- 注册时间
- 2008-9-13
- 最后登录
- 1970-1-1
- 在线时间
- 0 小时
- 阅读权限
- 200
- 积分
- 0
- 帖子
- 24482
- 精华
- 4
- UID
- 9
 
|
|
TREES (FOREST)
Although a tree landing is not an attractive prospect,
the following general guidelines will help to make the
experience survivable.
• Use the normal landing configuration (full flaps,
gear down).
• Keep the groundspeed low by heading into the
wind.
• Make contact at minimum indicated airspeed, but
not below stall speed, and “hang” the airplane in
the tree branches in a nose-high landing attitude.
Involving the underside of the fuselage and both
wings in the initial tree contact provides a more
even and positive cushioning effect, while preventing
penetration of the windshield. [Figure
16-4]
• Avoid direct contact of the fuselage with heavy
tree trunks.
• Low, closely spaced trees with wide, dense
crowns (branches) close to the ground are much
better than tall trees with thin tops; the latter
allow too much free fall height. (A free fall from
75 feet results in an impact speed of about 40
knots, or about 4,000 f.p.m.)
• Ideally, initial tree contact should be symmetrical;
that is, both wings should meet equal
resistance in the tree branches. This distribution
of the load helps to maintain proper airplane
attitude. It may also preclude the loss of one
wing, which invariably leads to a more rapid and
less predictable descent to the ground.
• If heavy tree trunk contact is unavoidable once
the airplane is on the ground, it is best to involve
both wings simultaneously by directing the airplane
between two properly spaced trees. Do not
attempt this maneuver, however, while still
airborne.
WATER (DITCHING) AND SNOW
A well-executed water landing normally involves less
deceleration violence than a poor tree landing or a
Ch 16.qxd 5/7/04 10:30 AM Page 16-4
16-5
touchdown on extremely rough terrain. Also an
airplane that is ditched at minimum speed and in a normal
landing attitude will not immediately sink upon
touchdown. Intact wings and fuel tanks (especially
when empty) provide floatation for at least several
minutes even if the cockpit may be just below the
water line in a high-wing airplane.
Loss of depth perception may occur when landing on a
wide expanse of smooth water, with the risk of flying
into the water or stalling in from excessive altitude. To
avoid this hazard, the airplane should be “dragged in”
when possible. Use no more than intermediate flaps on
low-wing airplanes. The water resistance of fully
extended flaps may result in asymmetrical flap failure
and slowing of the airplane. Keep a retractable gear up
unless the AFM/POH advises otherwise.
A landing in snow should be executed like a ditching,
in the same configuration and with the same regard for
loss of depth perception (white out) in reduced visibility
and on wide open terrain.
ENGINE FAILURE AFTER TAKEOFF
(SINGLE-ENGINE)
The altitude available is, in many ways, the controlling
factor in the successful accomplishment of an emergency
landing. If an actual engine failure should occur
immediately after takeoff and before a safe maneuvering
altitude is attained, it is usually inadvisable to attempt
to turn back to the field from where the takeoff was
made. Instead, it is safer to immediately establish the
proper glide attitude, and select a field directly ahead
or slightly to either side of the takeoff path.
The decision to continue straight ahead is often
difficult to make unless the problems involved in
attempting to turn back are seriously considered. In the
first place, the takeoff was in all probability made into
the wind. To get back to the takeoff field, a downwind
turn must be made. This increases the groundspeed and
rushes the pilot even more in the performance of
procedures and in planning the landing approach.
Secondly, the airplane will be losing considerable
altitude during the turn and might still be in a bank
when the ground is contacted, resulting in the airplane
cartwheeling (which would be a catastrophe for the
occupants, as well as the airplane). After turning downwind,
the apparent increase in groundspeed could
mislead the pilot into attempting to prematurely slow
down the airplane and cause it to stall. On the other
hand, continuing straight ahead or making a slight turn
allows the pilot more time to establish a safe landing
attitude, and the landing can be made as slowly as
possible, but more importantly, the airplane can be
landed while under control.
Concerning the subject of turning back to the runway
following an engine failure on takeoff, the pilot should
determine the minimum altitude an attempt of such a
maneuver should be made in a particular airplane.
Experimentation at a safe altitude should give the pilot
an approximation of height lost in a descending 180°
turn at idle power. By adding a safety factor of about
25 percent, the pilot should arrive at a practical decision
height. The ability to make a 180° turn does not
necessarily mean that the departure runway can be
reached in a power-off glide; this depends on the wind,
the distance traveled during the climb, the height
reached, and the glide distance of the airplane without
power. The pilot should also remember that a turn back
to the departure runway may in fact require more than
a 180° change in direction.
Consider the following example of an airplane which
has taken off and climbed to an altitude of 300 feet
AGL when the engine fails. [Figure 16-5 on next
page]. After a typical 4 second reaction time, the pilot
elects to turn back to the runway. Using a standard rate
(3° change in direction per second) turn, it will take 1
minute to turn 180°. At a glide speed of 65 knots, the
radius of the turn is 2,100 feet, so at the completion of
the turn, the airplane will be 4,200 feet to one side of
the runway. The pilot must turn another 45° to head the
airplane toward the runway. By this time the total
change in direction is 225° equating to 75 seconds plus
the 4 second reaction time. If the airplane in a poweroff
glide descends at approximately 1,000 f.p.m., it
Figure 16-4.Tree landing.
Ch 16.qxd 5/7/04 10:30 AM Page 16-5
16-6
will have descended 1,316, feet placing it 1,016 feet
below the runway.
EMERGENCY DESCENTS
An emergency descent is a maneuver for descending
as rapidly as possible to a lower altitude or to the
ground for an emergency landing. [Figure 16-6] The
need for this maneuver may result from an uncontrollable
fire, a sudden loss of cabin pressurization, or any
other situation demanding an immediate and rapid
descent. The objective is to descend the airplane as
soon and as rapidly as possible, within the structural
limitations of the airplane. Simulated emergency
descents should be made in a turn to check for other air
traffic below and to look around for a possible
emergency landing area. A radio call announcing
descent intentions may be appropriate to alert other
aircraft in the area. When initiating the descent, a bank
of approximately 30 to 45° should be established to
maintain positive load factors (“G” forces) on the
airplane.
Emergency descent training should be performed as
recommended by the manufacturer, including the configuration
and airspeeds. Except when prohibited by
the manufacturer, the power should be reduced to idle,
and the propeller control (if equipped) should be
placed in the low pitch (or high revolutions per minute
(r.p.m.)) position. This will allow the propeller to act
as an aerodynamic brake to help prevent an excessive
airspeed buildup during the descent. The landing gear
and flaps should be extended as recommended by the
manufacturer. This will provide maximum drag so that
the descent can be made as rapidly as possible, without
excessive airspeed. The pilot should not allow the
airplane’s airspeed to pass the never-exceed speed
(VNE), the maximum landing gear extended speed
(VLE), or the maximum flap extended speed (VFE), as
applicable. In the case of an engine fire, a high
airspeed descent could blow out the fire. However, the
weakening of the airplane structure is a major concern
and descent at low airspeed would place less stress on
the airplane. If the descent is conducted in turbulent
conditions, the pilot must also comply with the design
maneuvering speed (VA) limitations. The descent
should be made at the maximum allowable airspeed
consistent with the procedure used. This will provide
increased drag and therefore the loss of altitude as
quickly as possible. The recovery from an emergency
descent should be initiated at a high enough altitude to
ensure a safe recovery back to level flight or a
precautionary landing.
When the descent is established and stabilized during
training and practice, the descent should be terminated.
Figure 16-5. Turning back to the runway after engine failure.
4,480 Ft.
180°
225°
300 Ft. AGL
1,016 Ft.
Ch 16.qxd 5/7/04 10:30 AM Page 16-6
16-7
In airplanes with piston engines, prolonged practice of
emergency descents should be avoided to prevent
excessive cooling of the engine cylinders.
IN-FLIGHT FIRE
Afire in flight demands immediate and decisive action.
The pilot therefore must be familiar with the procedures
outlined to meet this emergency contained in the
AFM/POH for the particular airplane. For the purposes
of this handbook, in-flight fires are classified as: inflight
engine fires, electrical fires, and cabin fires.
ENGINE FIRE
An in-flight engine compartment fire is usually caused
by a failure that allows a flammable substance such as
fuel, oil or hydraulic fluid to come in contact with a hot
surface. This may be caused by a mechanical failure of
the engine itself, an engine-driven accessory, a
defective induction or exhaust system, or a broken
line. Engine compartment fires may also result from
maintenance errors, such as improperly installed/fastened
lines and/or fittings resulting in leaks.
Engine compartment fires can be indicated by smoke
and/or flames coming from the engine cowling area.
They can also be indicated by discoloration, bubbling,
and/or melting of the engine cowling skin in cases
where flames and/or smoke is not visible to the pilot.
By the time a pilot becomes aware of an in-flight
engine compartment fire, it usually is well developed.
Unless the airplane manufacturer directs otherwise in
the AFM/POH, the first step on discovering a fire
should be to shut off the fuel supply to the engine by
placing the mixture control in the idle cut off position
and the fuel selector shutoff valve to the OFF position.
The ignition switch should be left ON in order to use
up the fuel that remains in the fuel lines and components
between the fuel selector/shutoff valve and
the engine. This procedure may starve the engine
compartment of fuel and cause the fire to die naturally.
If the flames are snuffed out, no attempt should be
made to restart the engine.
If the engine compartment fire is oil-fed, as evidenced
by thick black smoke, as opposed to a fuel-fed fire
which produces bright orange flames, the pilot should
consider stopping the propeller rotation by feathering
or other means, such as (with constant-speed propellers)
placing the pitch control lever to the minimum
r.p.m. position and raising the nose to reduce airspeed
until the propeller stops rotating. This procedure will
stop an engine-driven oil (or hydraulic) pump from
continuing to pump the flammable fluid which is
feeding the fire.
