 Environmentally Hazardous Substances
Environmentally Hazardous substances (aquatic environment) are those that meet the criteria in 2.9.3 of the 15th revised edition of the UN Model Regulations or that meet criteria in national or international regulations established by the appropriate national authority in the State of origin, transit or destination. The detailed classification categories and criteria for environmentally hazardous substances (aquatic environment) as set out in 2.9.3 of the 15th revised edition of the UN Model Regulations can be found at http://www.iata.org/whatwedo/cargo/dangerous_goods/index.htm
Substances or mixtures dangerous to the aquatic environment not presenting a danger covered by other classes, must be assigned to packing group III and designated:
. UN 3077 Environmentally hazardous substance, solid, n.o.s.; or
. UN 3082 Environmentally hazardous substance, liquid, n.o.s.
Section 4
Table 4.2: Revise the entries as shown:
UN/ ID no.
Proper Shipping Name/Description
Class or Div.
(Sub Risk)
Hazard Label(s)
PG
EQ see 2.7
 assenger and Cargo Aircraft
Cargo Aircraft Only
S.P. see 4.4
ERG Code
Ltd Qty
Pkg Inst
Max Net Qty/Pkg
Pkg Inst
Max Net Qty/Pkg
Pkg Inst
Max Net Qty/Pkg
A
B
C
D
E
F
G
H
I
J
K
L
M
N
2071
Ammonium nitrate fertilizers
9
Miscellaneous
III
E1
Y958
30 kg G
958
200 kg
958
200 kg
A89 A90
9L
1549
Antimony compound, inorganic, solid, n.o.s. .
6.1
Toxic
III
E1
Y645
10 kg
670
100 kg
667 677
200 kg
A12
6L
3334
Aviation regulated liquid, n.o.s. . .
9
Miscellaneous
III
E1
Y964
30 kg G
964
100 L
964
220 L
A27
9A
3335
Aviation regulated solid, n.o.s. . .
9
Miscellaneous
III
E1
Y956
30 kg G
956
100 kg
956
200 kg
A27
9A
3054
Cyclohexyl mercaptan
3
Flamm. liquid
III
E1
Y344
10 L
355
60 L
365 366
220 L
3L
1597
Dinitrobenzenes, liquid
6.1
Toxic
II III
E4 E1
Y641 Y642
1 L 2 L
654 655
5 L 60 L
662 663
60 L 200 L 220 L
A3
6L 6L
3450
Diphenylchloroarsine, solid
6.1
Toxic
I
E0
Forbidden
Forbidden
673
15 kg 50 kg
6L
3245
Genetically modified micro-organisms
9
Miscellaneous
E0
Forbidden
959
No Limit
959
No Limit
A47
9L
3245
Genetically modified organisms
9
Miscellaneous
E0
Forbidden
959
No Limit
959
No Limit
A47
9L
2481
Ethyl isocyanate
6.1 (3)
Forbidden
Forbidden
Forbidden
A174
3P
6F
2483
Isopropyl isocyanate
6.1 (3)
Forbidden
Forbidden
Forbidden
A174
6F
6H
3249
Medicine, solid, toxic, n.o.s.
6.1
II III
E4 E1
Y644 Y645
1 kg 5 kg 10 kg
669 670
25 kg 100 kg
676 677
100 kg 200 kg
A3 A801
6L 6L
3208
Metallic substance, water-reactive, n.o.s. .
4.3
Dang. when wet
I
E0
Forbidden
Forbidden
487
15 kg
A3
4W
II III
E2 E1
Y475 Y476 Y477
5 kg 10 kg
483 485
15 kg 25 kg
489 491
50 kg 100 kg
4W 4W
3290
Toxic solid, corrosive, inorganic, n.o.s. .
6.1 (8)
Toxic & Corrosive
I
E5
Forbidden
665
1 kg
672
25 kg 15 kg
A5
6C
II
E4
Y644
1 kg
668
15 kg
675
50 kg
6C
2928
Toxic solid, corrosive, organic, n.o.s. .
6.1 (8)
Toxic & Corrosive
I
E5
Forbidden
665
1 kg
672
25 kg 15 kg
A5
6C
II
E4
Y644
1 kg
668
15 kg
675
50 kg
6C
Section 5
Page 384 – Revise packing instruction 202 as shown:
(i) Open cryogenic receptacles must bear the following marks permanently affixed e.g. by stamping, engraving or etching:
. the manufacturer’s name and address;
. the model number or name;
. the serial or batch number;
. the UN number and proper shipping name of gases for which the receptacle is intended;
. the capacity of the receptacle in litres.
