- 注册时间
- 2011-11-30
- 最后登录
- 2011-11-30
- 在线时间
- 0 小时
- 阅读权限
- 10
- 积分
- 0
- 帖子
- 2
- 精华
- 0
- UID
- 10954
|
Installation of the wheel & a, Q) ~/ n! Z9 g1 j, z* X
9 s' v# m$ f/ {/ }# X/ V(a) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces.
( Z$ u& c. D/ \ B! W; Z# i5 O. _0 u* j
(b) Install the wheel, with the valve outboard, with a handling tool. 7 t( z9 d ]4 W+ o
(c) Remove the PROTECTOR NLG (J47548)
: ?1 M1 z* z9 s% P: }( G; k" Y: u, |. E1 z7 {3 ~+ x
(d) Apply a light coat of Material No. 04-004* (COMMON GREASES) or Material No. 04-022* (COMMON GREASES) or Material No. 04-035* (COMMON GREASES) on the axle. ( }" [" Q2 D1 h3 L7 x% o, K7 `" }* E
/ L V' a% y; u4 R5 C5 U(e) Install the axle nut (10). 8 z. `$ f# [1 z3 c U: H; w
6 w3 P7 H9 K: ~! Y4 O$ M(f) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 21.80 m.daN (160.77 lbf.ft) with the ADAPTOR NLG (J47549) .
8 O: c0 F0 r0 P( o+ d; [, h
7 X9 N( j. Y; l5 H' J8 N, G% E# R(g) Prevent rotation of the wheel and loosen the axle nut (10). & O' Q4 ~8 D" Y, q# _" M! ~
8 c- ]) @/ e3 P# q B' f1 B, j" e
(h) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 10.85 m.daN (80.01 lbf.ft). / { s1 P; S1 s' b# N
v0 m U) n' @. V4 p' ^) i8 I(i) Tighten the axle nut (10) until the holes for the bolts (5) are aligned. ! w# Y, U- p7 i; q8 y- x
% W; ^: X. _) o( r(j) Turn the wheel and make sure that the wheel is installed correctly.
/ s2 I8 R, i# J& d) L' x/ _$ D, F7 T8 _+ L
(k) Install the casing (9).
+ Z+ Y- X, O7 Z, r3 v) v1 B" K# [+ N* Y5 G( k4 e: n, P# n) O8 [
(l) Install the bolts (5), the washers (2) and the new IPC-CSN (32-21-13-03-070) nuts (3) .
6 @+ }& ^1 ~2 C ^* D8 y$ m5 G' r% F+ j: A2 R* u
(m) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in) and safety them with the new IPC-CSN (32-21-13-03-060) cotter pins (4) . & ?( T7 z0 e* R
这是前轮安装工卡 请问红色的那句话怎么翻译 谢谢。 |
|