Some light airplane emergency checklists direct the
pilot to shut off the electrical master switch. However,
the pilot should consider that unless the fire is electrical
in nature, or a crash landing is imminent, deactivating
the electrical system prevents the use of panel radios
for transmitting distress messages and will also cause
air traffic control (ATC) to lose transponder returns.
Pilots of powerless single-engine airplanes are left
with no choice but to make a forced landing. Pilots of
twin-engine airplanes may elect to continue the flight
to the nearest airport. However, consideration must be
given to the possibility that a wing could be seriously
impaired and lead to structural failure. Even a brief but
intense fire could cause dangerous structural damage.
In some cases, the fire could continue to burn under
the wing (or engine cowling in the case of a singleengine
airplane) out of view of the pilot. Engine
compartment fires which appear to have been
extinguished have been known to rekindle with
changes in airflow pattern and airspeed.
The pilot must be familiar with the airplane’s emergency
descent procedures. The pilot must bear in mind
that:
• The airplane may be severely structurally damaged
to the point that its ability to remain under
control could be lost at any moment.
• The airplane may still be on fire and susceptible
to explosion.
• The airplane is expendable and the only thing that
matters is the safety of those on board.
ELECTRICAL FIRES
The initial indication of an electrical fire is usually the
distinct odor of burning insulation. Once an electrical
fire is detected, the pilot should attempt to identify the
faulty circuit by checking circuit breakers, instruments,
avionics, and lights. If the faulty circuit cannot be readily
detected and isolated, and flight conditions permit,
the battery master switch and alternator/generator
switches should be turned off to remove the possible
source of the fire. However, any materials which have
been ignited may continue to burn.
Figure 16-6. Emergency descent.
Ch 16.qxd 5/7/04 10:30 AM Page 16-7
16-8
If electrical power is absolutely essential for the flight,
an attempt may be made to identify and isolate the
faulty circuit by:
1. Turning the electrical master switch OFF.
2. Turning all individual electrical switches OFF.
3. Turning the master switch back ON.
4. Selecting electrical switches that were ON before
the fire indication one at a time, permitting a short
time lapse after each switch is turned on to check
for signs of odor, smoke, or sparks.
This procedure, however, has the effect of recreating
the original problem. The most prudent course of
action is to land as soon as possible.
CABIN FIRE
Cabin fires generally result from one of three sources:
(1) careless smoking on the part of the pilot and/or
passengers; (2) electrical system malfunctions; (3)
heating system malfunctions. A fire in the cabin presents
the pilot with two immediate demands: attacking
the fire, and getting the airplane safely on the ground
as quickly as possible. A fire or smoke in the cabin
should be controlled by identifying and shutting down
the faulty system. In many cases, smoke may be
removed from the cabin by opening the cabin air vents.
This should be done only after the fire extinguisher (if
available) is used. Then the cabin air control can be
opened to purge the cabin of both smoke and fumes. If
smoke increases in intensity when the cabin air vents
are opened, they should be immediately closed. This
indicates a possible fire in the heating system, nose
compartment baggage area (if so equipped), or that the
increase in airflow is feeding the fire.
On pressurized airplanes, the pressurization air system
will remove smoke from the cabin; however, if the
smoke is intense, it may be necessary to either depressurize
at altitude, if oxygen is available for all
occupants, or execute an emergency descent.
In unpressurized single-engine and light twin-engine
airplanes, the pilot can attempt to expel the smoke
from the cabin by opening the foul weather windows.
These windows should be closed immediately if the
fire becomes more intense. If the smoke is severe, the
passengers and crew should use oxygen masks if available,
and the pilot should initiate an immediate
descent. The pilot should also be aware that on some
airplanes, lowering the landing gear and/or wing flaps
can aggravate a cabin smoke problem.
FLIGHT CONTROL
MALFUNCTION/FAILURE
TOTAL FLAP FAILURE
The inability to extend the wing flaps will necessitate
a no-flap approach and landing. In light airplanes a noflap
approach and landing is not particularly difficult
or dangerous. However, there are certain factors which
must be considered in the execution of this maneuver.
A no-flap landing requires substantially more runway
than normal. The increase in required landing distance
could be as much as 50 percent.
When flying in the traffic pattern with the wing flaps
retracted, the airplane must be flown in a relatively
nose-high attitude to maintain altitude, as compared to
flight with flaps extended. Losing altitude can be more
of a problem without the benefit of the drag normally
provided by flaps. A wider, longer traffic pattern may
be required in order to avoid the necessity of diving to
lose altitude and consequently building up excessive
airspeed.
On final approach, a nose-high attitude can make it
difficult to see the runway. This situation, if not anticipated,
can result in serious errors in judgment of
height and distance. Approaching the runway in a
relatively nose-high attitude can also cause the
perception that the airplane is close to a stall. This may
cause the pilot to lower the nose abruptly and risk
touching down on the nosewheel.
With the flaps retracted and the power reduced for
landing, the airplane is slightly less stable in the pitch
and roll axes. Without flaps, the airplane will tend to
float considerably during roundout. The pilot should
avoid the temptation to force the airplane onto the runway
at an excessively high speed. Neither should the
pilot flare excessively, because without flaps this
might cause the tail to strike the runway.
ASYMMETRIC (SPLIT) FLAP
An asymmetric “split” flap situation is one in which
one flap deploys or retracts while the other remains in
position. The problem is indicated by a pronounced
roll toward the wing with the least flap deflection
when wing flaps are extended/retracted.
The roll encountered in a split flap situation is countered
with opposite aileron. The yaw caused by the
additional drag created by the extended flap will
require substantial opposite rudder, resulting in a
cross-control condition. Almost full aileron may be
required to maintain a wings-level attitude, especially
at the reduced airspeed necessary for approach and
landing. The pilot therefore should not attempt to land
Ch 16.qxd 5/7/04 10:30 AM Page 16-8
16-9
with a crosswind from the side of the deployed flap,
because the additional roll control required to counteract
the crosswind may not be available.
The pilot must be aware of the difference in stall
speeds between one wing and the other in a split flap
situation. The wing with the retracted flap will stall
considerably earlier than the wing with the deployed
flap. This type of asymmetrical stall will result in an
uncontrollable roll in the direction of the stalled (clean)
wing. If altitude permits, a spin will result.
The approach to landing with a split flap condition
should be flown at a higher than normal airspeed. The
pilot should not risk an asymmetric stall and subsequent
loss of control by flaring excessively. Rather, the
airplane should be flown onto the runway so that the
touchdown occurs at an airspeed consistent with a safe
margin above flaps-up stall speed.
LOSS OF ELEVATOR CONTROL
In many airplanes, the elevator is controlled by two
cables: a “down” cable and an “up” cable. Normally,
a break or disconnect in only one of these cables will
not result in a total loss of elevator control. In most
airplanes, a failed cable results in a partial loss of
pitch control. In the failure of the “up” elevator cable
(the “down” elevator being intact and functional) the
control yoke will move aft easily but produce no
response. Forward yoke movement, however, beyond
the neutral position produces a nosedown attitude.
Conversely, a failure of the “down” elevator cable,
forward movement of the control yoke produces no
effect. The pilot will, however, have partial control of
pitch attitude with aft movement.
When experiencing a loss of up-elevator control, the
pilot can retain pitch control by:
• Applying considerable nose-up trim.
• Pushing the control yoke forward to attain and
maintain desired attitude.
• Increasing forward pressure to lower the nose and
relaxing forward pressure to raise the nose.
• Releasing forward pressure to flare for landing.
When experiencing a loss of down-elevator control,
the pilot can retain pitch control by:
• Applying considerable nosedown trim.
• Pulling the control yoke aft to attain and maintain
attitude.
• Releasing back pressure to lower the nose and
increasing back pressure to raise the nose.
• Increasing back pressure to flare for landing.
Trim mechanisms can be useful in the event of an
in-flight primary control failure. For example, if the
linkage between the cockpit and the elevator fails in
flight, leaving the elevator free to weathervane in the
wind, the trim tab can be used to raise or lower the
elevator, within limits. The trim tabs are not as effective
as normal linkage control in conditions such as
low airspeed, but they do have some positive effect—
usually enough to bring about a safe landing.
If an elevator becomes jammed, resulting in a total loss
of elevator control movement, various combinations of
power and flap extension offer a limited amount of
pitch control. A successful landing under these conditions,
however, is problematical.
LANDING GEAR MALFUNCTION
Once the pilot has confirmed that the landing gear has
in fact malfunctioned, and that one or more gear legs
refuses to respond to the conventional or alternate
methods of gear extension contained in the AFM/POH,
there are several methods that may be useful in
attempting to force the gear down. One method is to
dive the airplane (in smooth air only) to VNE speed (red
line on the airspeed indicator) and (within the limits of
safety) execute a rapid pull up. In normal category
airplanes, this procedure will create a 3.8 G load on the
structure, in effect making the landing gear weigh 3.8
times normal. In some cases, this may force the landing
gear into the down and locked position. This
procedure requires a fine control touch and good feel
for the airplane. The pilot must avoid exceeding the
design stress limits of the airplane while attempting to
lower the landing gear. The pilot must also avoid an
accelerated stall and possible loss of control while
attention is directed to solving the landing gear
problem.
Another method that has proven useful in some cases
is to induce rapid yawing. After stabilizing at or
slightly less than maneuvering speed (VA), the pilot
should alternately and aggressively apply rudder in one
direction and then the other in rapid sequence. The
resulting yawing action may cause the landing gear to
fall into place.
If all efforts to extend the landing gear have failed, and
a gear up landing is inevitable, the pilot should select
an airport with crash and rescue facilities. The pilot
should not hesitate to request that emergency equipment
be standing by.
When selecting a landing surface, the pilot should consider
that a smooth, hard-surface runway usually
causes less damage than rough, unimproved grass
strips. A hard surface does, however, create sparks that
can ignite fuel. If the airport is so equipped, the pilot
Ch 16.qxd 5/7/04 10:30 AM Page 16-9
16-10
can request that the runway surface be foamed. The
pilot should consider burning off excess fuel. This will
reduce landing speed and fire potential.