Note: The marking on open cryogenic receptacles will become mandatory with effect 1 January 2012 for open cryogenic receptacles manufactured after 1 January 2012. The size of the marking must be as set out for cylinders in 6.4.2.7.1. Open cryogenic receptacles manufactured prior to 1 January 2012 are not required to be so marked.
(j) Open cryogenic receptacles are permitted for argon, krypton, neon, nitrogen and xenon refrigerated liquids.
Page 412 – Revise Packing Instruction 377 as shown:
OUTER PACKAGINGS
Type
Drums
Boxes
Desc.
Steel
lywood
Fibre
lastic
Steel
Wood
lywood
Recon-stituted wood
Fibreboard
lastic
Spec
1A2
1D
1G
1H2
4A
4C1 4C2
4D
4F
4F 4G
4H1 4H2
Page 422 – Revise Packing instruction 454 as shown:
Additional Packing Requirements
. each reel must be placed in a tightly closed metal or strong cardboard or fibreboard inner packaging with a cover held in place by adhesive tape or paper;
. packagings must meet Packing Group II performance standards;
. fibre drums (1G) may only contain 600 m of film.
Single packagings are not permitted.
Page 449 – Revise Packing Instruction 492 as shown:
COMBINATION PACKAGINGS
UN Number
Total quantity per package passenger aircraft
Total quantity per package Cargo Aircraft Only
UN 3292, Batteries, containing sodium
Batteries may be offered for transport and transported unpacked or in protective enclosures such as fully enclosed or wooden slatted crates that are not subject to the requirements of Section 6
Forbidden
No limit
UN 3292, Cells, containing sodium
25 kg G
25 kg No limit
Page 468 – Revise Packing Instruction 565 as shown:
Additional Packing Requirements
Oxygen generator, chemical containing oxidizing substances, including when fitted in associated equipment e.g. passenger service units (PSUs), protective breathing equipment (PBE) etc, must meet all the following conditions:
(a) the generator, without its packaging, must be capable of withstanding a 1.8 m (6 ft) drop test onto a rigid, non-resilient, flat and horizontal surface in the position most likely to cause actuation without loss of its contents and without actuation. For PBE, which are in a vacuum-sealed bag as part of their containment system, this test may be conducted on the PBE in the vacuum-sealed bag;
(b) when a generator is equipped with an actuating device it must have at least two positive means of preventing unintentional actuation For PBE, which are in a vacuum-sealed bag as part of their containment system, the vacuum-sealed bag may be considered the second positive means of preventing unintentional actuation. For oxygen generators, indicative methods of preventing unintentional activation are as follows:
1. mechanically actuated devices:
(i) two pins, installed so that each is independently capable of preventing the actuator from striking the primer;
(ii) one pin and one retaining ring, each installed so that each is independently capable of preventing the actuator from striking the primer; or
(iii) a cover securely installed over the primer and a pin installed so as to prevent the actuator from striking the primer and cover.
2. electrically actuated devices: The electrical leads must be mechanically shorted and the mechanical short must be shielded in metal foil.
3. For PBE:
(i) a pin so as to prevent the actuator from striking the primer; and
(ii) placed in protective packaging such as a vacuum-sealed bag.
(c) the generator(s) must be transported in a package which will meet the following requirements when one generator in the package is actuated:
1. other generators in the package will not be actuated,
2. packaging material will not ignite, and
3. the outside surface temperature of the completed package will not exceed 100°C (212°F);
Note: To enable test (c) (1), (2) and (3) to be conducted on PBE, it is acceptable to break the vacuum-sealed bag to actuate the generator before placing in the package.
Page 497 – Revise Packing Instruction 681 as shown
OUTER PACKAGINGS
Type
Drums
Boxes
Desc.
Steel
lywood
Fibre
lastic
Steel
Wood
lywood
Recon-stituted wood
Fibreboard
lastic
Spec
1A2
1D
1G
1H2
4A
4C1 4C2
4D
4F
4F 4G
4H1 4H2
Page 518 – Revise Packing Instruction 876 as shown
OUTER PACKAGINGS
Type
Drums
Boxes
Desc.
Steel
lywood
Fibre
Plastic
Steel
Wood
Plywood
Recon-stituted wood
Fibreboard
Plastic
Spec
1A2
1D
1G
1H2
4A
4C1 4C2
4D
4F
4F 4G
4H1 4H2
Page 519 – PI 950, Revise Note to read:
Note:
Replacements for the dangerous goods permitted in paragraphs (b) and (c) (c) and (d) must not be carried under this packing instruction.