If the landing gear malfunction is limited to one main
landing gear leg, the pilot should consume as much
fuel from that side of the airplane as practicable,
thereby reducing the weight of the wing on that side.
The reduced weight makes it possible to delay the
unsupported wing from contacting the surface during
the landing roll until the last possible moment.
Reduced impact speeds result in less damage.
If only one landing gear leg fails to extend, the pilot
has the option of landing on the available gear legs, or
landing with all the gear legs retracted. Landing on
only one main gear usually causes the airplane to veer
strongly in the direction of the faulty gear leg after
touchdown. If the landing runway is narrow, and/or
ditches and obstacles line the runway edge, maximum
directional control after touchdown is a necessity. In
this situation, a landing with all three gear retracted
may be the safest course of action.
If the pilot elects to land with one main gear retracted
(and the other main gear and nose gear down and
locked), the landing should be made in a nose-high
attitude with the wings level. As airspeed decays, the
pilot should apply whatever aileron control is necessary
to keep the unsupported wing airborne as long as
possible. [Figure 16-7] Once the wing contacts the
surface, the pilot can anticipate a strong yaw in that
direction. The pilot must be prepared to use full
opposite rudder and aggressive braking to maintain
some degree of directional control.
When landing with a retracted nosewheel (and the
main gear extended and locked) the pilot should hold
the nose off the ground until almost full up-elevator
has been applied. [Figure 16-8] The pilot should then
release back pressure in such a manner that the nose
settles slowly to the surface. Applying and holding full
up-elevator will result in the nose abruptly dropping to
the surface as airspeed decays, possibly resulting in
burrowing and/or additional damage. Brake pressure
should not be applied during the landing roll unless
absolutely necessary to avoid a collision with obstacles.
If the landing must be made with only the nose gear
extended, the initial contact should be made on the aft
fuselage structure with a nose-high attitude. This
procedure will help prevent porpoising and/or wheelbarrowing.
The pilot should then allow the nosewheel
to gradually touch down, using nosewheel steering as
necessary for directional control.
SYSTEMS MALFUNCTIONS
ELECTRICAL SYSTEM
The loss of electrical power can deprive the pilot of
numerous critical systems, and therefore should not
be taken lightly even in day/VFR conditions. Most
in-flight failures of the electrical system are located
in the generator or alternator. Once the generator or
alternator system goes off line, the electrical source
in a typical light airplane is a battery. If a warning
light or ammeter indicates the probability of an alternator
or generator failure in an airplane with only one
generating system, however, the pilot may have very
little time available from the battery.
The rating of the airplane battery provides a clue to how
long it may last. With batteries, the higher the amperage
load, the less the usable total amperage. Thus a 25-amp
hour battery could produce 5 amps per hour for 5 hours,
but if the load were increased to 10 amps, it might last
only 2 hours. A 40-amp load might discharge the battery
fully in about 10 or 15 minutes. Much depends on the
battery condition at the time of the system failure. If the
battery has been in service for a few years, its power may
be reduced substantially because of internal resistance.
Or if the system failure was not detected immediately,
much of the stored energy may have already been used. It
is essential, therefore, that the pilot immediately shed
non-essential loads when the generating source fails.
[Figure 16-9] The pilot should then plan to land at the
nearest suitable airport.
What constitutes an “emergency” load following a
generating system failure cannot be predetermined,
because the actual circumstances will always be
somewhat different—for example, whether the flight
is VFR or IFR, conducted in day or at night, in clouds
or in the clear. Distance to nearest suitable airport can
also be a factor.
Figure 16-7. Landing with one main gear retracted.
Figure 16-8. Landing with nosewheel retracted.
Ch 16.qxd 5/7/04 10:30 AM Page 16-10
16-11
The pilot should remember that the electrically powered
(or electrically selected) landing gear and flaps will not
function properly on the power left in a partially
depleted battery. Landing gear and flap motors use up
power at rates much greater than most other types of
electrical equipment. The result of selecting these
motors on a partially depleted battery may well result in
an immediate total loss of electrical power.
If the pilot should experience a complete in-flight loss
of electrical power, the following steps should be
taken:
• Shed all but the most necessary electricallydriven
equipment.
• Understand that any loss of electrical power is
critical in a small airplane—notify ATC of the situation
immediately. Request radar vectors for a
landing at the nearest suitable airport.
• If landing gear or flaps are electrically controlled
or operated, plan the arrival well ahead of time.
Expect to make a no-flap landing, and anticipate
a manual landing gear extension.
PITOT-STATIC SYSTEM
The source of the pressure for operating the airspeed
indicator, the vertical speed indicator, and the altimeter
is the pitot-static system. The major components of the
pitot-static system are the impact pressure chamber
and lines, and the static pressure chamber and lines,
each of which are subject to total or partial blockage
by ice, dirt, and/or other foreign matter. Blockage of
the pitot-static system will adversely affect instrument
operation. [Figure 16-10 on next page]
Partial static system blockage is insidious in that it
may go unrecognized until a critical phase of flight.
During takeoff, climb, and level-off at cruise altitude
the altimeter, airspeed indicator, and vertical speed
indicator may operate normally. No indication of
malfunction may be present until the airplane begins
a descent.
If the static reference system is severely restricted, but
not entirely blocked, as the airplane descends, the
static reference pressure at the instruments begins to
lag behind the actual outside air pressure. While
descending, the altimeter may indicate that the airplane
is higher than actual because the obstruction slows the
airflow from the static port to the altimeter. The
vertical speed indicator confirms the altimeter’s information
regarding rate of change, because the reference
pressure is not changing at the same rate as the outside
air pressure. The airspeed indicator, unable to tell
whether it is experiencing more airspeed pitot pressure
or less static reference pressure, indicates a higher
airspeed than actual. To the pilot, the instruments
indicate that the airplane is too high, too fast, and
descending at a rate much less than desired.
If the pilot levels off and then begins a climb, the
altitude indication may still lag. The vertical speed
indicator will indicate that the airplane is not climbing
as fast as actual. The indicated airspeed, however, may
begin to decrease at an alarming rate. The least amount
of pitch-up attitude may cause the airspeed needle to
indicate dangerously near stall speed.
Managing a static system malfunction requires that the
pilot know and understand the airplane’s pitot-static
system. If a system malfunction is suspected, the pilot
should confirm it by opening the alternate static
source. This should be done while the airplane is
climbing or descending. If the instrument needles
move significantly when this is done, a static pressure
problem exists and the alternate source should be used
during the remainder of the flight.
ABNORMAL ENGINE INSTRUMENT
INDICATIONS
The AFM/POH for the specific airplane contains information
that should be followed in the event of any
A. Continuous Load
Pitot Heating (Operating)
Wingtip Lights
Heater Igniter
**Navigation Receivers
**Communications Receivers
Fuel Indicator
Instrument Lights (overhead)
Engine Indicator
Compass Light
Landing Gear Indicator
Flap Indicator
B. Intermittent Load
Starter
Landing Lights
Heater Blower Motor
Flap Motor
Landing Gear Motor
Cigarette Lighter
Transceiver (keyed)
Fuel Boost Pump
Cowl Flap Motor
Stall Warning Horn
** Amperage for radios varies with equipment. In general,
the more recent the model, the less amperage required.
NOTE: Panel and indicator lights usually draw less than
one amp.
1
4
1
1-4
1-2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
3.30
3.00
1-20
1-2 each
1-2 each
0.40
0.60
0.30
0.20
0.17
0.17
100.00
17.80
14.00
13.00
10.00
7.50
5-7
2.00
1.00
1.50
Electrical Loads for
Light Single
Number
of Units
Total
Amperes
Figure 16-9. Electrical load for light single.
Ch 16.qxd 5/7/04 10:30 AM Page 16-11
16-12
abnormal engine instrument indications. The table on
the next page offers generic information on some of
the more commonly experienced in-flight abnormal
engine instrument indications, their possible causes,
and corrective actions. [Table 1]
DOOR OPENING IN FLIGHT
In most instances, the occurrence of an inadvertent
door opening is not of great concern to the safety of a
flight, but rather, the pilot’s reaction at the moment the
incident happens. A door opening in flight may be
accompanied by a sudden loud noise, sustained noise
level and possible vibration or buffeting. If a pilot
allows himself or herself to become distracted to the
point where attention is focused on the open door
rather than maintaining control of the airplane, loss of
control may result, even though disruption of airflow
by the door is minimal.
In the event of an inadvertent door opening in flight or
on takeoff, the pilot should adhere to the following.
• Concentrate on flying the airplane. Particularly in
light single- and twin-engine airplanes; a cabin
door that opens in flight seldom if ever compromises
the airplane’s ability to fly. There may be
some handling effects such as roll and/or yaw, but
in most instances these can be easily overcome.
• If the door opens after lift-off, do not rush to land.
Climb to normal traffic pattern altitude, fly a normal
traffic pattern, and make a normal landing.
• Do not release the seat belt and shoulder harness
in an attempt to reach the door. Leave the door
alone. Land as soon as practicable, and close the
door once safely on the ground.
• Remember that most doors will not stay wide
open. They will usually bang open, then settle
partly closed. A slip towards the door may cause
it to open wider; a slip away from the door may
push it closed.
• Do not panic. Try to ignore the unfamiliar noise
and vibration. Also, do not rush. Attempting to
get the airplane on the ground as quickly as possible
may result in steep turns at low altitude.
• Complete all items on the landing checklist.
• Remember that accidents are almost never
caused by an open door. Rather, an open door
accident is caused by the pilot’s distraction or
failure to maintain control of the airplane.
INADVERTENT VFR FLIGHT INTO IMC
GENERAL
It is beyond the scope of this handbook to incorporate
a course of training in basic attitude instrument
flying. This information is contained in FAA-H-
8083-15, Instrument Flying Handbook. Certain
pilot certificates and/or associated ratings require
training in instrument flying and a demonstration of
specific instrument flying tasks on the practical test.
Effect of Blocked
Pitot/Static
Sources on Airspeed,
Altimeter and
Vertical Speed Indications
Pitot Source Blocked
One Static
Source Blocked
Both Static
Sources Blocked
Both Static and
Pitot Sources Blocked
Increases with altitude
gain; decreases
with altitude loss.
Decreases with altitude
gain; increases
with altitude loss.
Unaffected Unaffected
Does not change
with actual gain or
loss of altitude.
Does not change
with actual variations
in vertical speed.
Inaccurate while sideslipping; very sensitive in turbulence.
All indications remain constant, regardless of actual changes
in airspeed, altitude and vertical speed.
Indicated Airspeed Indicated Altitude
Indicated
Vertical Speed
Figure 16-10. Effects of blocked pitot-static sources.
Ch 16.qxd 5/7/04 10:30 AM Page 16-12
16-13
Pilots and flight instructors should refer to FAA-H-
8083-15 for guidance in the performance of these
tasks, and to the appropriate practical test standards
for information on the standards to which these
required tasks must be performed for the particular
certificate level and/or rating. The pilot should
remember, however, that unless these tasks are practiced
on a continuing and regular basis, skill erosion
begins almost immediately. In a very short time, the
pilot’s assumed level of confidence will be much
higher than the performance he or she will actually
be able to demonstrate should the need arise.
Accident statistics show that the pilot who has not
been trained in attitude instrument flying, or one
whose instrument skills have eroded, will lose control
of the airplane in about 10 minutes once forced
to rely solely on instrument reference. The purpose
of this section is to provide guidance on practical
emergency measures to maintain airplane control for
a limited period of time in the event a VFR pilot
encounters IMC conditions. The main goal is not
precision instrument flying; rather, it is to help the
VFR pilot keep the airplane under adequate control
until suitable visual references are regained.
MALFUNCTION PROBABLE CAUSE CORRECTIVE ACTION
Loss of r.p.m. during cruise flight
(non-altitude engines)
Carburetor or induction icing or air filter
clogging
Apply carburetor heat. If dirty filter is
suspected and non-filtered air is available,
switch selector to unfiltered position.
Loss of manifold pressure during cruise
flight
Same as above Same as above.
Turbocharger failure Possible exhaust leak. Shut down engine
or use lowest practicable power setting.
Land as soon as possible.
Gain of manifold pressure during cruise
flight
Throttle has opened, propeller control has
decreased r.p.m., or improper method of
power reduction
Readjust throttle and tighten friction lock.
Reduce manifold pressure prior to
reducing r.p.m.
High oil temperature Oil congealed in cooler Reduce power. Land. Preheat engine.
Inadequate engine cooling Reduce power. Increase airspeed.
Detonation or preignition Observe cylinder head temperatures for
high reading. Reduce manifold pressure.
Enrich mixture.
Forth coming internal engine faiure Land as soon as possible or feather
propeller and stop engine.
Land as soon as possible or feather
propeller and stop engine.
Defective thermostatic oil cooler control Land as soon as possible. Consult
maintenance personnel.
Low oil temperature Engine not warmed up to operating
temperature
Warm engine in prescribed manner.
High oil pressure Cold oil Same as above.
Same as above.
Same as above.
Same as above.
Same as above.
Same as above.
Possible internal plugging Reduce power. Land as soon as possible.
Low oil pressure Broken pressure relief valve
Insufficient oil
Burned out bearings
Fluctuating oil pressure Low oil supply, loose oil lines, defective
pressure relief valve
Improper cowl flap adjustment Adjust cowl flaps.
Adjust cowl flaps.
Insufficient airspeed for cooling Increase airspeed.
Improper mixture adjustment Adjust mixture.
Detonation or preignition Reduce power, enrich mixture, increase
cooling airflow.
Low cylinder head temperature
High cylinder head temperature
Excessive cowl flap opening
Excessively rich mixture Adjust mixture control.
Exteneded glides without clearing engine Clear engine long enough to keep
temperatures at minimum range.
Ammeter indicating discharge Alternator or generator failure Shed unnecessary electrical load. Land
as soon as practicable.
Load meter indicating zero Same as above
Surging r.p.m. and overspeeding Defective propeller
Defective propeller governor
Adjust propeller r.p.m.
Defective engine Consult maintenance.
Consult maintenance personnel.
Consult maintenance.
Adjust propeller control. Attempt to
restore normal operation.
Defective tachometer
Improper mixture setting Readjust mixture for smooth operation.
Adjust mixture for smooth operation.
Loss of airspeed in cruise flight with
manifold pressure and r.p.m. constant
Possible loss of one or more cylinders Land as soon as possible.
Rough running engine Improper mixture control setting
Defective ignition or valves
Detonation or preignition Reduce power, enrich mixture, open cowl
flaps to reduce cylinder head temp. Land
as soon as practicable.
Induction air leak Reduce power. Consult maintenance.
Plugged fuel nozzle (Fuel injection)
Excessive fuel pressure or fuel flow Lean mixture control.
Loss of fuel pressure Engine driven pump failure Turn on boost tanks.
No fuel Switch tanks, turn on fuel.
Table 1.
Ch 16.qxd 5/7/04 10:30 AM Page 16-13
16-14
The first steps necessary for surviving an encounter
with instrument meteorological conditions (IMC) by a
VFR pilot are:
• Recognition and acceptance of the seriousness of
the situation and the need for immediate remedial
action.
• Maintaining control of the airplane.
• Obtaining the appropriate assistance in getting the
airplane safely on the ground.
RECOGNITION
A VFR pilot is in IMC conditions anytime he or she is
unable to maintain airplane attitude control by reference
to the natural horizon, regardless of the circumstances
or the prevailing weather conditions. Additionally, the
VFR pilot is, in effect, in IMC anytime he or she is inadvertently,
or intentionally for an indeterminate period of
time, unable to navigate or establish geographical
position by visual reference to landmarks on the
surface. These situations must be accepted by the pilot
involved as a genuine emergency, requiring appropriate
action.
The pilot must understand that unless he or she is
trained, qualified, and current in the control of an airplane
solely by reference to flight instruments, he or she
will be unable to do so for any length of time. Many
hours of VFR flying using the attitude indicator as a
reference for airplane control may lull a pilot into a false
sense of security based on an overestimation of his or
her personal ability to control the airplane solely by
instrument reference. In VFR conditions, even though
the pilot thinks he or she is controlling the airplane by
instrument reference, the pilot also receives an overview
of the natural horizon and may subconsciously rely on it
more than the cockpit attitude indicator. If the natural
horizon were to suddenly disappear, the untrained
instrument pilot would be subject to vertigo, spatial
disorientation, and inevitable control loss.
MAINTAINING AIRPLANE CONTROL
Once the pilot recognizes and accepts the situation, he
or she must understand that the only way to control the
airplane safely is by using and trusting the flight instruments.
Attempts to control the airplane partially by
reference to flight instruments while searching outside
the cockpit for visual confirmation of the information
provided by those instruments will result in inadequate
airplane control. This may be followed by spatial
disorientation and complete control loss.
The most important point to be stressed is that the pilot
must not panic. The task at hand may seem overwhelming,
and the situation may be compounded by
extreme apprehension. The pilot therefore must make
a conscious effort to relax.
The pilot must understand the most important concern—
in fact the only concern at this point—is to keep
the wings level. An uncontrolled turn or bank usually
leads to difficulty in achieving the objectives of any
desired flight condition. The pilot will find that good
bank control has the effect of making pitch control
much easier.
The pilot should remember that a person cannot feel
control pressures with a tight grip on the controls.
Relaxing and learning to “control with the eyes and
the brain” instead of only the muscles, usually takes
considerable conscious effort.
The pilot must believe what the flight instruments
show about the airplane’s attitude regardless of what
the natural senses tell. The vestibular sense (motion
sensing by the inner ear) can and will confuse the pilot.
Because of inertia, the sensory areas of the inner ear
cannot detect slight changes in airplane attitude, nor
can they accurately sense attitude changes which occur
at a uniform rate over a period of time. On the other
hand, false sensations are often generated, leading the
pilot to believe the attitude of the airplane has changed
when, in fact, it has not. These false sensations result
in the pilot experiencing spatial disorientation.
ATTITUDE CONTROL
An airplane is, by design, an inherently stable platform
and, except in turbulent air, will maintain approximately
straight-and-level flight if properly trimmed
and left alone. It is designed to maintain a state of
equilibrium in pitch, roll, and yaw. The pilot must be
aware, however, that a change about one axis will
affect the stability of the others. The typical light
airplane exhibits a good deal of stability in the yaw
axis, slightly less in the pitch axis, and even lesser still
in the roll axis. The key to emergency airplane attitude
control, therefore, is to:
• Trim the airplane with the elevator trim so that it
will maintain hands-off level flight at cruise airspeed.
• Resist the tendency to over control the airplane.
Fly the attitude indicator with fingertip control.
No attitude changes should be made unless the
flight instruments indicate a definite need for a
change.
• Make all attitude changes smooth and small, yet
with positive pressure. Remember that a small
change as indicated on the horizon bar corresponds
to a proportionately much larger change
in actual airplane attitude.
• Make use of any available aid in attitude control
such as autopilot or wing leveler.
Ch 16.qxd 5/7/04 10:30 AM Page 16-14
16-15
The primary instrument for attitude control is the attitude
indicator. [Figure 16-11] Once the airplane is
trimmed so that it will maintain hands-off level flight
at cruise airspeed, that airspeed need not vary until the
airplane must be slowed for landing. All turns, climbs
and descents can and should be made at this airspeed.
Straight flight is maintained by keeping the wings level
using “fingertip pressure” on the control wheel. Any
pitch attitude change should be made by using no more
than one bar width up or down.