Page 524 – PI 956 Insert FX-06
Page 534 – PI 964 Insert FX-06
Page 535 – PI 964 revise as shown:
COMBINATION PACKAGINGS
Inner Packaging (see 6.1)
Net quantity per inner packaging
Glass
10.0 L
Metal
30.0 L 40.0 L
Plastic
40.0 L 30.0 L
Page 535 – PI Y964 Insert FX-06
Page 537 – Revise Packing Instruction 965 as shown:
Additional Requirements – Section I
. lithium ion cells and batteries must be placed in inner packagings that completely enclose the cell or battery then placed in an outer packaging. The completed package for the cells or batteries must meet the Packing Group II performance standards;
. lithium batteries with a mass of 12 kg or greater and having a strong, impact-resistant outer casing, or assemblies of such batteries, may be transported when packed in strong outer packagings in or protective enclosures. The packagings need not meet the requirements of Section 6 of these Regulations. The packagings must be approved by the appropriate authority of the State of origin. A copy of the document of approval must accompany the consignment;
. batteries manufactured after 31 December 2011 must be marked with the Watt-hour rating on the outside case.
Page 542 – Revise Packing Instruction 968 as shown:
Additional Requirements – Section I
. lithium metal cells and batteries must be placed in inner packagings that completely enclose the cell or battery then placed in an outer packaging. The completed package for the cells or batteries must meet the Packing Group II performance standards;
. lithium batteries with a mass of 12 kg or greater and having a strong, impact-resistant outer casing, or assemblies of such batteries, may be transported when packed in strong outer packagings in or protective enclosures. The packagings need not meet the requirements of Section 6 of these Regulations. The
packagings must be approved by the appropriate national authority of the State of origin. A copy of the document of approval must accompany the consignment.
Section 7
Page 595 Revise Figure 7.1.A as shown:
FIGURE 7.1.A
Limited Quantities Mark (7.1.5.3)
Name: Limited Quantity
Minimum dimensions: 100 mm × 100 mm
For small packages the dimensions may be reduced to not less than 50 mm x 50 mm provided the marking remains clearly visible
Minimum width of line forming the diamond: 2 mm
The symbol “Y” must be placed in the centre of the mark and must be clearly visible
Top and bottom portions and line must be black, centre area white or suitable contrasting background.
Section 8
Page 620 – 8.1.5 Insert FX-18
Page 632 – In Figure 8.1.I and Figure 8.1.J delete “III” from packing group column for UN 1845, Dry ice
Section 9
Page 644 – Revise 9.3.2.2.5 as shown:
9.3.2.2.5 Explosives of Division 1.4B must not be loaded with other explosives except for Division 1.4S. When loaded on the same aircraft with explosives other than Division 1.4S, Division 1.4B explosives must be loaded into separate unit load devices and when stowed aboard the aircraft, the unit load devices must be separated by other cargo with a minimum separation distance of 2 m. When not loaded in a unit load device Division 1.4B and other explosives must be loaded into different, non-adjacent loading positions and separated by other cargo with a minimum separation distance of 2 m.
Section 10
Page 721 – In Figure 10.8.E delete “III” from packing group column for UN 1845, Carbon dioxide, solid
Appendix A
Page 732 – Revise definition of Cargo as shown:
CARGO For the purposes of these Regulations, any property carried on an aircraft other than mail stores and accompanied or mishandled baggage.
Appendix D.1
Page 770 – Replace the contact details for Canada with the following:
Chief, Airspace Standards and Procedures
Transport Canada
Civil Aviation Directorate
Ottawa, Ontario
Canada K1A 0N8
Tel: +1 (613) 998-9855
Fax: +1 (613) 954-1602
E-mail: ron.carter@tc.gc.ca
Page 772 – Replace the contact details for Finland with the following:
Finnish Transport Safety Agency
Aviation (Finnish CAA)
P.O.Box 320
FI-00101 Helsinki
FINLAND
Tel: +358 (0)20 618 6050
Fax: +358 (0)20 618 500
E-mail: lentotoiminta@trafi.fi
website: www.trafi.fi or www.civilaviationauthority.fi
|
IP卡
狗仔卡
发表于 2011-6-19 11:56:58
分享
收藏
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
发表于 2011-8-13 23:19:43