TURNS
Turns are perhaps the most potentially dangerous
maneuver for the untrained instrument pilot for two
reasons.
• The normal tendency of the pilot to over control,
leading to steep banks and the possibility of a
“graveyard spiral.”
• The inability of the pilot to cope with the instability
resulting from the turn.
When a turn must be made, the pilot must anticipate
and cope with the relative instability of the roll axis.
The smallest practical bank angle should be used—in
any case no more than 10° bank angle. [Figure 16-12]
A shallow bank will take very little vertical lift from
the wings resulting in little if any deviation in altitude.
It may be helpful to turn a few degrees and then return
to level flight, if a large change in heading must be
made. Repeat the process until the desired heading is
reached. This process may relieve the progressive
overbanking that often results from prolonged turns.
CLIMBS
If a climb is necessary, the pilot should raise the
miniature airplane on the attitude indicator no more
than one bar width and apply power. [Figure 16-13]
The pilot should not attempt to attain a specific climb
speed but accept whatever speed results. The objective
is to deviate as little as possible from level flight
attitude in order to disturb the airplane’s equilibrium
as little as possible. If the airplane is properly
trimmed, it will assume a nose-up attitude on its own
commensurate with the amount of power applied.
Torque and P-factor will cause the airplane to have a
Figure 16-11. Attitude indicator.
Figure 16-12. Level turn.
Figure 16-13. Level climb.
Ch 16.qxd 5/7/04 10:30 AM Page 16-15
16-16
tendency to bank and turn to the left. This must be
anticipated and compensated for. If the initial power
application results in an inadequate rate of climb,
power should be increased in increments of 100 r.p.m.
or 1 inch of manifold pressure until the desired rate of
climb is attained. Maximum available power is
seldom necessary. The more power used the more the
airplane will want to bank and turn to the left.
Resuming level flight is accomplished by first
decreasing pitch attitude to level on the attitude
indicator using slow but deliberate pressure, allowing
airspeed to increase to near cruise value, and then
decreasing power.
DESCENTS
Descents are very much the opposite of the climb
procedure if the airplane is properly trimmed for
hands-off straight-and-level flight. In this configuration,
the airplane requires a certain amount of thrust to
maintain altitude. The pitch attitude is controlling the
airspeed. The engine power, therefore, (translated into
thrust by the propeller) is maintaining the selected
altitude. Following a power reduction, however slight,
there will be an almost imperceptible decrease in
airspeed. However, even a slight change in speed
results in less down load on the tail, whereupon the
designed nose heaviness of the airplane causes it to
pitch down just enough to maintain the airspeed for
which it was trimmed. The airplane will then descend
at a rate directly proportionate to the amount of thrust
that has been removed. Power reductions should be
made in increments of 100 r.p.m. or 1 inch of manifold
pressure and the resulting rate of descent should never
exceed 500 f.p.m. The wings should be held level on
the attitude indicator, and the pitch attitude should not
exceed one bar width below level. [Figure 16-14]
COMBINED MANEUVERS
Combined maneuvers, such as climbing or descending
turns should be avoided if at all possible by an
untrained instrument pilot already under the stress of
an emergency situation. Combining maneuvers will
only compound the problems encountered in individual
maneuvers and increase the risk of control loss.
Remember that the objective is to maintain airplane
control by deviating as little as possible from straightand-
level flight attitude and thereby maintaining as
much of the airplane’s natural equilibrium as possible.
When being assisted by air traffic controllers from the
ground, the pilot may detect a sense of urgency as he
or she is being directed to change heading and/or altitude.
This sense of urgency reflects a normal concern
for safety on the part of the controller. But the pilot
must not let this prompt him or her to attempt a maneuver
that could result in loss of control.
TRANSITION TO VISUAL FLIGHT
One of the most difficult tasks a trained and qualified
instrument pilot must contend with is the transition
from instrument to visual flight prior to landing. For
the untrained instrument pilot, these difficulties are
magnified.
The difficulties center around acclimatization and
orientation. On an instrument approach the trained
instrument pilot must prepare in advance for the
transition to visual flight. The pilot must have a
mental picture of what he or she expects to see once
the transition to visual flight is made and quickly
acclimatize to the new environment. Geographical
orientation must also begin before the transition as the
pilot must visualize where the airplane will be in relation
to the airport/runway when the transition occurs
so that the approach and landing may be completed by
visual reference to the ground.
In an ideal situation the transition to visual flight is
made with ample time, at a sufficient altitude above
terrain, and to visibility conditions sufficient to
accommodate acclimatization and geographical
orientation. This, however, is not always the case. The
untrained instrument pilot may find the visibility still
limited, the terrain completely unfamiliar, and altitude
above terrain such that a “normal” airport traffic
pattern and landing approach is not possible.
Additionally, the pilot will most likely be under
considerable self-induced psychological pressure to
Figure 16-14. Level descent.
Ch 16.qxd 5/7/04 10:30 AM Page 16-16
16-17
get the airplane on the ground. The pilot must take this
into account and, if possible, allow time to become
acclimatized and geographically oriented before
attempting an approach and landing, even if it means
flying straight and level for a time or circling the
airport. This is especially true at night.
Ch 16.qxd 5/7/04 10:30 AM Page 16-17
16-18
Ch 16.qxd 5/7/04 10:30 AM Page 16-18
100-HOUR INSPECTION—
An inspection, identical in scope to an
annual inspection. Must be conducted
every 100 hours of flight on aircraft of
under 12,500 pounds that are used
for hire.
ABSOLUTE ALTITUDE—
The vertical distance of an airplane
above the terrain, or above ground
level (AGL).
ABSOLUTE CEILING—
The altitude at which a climb is no
longer possible.
ACCELERATE-GO DISTANCE—
The distance required to accelerate to
V1 with all engines at takeoff power,
experience an engine failure at V1 and
continue the takeoff on the remaining
engine(s). The runway required
includes the distance required to
climb to 35 feet by which time V2
speed must be attained.
ACCELERATE-STOP
DISTANCE—The distance required
to accelerate to V1 with all engines at
takeoff power, experience an engine
failure at V1, and abort the takeoff and
bring the airplane to a stop using braking
action only (use of thrust reversing
is not considered).
ACCELERATION—Force involved
in overcoming inertia, and which may
be defined as a change in velocity per
unit of time.
ACCESSORIES—Components that
are used with an engine, but are not a
part of the engine itself. Units such as
magnetos, carburetors, generators,
and fuel pumps are commonly
installed engine accessories.
ADJUSTABLE STABILIZER—
A stabilizer that can be adjusted in
flight to trim the airplane, thereby
even a trim tab, which provides
aerodynamic force when it interacts
with a moving stream of air.
AIRMANSHIP SKILLS—The skills
of coordination, timing, control touch,
and speed sense in addition to the
motor skills required to fly an aircraft.
AIRMANSHIP—
A sound acquaintance with the
principles of flight, the ability to
operate an airplane with competence
and precision both on the ground and
in the air, and the exercise of sound
judgment that results in optimal
operational safety and efficiency.
AIRPLANE FLIGHT MANUAL
(AFM)—A document developed by
the airplane manufacturer and
approved by the Federal Aviation
Administration (FAA). It is specific to
a particular make and model airplane
by serial number and it contains
operating procedures and limitations.
AIRPLANE OWNER/
INFORMATION MANUAL—A
document developed by the airplane
manufacturer containing general
information about the make and
model of an airplane. The airplane
owner’s manual is not FAA-approved
and is not specific to a particular serial
numbered airplane. This manual is not
kept current, and therefore cannot be
substituted for the AFM/POH.
AIRPORT/FACILITY
DIRECTORY—
A publication designed primarily as a
pilot’s operational manual containing
all airports, seaplane bases, and
heliports open to the public including
communications data, navigational
facilities, and certain special notices
and procedures. This publication is
issued in seven volumes according to
geographical area.
allowing the airplane to fly hands-off
at any given airspeed.
ADVERSE YAW—A condition of
flight in which the nose of an airplane
tends to yaw toward the outside of the
turn. This is caused by the higher
induced drag on the outside wing,
which is also producing more lift.
Induced drag is a by-product of the lift
associated with the outside wing.
AERODYNAMIC CEILING—
The point (altitude) at which, as the
indicated airspeed decreases with altitude,
it progressively merges with the
low speed buffet boundary where prestall
buffet occurs for the airplane at a
load factor of 1.0 G.
AERODYNAMICS—The science of
the action of air on an object, and with
the motion of air on other gases.
Aerodynamics deals with the
production of lift by the aircraft, the
relative wind, and the atmosphere.
AILERONS—Primary flight control
surfaces mounted on the trailing edge
of an airplane wing, near the tip.
Ailerons control roll about the longitudinal
axis.
AIR START—The act or instance of
starting an aircraft’s engine while in
flight, especially a jet engine after
flameout.
AIRCRAFT LOGBOOKS—
Journals containing a record of total
operating time, repairs, alterations or
inspections performed, and all
Airworthiness Directive (AD) notes
complied with. A maintenance
logbook should be kept for the
airframe, each engine, and each
propeller.
AIRFOIL—An airfoil is any surface,
such as a wing, propeller, rudder, or
G-1
Glossary.qxd 5/7/04 10:46 AM Page G-1
G-2
AIRWORTHINESS—A condition
in which the aircraft conforms to its
type certificated design including
supplemental type certificates, and
field approved alterations. The
aircraft must also be in a condition for
safe flight as determined by annual,
100 hour, preflight and any other
required inspections.
AIRWORTHINESS
CERTIFICATE—
A certificate issued by the FAA to all
aircraft that have been proven to meet
the minimum standards set down by
the Code of Federal Regulations.
AIRWORTHINESS
DIRECTIVE—A regulatory notice
sent out by the FAA to the registered
owner of an aircraft informing the
owner of a condition that prevents the
aircraft from continuing to meet
its conditions for airworthiness.
Airworthiness Directives (AD notes)
must be complied with within the
required time limit, and the fact of
compliance, the date of compliance,
and the method of compliance must be
recorded in the aircraft’s maintenance
records.
ALPHA MODE OF
OPERATION—The operation of a
turboprop engine that includes all of
the flight operations, from takeoff to
landing. Alpha operation is typically
between 95 percent to 100 percent of
the engine operating speed.
ALTERNATE AIR—A device
which opens, either automatically
or manually, to allow induction airflow
to continue should the primary
induction air opening become
blocked.
ALTERNATE STATIC SOURCE—
A manual port that when opened
allows the pitot static instruments to
sense static pressure from an alternate
location should the primary static port
become blocked.
ALTERNATOR/GENERATOR—A
device that uses engine power to generate
electrical power.
ALTIMETER—A flight instrument
that indicates altitude by sensing
pressure changes.
pitch, which is the up and down
movement of the airplane’s nose.
ATTITUDE— The position of an
aircraft as determined by the
relationship of its axes and a reference,
usually the earth’s horizon.
AUTOKINESIS—This is caused by
staring at a single point of light
against a dark background for more
than a few seconds. After a few
moments, the light appears to move
on its own.
AUTOPILOT—An automatic flight
control system which keeps an aircraft
in level flight or on a set course.
Automatic pilots can be directed by
the pilot, or they may be coupled to a
radio navigation signal.
AXES OF AN AIRCRAFT—Three
imaginary lines that pass through an
aircraft’s center of gravity. The axes
can be considered as imaginary axles
around which the aircraft turns. The
three axes pass through the center of
gravity at 90° angles to each other.
The axis from nose to tail is the
longitudinal axis, the axis that passes
from wingtip to wingtip is the lateral
axis, and the axis that passes vertically
through the center of gravity is the
vertical axis.
AXIAL FLOW COMPRESSOR—
Atype of compressor used in a turbine
engine in which the airflow through
the compressor is essentially linear.
An axial-flow compressor is made up
of several stages of alternate rotors
and stators. The compressor ratio is
determined by the decrease in area of
the succeeding stages.
BACK SIDE OF THE POWER
CURVE— Flight regime in which
flight at a higher airspeed requires a
lower power setting and a lower
airspeed requires a higher power
setting in order to maintain altitude.
BALKED LANDING—
A go-around.
BALLAST—Removable or permanently
installed weight in an aircraft
ALTITUDE (AGL)—The actual
height above ground level (AGL) at
which the aircraft is flying.
ALTITUDE (MSL)—The actual
height above mean sea level (MSL) at
which the aircraft is flying.
ALTITUDE CHAMBER—A device
that simulates high altitude conditions
by reducing the interior pressure. The
occupants will suffer from the same
physiological conditions as flight at
high altitude in an unpressurized
aircraft.
ALTITUDE ENGINE—
A reciprocating aircraft engine having
a rated takeoff power that is
producible from sea level to an
established higher altitude.
ANGLE OF ATTACK—The acute
angle between the chord line of the
airfoil and the direction of the relative
wind.
ANGLE OF INCIDENCE—
The angle formed by the chord line of
the wing and a line parallel to the
longitudinal axis of the airplane.
ANNUAL INSPECTION—
A complete inspection of an aircraft
and engine, required by the Code
of Federal Regulations, to be
accomplished every 12 calendar
months on all certificated aircraft.
Only an A&P technician holding an
Inspection Authorization can conduct
an annual inspection.
ANTI-ICING—The prevention of
the formation of ice on a surface. Ice
may be prevented by using heat or by
covering the surface with a chemical
that prevents water from reaching the
surface. Anti-icing should not be confused
with deicing, which is the
removal of ice after it has formed on
the surface.
ATTITUDE INDICATOR—
An instrument which uses an artificial
horizon and miniature airplane to
depict the position of the airplane in
relation to the true horizon. The
attitude indicator senses roll as well as
Glossary.qxd 5/7/04 10:46 AM Page G-2
G-3
used to bring the center of gravity into
the allowable range.
BALLOON—The result of a too
aggressive flare during landing
causing the aircraft to climb.
BASIC EMPTY WEIGHT
(GAMA)—Basic empty weight
includes the standard empty weight
plus optional and special equipment
that has been installed.
BEST ANGLE OF CLIMB (VX)—
The speed at which the aircraft will
produce the most gain in altitude in a
given distance.
BEST GLIDE—The airspeed in
which the aircraft glides the furthest
for the least altitude lost when in
non-powered flight.
BEST RATE OF CLIMB (VY)—
The speed at which the aircraft will
produce the most gain in altitude in
the least amount of time.
BLADE FACE—The flat portion of a
propeller blade, resembling the
bottom portion of an airfoil.
BLEED AIR—Compressed air
tapped from the compressor stages of
a turbine engine by use of ducts and
tubing. Bleed air can be used for
deice, anti-ice, cabin pressurization,
heating, and cooling systems.
BLEED VALVE—In a turbine
engine, a flapper valve, a popoff
valve, or a bleed band designed to
bleed off a portion of the compressor
air to the atmosphere. Used to
maintain blade angle of attack and
provide stall-free engine acceleration
and deceleration.
BOOST PUMP—An electrically
driven fuel pump, usually of the
centrifugal type, located in one of the
fuel tanks. It is used to provide fuel to
the engine for starting and providing
fuel pressure in the event of failure of
the engine driven pump. It also
pressurizes the fuel lines to prevent
vapor lock.
CAMBERED—The camber of an
airfoil is the characteristic curve of its
upper and lower surfaces. The upper
camber is more pronounced, while the
lower camber is comparatively flat.
This causes the velocity of the airflow
immediately above the wing to be
much higher than that below the wing.
CARBURETOR ICE— Ice that
forms inside the carburetor due to the
temperature drop caused by the
vaporization of the fuel. Induction
system icing is an operational hazard
because it can cut off the flow of the
fuel/air charge or vary the fuel/air
ratio.
CARBURETOR—1. Pressure: A
hydromechanical device employing a
closed feed system from the fuel
pump to the discharge nozzle. It
meters fuel through fixed jets
according to the mass airflow through
the throttle body and discharges it
under a positive pressure. Pressure
carburetors are distinctly different
from float-type carburetors, as they do
not incorporate a vented float
chamber or suction pickup from a
discharge nozzle located in the venturi
tube. 2. Float-type: Consists
essentially of a main air passage
through which the engine draws its
supply of air, a mechanism to control
the quantity of fuel discharged in
relation to the flow of air, and a means
of regulating the quantity of fuel/air
mixture delivered to the engine
cylinders.
CASCADE REVERSER—A thrust
reverser normally found on turbofan
engines in which a blocker door and a
series of cascade vanes are used to
redirect exhaust gases in a forward
direction.
CENTER OF GRAVITY (CG)—
The point at which an airplane would
balance if it were possible to suspend
it at that point. It is the mass center of
the airplane, or the theoretical point at
which the entire weight of the airplane
is assumed to be concentrated. It may
be expressed in inches from the reference
datum, or in percent of mean
aerodynamic chord (MAC). The location
depends on the distribution of
weight in the airplane.
BUFFETING—The beating of an
aerodynamic structure or surface by
unsteady flow, gusts, etc.; the irregular
shaking or oscillation of a vehicle
component owing to turbulent air or
separated flow.
BUS BAR—An electrical power
distribution point to which several
circuits may be connected. It is often a
solid metal strip having a number of
terminals installed on it.
BUS TIE—A switch that connects
two or more bus bars. It is usually
used when one generator fails and
power is lost to its bus. By closing the
switch, the operating generator
powers both busses.
BYPASS AIR—The part of a
turbofan’s induction air that bypasses
the engine core.
BYPASS RATIO—The ratio of the
mass airflow in pounds per second
through the fan section of a turbofan
engine to the mass airflow that passes
through the gas generator portion of
the engine. Or, the ratio between fan
mass airflow (lb/sec.) and core engine
mass airflow (lb/sec.).
CABIN PRESSURIZATION—A
condition where pressurized air is
forced into the cabin simulating
pressure conditions at a much lower
altitude and increasing the aircraft
occupants comfort.
CALIBRATED AIRSPEED
(CAS)—Indicated airspeed corrected
for installation error and instrument
error. Although manufacturers attempt
to keep airspeed errors to a minimum,
it is not possible to eliminate all errors
throughout the airspeed operating
range. At certain airspeeds and with
certain flap settings, the installation
and instrument errors may total
several knots. This error is generally
greatest at low airspeeds. In the
cruising and higher airspeed ranges,
indicated airspeed and calibrated
airspeed are approximately the same.
Refer to the airspeed calibration chart
to correct for possible airspeed errors.
Glossary.qxd 5/7/04 10:46 AM Page G-3
G-4
CENTER-OF-GRAVITY
LIMITS—The specified forward and
aft points within which the CG must
be located during flight. These limits
are indicated on pertinent airplane
specifications.
CENTER-OF-GRAVITY
RANGE—The distance between the
forward and aft CG limits indicated on
pertinent airplane specifications.
CENTRIFUGAL
FLOW COMPRESSOR—
An impeller-shaped device that receives
air at its center and slings air outward at
high velocity into a diffuser for increased
pressure. Also referred to as a radial outflow
compressor.
CHORD LINE—An imaginary
straight line drawn through an airfoil
from the leading edge to the trailing
edge.
CIRCUIT BREAKER—
A circuit-protecting device that opens
the circuit in case of excess current
flow. A circuit breakers differs from a
fuse in that it can be reset without
having to be replaced.
CLEAR AIR TURBULENCE—
Turbulence not associated with any
visible moisture.
CLIMB GRADIENT—The ratio
between distance traveled and altitude
gained.
COCKPIT RESOURCE
MANAGEMENT—Techniques
designed to reduce pilot errors and
manage errors that do occur utilizing
cockpit human resources. The
assumption is that errors are going to
happen in a complex system with
error-prone humans.
COEFFICIENT OF LIFT—See
LIFT COEFFICIENT.
COFFIN CORNER—The flight
regime where any increase in airspeed
will induce high speed mach buffet
and any decrease in airspeed will
induce low speed mach buffet.
CONDITION LEVER—In a turbine
engine, a powerplant control that controls
the flow of fuel to the engine.
The condition lever sets the desired
engine r.p.m. within a narrow range
between that appropriate for ground
and flight operations.
CONFIGURATION—This is a
general term, which normally refers to
the position of the landing gear
and flaps.
CONSTANT SPEED
PROPELLER— A controllablepitch
propeller whose pitch is
automatically varied in flight by a
governor to maintain a constant r.p.m.
in spite of varying air loads.
CONTROL TOUCH—The ability to
sense the action of the airplane and its
probable actions in the immediate
future, with regard to attitude and
speed variations, by sensing and
evaluation of varying pressures and
resistance of the control surfaces
transmitted through the cockpit flight
controls.
CONTROLLABILITY—A measure
of the response of an aircraft relative
to the pilot’s flight control inputs.
CONTROLLABLE PITCH
PROPELLER—Apropeller in which
the blade angle can be changed during
flight by a control in the cockpit.
CONVENTIONAL LANDING
GEAR—Landing gear employing a
third rear-mounted wheel. These
airplanes are also sometimes referred
to as tailwheel airplanes.
COORDINATED FLIGHT—
Application of all appropriate flight
and power controls to prevent slipping
or skidding in any flight condition.
COORDINATION—The ability to
use the hands and feet together
subconsciously and in the proper
relationship to produce desired results
in the airplane.
CORE AIRFLOW—Air drawn into
the engine for the gas generator.
COMBUSTION CHAMBER—The
section of the engine into which fuel
is injected and burned.
COMMON TRAFFIC
ADVISORY FREQUENCY—The
common frequency used by airport
traffic to announce position reports in
the vicinity of the airport.
COMPLEX AIRCRAFT—
An aircraft with retractable landing
gear, flaps, and a controllable-pitch
propeller, or is turbine powered.
COMPRESSION RATIO—1. In a
reciprocating engine, the ratio of the
volume of an engine cylinder with the
piston at the bottom center to the
volume with the piston at top center.
2. In a turbine engine, the ratio of the
pressure of the air at the discharge to
the pressure of air at the inlet.
COMPRESSOR BLEED AIR—
See BLEED AIR.
COMPRESSOR BLEED
VALVES—See BLEED VALVE.
COMPRESSOR SECTION— The
section of a turbine engine that
increases the pressure and density of
the air flowing through the engine.
COMPRESSOR STALL—In gas
turbine engines, a condition in an
axial-flow compressor in which one
or more stages of rotor blades fail to
pass air smoothly to the succeeding
stages. Astall condition is caused by a
pressure ratio that is incompatible
with the engine r.p.m. Compressor
stall will be indicated by a rise in
exhaust temperature or r.p.m.
fluctuation, and if allowed to
continue, may result in flameout and
physical damage to the engine.
COMPRESSOR SURGE—Asevere
compressor stall across the entire
compressor that can result in severe
damage if not quickly corrected. This
condition occurs with a complete
stoppage of airflow or a reversal of
airflow.
Glossary.qxd 5/7/04 10:46 AM Page G-4
G-5
COWL FLAPS—Devices arranged
around certain air-cooled engine
cowlings which may be opened or
closed to regulate the flow of air
around the engine.
CRAB—A flight condition in which
the nose of the airplane is pointed into
the wind a sufficient amount to counteract
a crosswind and maintain a
desired track over the ground.
CRAZING—Small fractures in
aircraft windshields and windows
caused from being exposed to the
ultraviolet rays of the sun and
temperature extremes.
CRITICAL ALTITUDE—
The maximum altitude under standard
atmospheric conditions at which a
turbocharged engine can produce its
rated horsepower.
CRITICAL ANGLE
OF ATTACK—The angle of attack at
which a wing stalls regardless of
airspeed, flight attitude, or weight.
CRITICAL ENGINE—The engine
whose failure has the most adverse
effect on directional control.
CROSS CONTROLLED—
A condition where aileron deflection
is in the opposite direction of rudder
deflection.
CROSSFEED—Asystem that allows
either engine on a twin-engine
airplane to draw fuel from any fuel
tank.
CROSSWIND COMPONENT—
The wind component, measured in
knots, at 90° to the longitudinal axis
of the runway.
CURRENT LIMITER—A device
that limits the generator output to a
level within that rated by the
generator manufacturer.
DATUM (REFERENCE
DATUM)—An imaginary vertical
plane or line from which all
measurements of moment arm are
taken. The datum is established by the
manufacturer. Once the datum has
been selected, all moment arms and
parasite drag to compensate for the
additional induced drag caused by the
down aileron. This balancing of the
drag forces helps minimize adverse
yaw.
DIFFUSION—Reducing the velocity
of air causing the pressure to increase.
DIRECTIONAL STABILITY—
Stability about the vertical axis of an
aircraft, whereby an aircraft tends to
return, on its own, to flight aligned
with the relative wind when disturbed
from that equilibrium state. The
vertical tail is the primary contributor
to directional stability, causing an
airplane in flight to align with the
relative wind.
DITCHING—Emergency landing in
water.
DOWNWASH—
Air deflected perpendicular to the
motion of the airfoil.
DRAG—An aerodynamic force on a
body acting parallel and opposite to
the relative wind. The resistance of
the atmosphere to the relative motion
of an aircraft. Drag opposes thrust and
limits the speed of the airplane.
DRAG CURVE—
A visual representation of the amount
of drag of an aircraft at various
airspeeds.
DRIFT ANGLE—Angle between
heading and track.
DUCTED-FAN ENGINE—
An engine-propeller combination that
has the propeller enclosed in a radial
shroud. Enclosing the propeller
improves the efficiency of the
propeller.
DUTCH ROLL—A combination of
rolling and yawing oscillations that
normally occurs when the dihedral
effects of an aircraft are more
powerful than the directional stability.
Usually dynamically stable but
objectionable in an airplane because
of the oscillatory nature.
the location of CG range are measured
from this point.
DECOMPRESSION SICKNESS—
A condition where the low pressure at
high altitudes allows bubbles of
nitrogen to form in the blood and
joints causing severe pain. Also
known as the bends.
DEICER BOOTS—Inflatable rubber
boots attached to the leading edge of
an airfoil. They can be sequentially
inflated and deflated to break away ice
that has formed over their surface.
DEICING—Removing ice after it
has formed.
DELAMINATION—The separation
of layers.
DENSITY ALTITUDE—
This altitude is pressure altitude corrected
for variations from standard
temperature. When conditions are
standard, pressure altitude and density
altitude are the same. If the temperature
is above standard, the density altitude
is higher than pressure altitude. If
the temperature is below standard, the
density altitude is lower than pressure
altitude. This is an important altitude
because it is directly related to the
airplane’s performance.
DESIGNATED PILOT
EXAMINER (DPE)—An individual
designated by the FAA to administer
practical tests to pilot applicants.
DETONATION—
The sudden release of heat energy
from fuel in an aircraft engine caused
by the fuel-air mixture reaching its
critical pressure and temperature.
Detonation occurs as a violent
explosion rather than a smooth
burning process.
DEWPOINT—The temperature at
which air can hold no more water.
DIFFERENTIAL AILERONS—
Control surface rigged such that the
aileron moving up moves a greater
distance than the aileron moving
down. The up aileron produces extra
Glossary.qxd 5/7/04 10:46 AM Page G-5
G-6
DYNAMIC HYDROPLANING—A
condition that exists when landing on
a surface with standing water deeper
than the tread depth of the tires. When
the brakes are applied, there is a
possibility that the brake will lock up
and the tire will ride on the surface of
the water, much like a water ski.
When the tires are hydroplaning,
directional control and braking action
are virtually impossible. An effective
anti-skid system can minimize the
effects of hydroplaning.
DYNAMIC STABILITY—
The property of an aircraft that causes
it, when disturbed from straight-andlevel
flight, to develop forces or
moments that restore the original
condition of straight and level.
ELECTRICAL BUS—
See BUS BAR.
ELECTROHYDRAULIC—
Hydraulic control which is electrically
actuated.
ELEVATOR—
The horizontal, movable primary
control surface in the tail section, or
empennage, of an airplane. The
elevator is hinged to the trailing edge
of the fixed horizontal stabilizer.
EMERGENCY LOCATOR
TRANSMITTER—A small, selfcontained
radio transmitter that will
automatically, upon the impact of a
crash, transmit an emergency signal
on 121.5, 243.0, or 406.0 MHz.
EMPENNAGE—The section of the
airplane that consists of the vertical
stabilizer, the horizontal stabilizer,
and the associated control surfaces.
ENGINE PRESSURE RATIO
(EPR)—The ratio of turbine
discharge pressure divided by
compressor inlet pressure that is used
as an indication of the amount of
thrust being developed by a turbine
engine.
ENVIRONMENTAL SYSTEMS—
In an aircraft, the systems, including
the supplemental oxygen systems, air
conditioning systems, heaters, and
FIXED SHAFT TURBOPROP
ENGINE—A turboprop engine
where the gas producer spool is
directly connected to the output shaft.
FIXED-PITCH PROPELLERS—
Propellers with fixed blade angles.
Fixed-pitch propellers are designed as
climb propellers, cruise propellers, or
standard propellers.
FLAPS—Hinged portion of the
trailing edge between the ailerons and
fuselage. In some aircraft, ailerons
and flaps are interconnected to
produce full-span “flaperons.” In
either case, flaps change the lift and
drag on the wing.
FLAT PITCH—
A propeller configuration when the
blade chord is aligned with the direction
of rotation.
FLICKER VERTIGO—
A disorientating condition caused
from flickering light off the blades of
the propeller.
FLIGHT DIRECTOR—An automatic
flight control system in which
the commands needed to fly the airplane
are electronically computed and
displayed on a flight instrument. The
commands are followed by the human
pilot with manual control inputs or, in
the case of an autopilot system, sent to
servos that move the flight controls.
FLIGHT IDLE—Engine speed,
usually in the 70-80 percent range, for
minimum flight thrust.
FLOATING—A condition when
landing where the airplane does not
settle to the runway due to excessive
airspeed.
FORCE (F)—The energy applied to
an object that attempts to cause the
object to change its direction, speed,
or motion. In aerodynamics, it is
expressed as F, T (thrust), L (lift), W
(weight), or D (drag), usually in
pounds.
FORM DRAG—The part of parasite
drag on a body resulting from the
pressurization systems, which make it
possible for an occupant to function at
high altitude.
EQUILIBRIUM—A condition that
exists within a body when the sum of
the moments of all of the forces acting
on the body is equal to zero. In
aerodynamics, equilibrium is when all
opposing forces acting on an aircraft
are balanced (steady, unaccelerated
flight conditions).
EQUIVALENT SHAFT
HORSEPOWER (ESHP)—
A measurement of the total horsepower
of a turboprop engine, including
that provided by jet thrust.
EXHAUST GAS TEMPERATURE
(EGT)—The temperature of the
exhaust gases as they leave the
cylinders of a reciprocating engine or
the turbine section of a turbine engine.
EXHAUST MANIFOLD—The part
of the engine that collects exhaust
gases leaving the cylinders.
EXHAUST—The rear opening of a
turbine engine exhaust duct. The
nozzle acts as an orifice, the size of
which determines the density and
velocity of the gases as they emerge
from the engine.
FALSE HORIZON—An optical
illusion where the pilot confuses a row
of lights along a road or other straight
line as the horizon.
FALSE START—
See HUNG START.
FEATHERING PROPELLER
(FEATHERED)—A controllable
pitch propeller with a pitch range
sufficient to allow the blades to be
turned parallel to the line of flight to
reduce drag and prevent further
damage to an engine that has been
shut down after a malfunction.
FIXATION—
A psychological condition where the
pilot fixes attention on a single source
of information and ignores all
other sources.
Glossary.qxd 5/7/04 10:46 AM Page G-6
G-7
integrated effect of the static pressure
acting normal to its surface resolved
in the drag direction.
FORWARD SLIP—A slip in which
the airplane’s direction of motion continues
the same as before the slip was
begun. In a forward slip, the airplane’s
longitudinal axis is at an angle to its
flightpath.
FREE POWER TURBINE
ENGINE—A turboprop engine
where the gas producer spool is on a
separate shaft from the output shaft.
The free power turbine spins
independently of the gas producer and
drives the output shaft.
FRICTION DRAG—The part of
parasitic drag on a body resulting
from viscous shearing stresses over its
wetted surface.
FRISE-TYPE AILERON—Aileron
having the nose portion projecting
ahead of the hinge line. When the
trailing edge of the aileron moves up,
the nose projects below the wing’s
lower surface and produces some
parasite drag, decreasing the amount
of adverse yaw.
FUEL CONTROL UNIT—
The fuel-metering device used on a
turbine engine that meters the proper
quantity of fuel to be fed into the
burners of the engine. It integrates the
parameters of inlet air temperature,
compressor speed, compressor
discharge pressure, and exhaust gas
temperature with the position of the
cockpit power control lever.
FUEL EFFICIENCY—Defined as
the amount of fuel used to produce a
specific thrust or horsepower divided
by the total potential power contained
in the same amount of fuel.
FUEL HEATERS—A radiator-like
device which has fuel passing through
the core. A heat exchange occurs to
keep the fuel temperature above the
freezing point of water so that
entrained water does not form ice
crystals, which could block fuel flow.
FUEL INJECTION—
A fuel metering system used on some
aircraft reciprocating engines in
GO-AROUND—
Terminating a landing approach.
GOVERNING RANGE—The range
of pitch a propeller governor can
control during flight.
GOVERNOR—A control which
limits the maximum rotational speed
of a device.
GROSS WEIGHT—
The total weight of a fully loaded
aircraft including the fuel, oil, crew,
passengers, and cargo.
GROUND ADJUSTABLE TRIM
TAB—A metal trim tab on a control
surface that is not adjustable in flight.
Bent in one direction or another while
on the ground to apply trim forces to
the control surface.
GROUND EFFECT—A condition
of improved performance encountered
when an airplane is operating
very close to the ground. When an
airplane’s wing is under the influence
of ground effect, there is a reduction
in upwash, downwash, and wingtip
vortices. As a result of the reduced
wingtip vortices, induced drag is
reduced.
GROUND IDLE—Gas turbine
engine speed usually 60-70 percent of
the maximum r.p.m. range, used as a
minimum thrust setting for ground
operations.
GROUND LOOP—A sharp, uncontrolled
change of direction of an
airplane on the ground.
GROUND POWER UNIT (GPU)—
A type of small gas turbine whose
purpose is to provide electrical power,
and/or air pressure for starting aircraft
engines. Aground unit is connected to
the aircraft when needed. Similar to
an aircraft-installed auxiliary power
unit.
GROUNDSPEED (GS)—The actual
speed of the airplane over the ground.
It is true airspeed adjusted for
wind. Groundspeed decreases with a
headwind, and increases with
a tailwind.
which a constant flow of fuel is fed to
injection nozzles in the heads of all
cylinders just outside of the intake
valve. It differs from sequential fuel
injection in which a timed charge of
high-pressure fuel is sprayed directly
into the combustion chamber of the
cylinder.
FUEL LOAD—The expendable part
of the load of the airplane. It includes
only usable fuel, not fuel required to
fill the lines or that which remains
trapped in the tank sumps.
FUEL TANK SUMP—A sampling
port in the lowest part of the fuel tank
that the pilot can utilize to check for
contaminants in the fuel.
FUSELAGE—The section of the
airplane that consists of the cabin
and/or cockpit, containing seats for
the occupants and the controls for the
airplane.
GAS GENERATOR—The basic
power producing portion of a gas
turbine engine and excluding such
sections as the inlet duct, the
fan section, free power turbines,
and tailpipe. Each manufacturer
designates what is included as the gas
generator, but generally consists of
the compressor, diffuser, combustor,
and turbine.
GAS TURBINE ENGINE—A form
of heat engine in which burning fuel
adds energy to compressed air and
accelerates the air through the
remainder of the engine. Some of the
energy is extracted to turn the air
compressor, and the remainder
accelerates the air to produce thrust.
Some of this energy can be converted
into torque to drive a propeller or a
system of rotors for a helicopter.
GLIDE RATIO—The ratio between
distance traveled and altitude lost
during non-powered flight.
GLIDEPATH—The path of an
aircraft relative to the ground while
approaching a landing.
GLOBAL POSITION SYSTEM
(GPS)—A satellite-based radio positioning,
navigation, and time-transfer
system.
Glossary.qxd 5/7/04 10:46 AM Page G-7
G-8
GROUND TRACK—The aircraft’s
path over the ground when in flight.
GUST PENETRATION SPEED—
The speed that gives the greatest
margin between the high and low
mach speed buffets.
GYROSCOPIC PRECESSION—
An inherent quality of rotating bodies,
which causes an applied force to be
manifested 90º in the direction of
rotation from the point where the
force is applied.
HAND PROPPING—Starting an
engine by rotating the propeller by
hand.
HEADING—The direction in which
the nose of the aircraft is pointing
during flight.
HEADING BUG—A marker on the
heading indicator that can be rotated
to a specific heading for reference
purposes, or to command an autopilot
to fly that heading.
HEADING INDICATOR—
An instrument which senses airplane
movement and displays heading based
on a 360º azimuth, with the final zero
omitted. The heading indicator, also
called a directional gyro, is fundamentally
a mechanical instrument
designed to facilitate the use of the
magnetic compass. The heading indicator
is not affected by the forces that
make the magnetic compass difficult
to interpret.
HEADWIND COMPONENT—The
component of atmospheric winds that
acts opposite to the aircraft’s flightpath.
HIGH PERFORMANCE
AIRCRAFT—An aircraft with an
engine of more than 200 horsepower.
HORIZON—The line of sight
boundary between the earth and the
sky.
HORSEPOWER—
The term, originated by inventor
James Watt, means the amount of
work a horse could do in one second.
engine. Some igniters resemble spark
plugs, while others, called glow plugs,
have a coil of resistance wire that
glows red hot when electrical current
flows through the coil.
IMPACT ICE—Ice that forms on the
wings and control surfaces or on the
carburetor heat valve, the walls of the
air scoop, or the carburetor units
during flight. Impact ice collecting on
the metering elements of the
carburetor may upset fuel metering or
stop carburetor fuel flow.
INCLINOMETER—An instrument
consisting of a curved glass tube,
housing a glass ball, and damped with
a fluid similar to kerosene. It may be
used to indicate inclination, as a level,
or, as used in the turn indicators, to
show the relationship between gravity
and centrifugal force in a turn.
INDICATED AIRSPEED (IAS)—
The direct instrument reading
obtained from the airspeed indicator,
uncorrected for variations in atmospheric
density, installation error, or
instrument error. Manufacturers use
this airspeed as the basis for determining
airplane performance. Takeoff,
landing, and stall speeds listed in the
AFM or POH are indicated airspeeds
and do not normally vary with altitude
or temperature.
INDICATED ALTITUDE—
The altitude read directly from the
altimeter (uncorrected) when it is set
to the current altimeter setting.
INDUCED DRAG—That part of
total drag which is created by the
production of lift. Induced drag
increases with a decrease in airspeed.
INDUCTION MANIFOLD—The
part of the engine that distributes
intake air to the cylinders.
INERTIA—The opposition which a
body offers to a change of motion.
INITIAL CLIMB—This stage of the
climb begins when the airplane leaves
the ground, and a pitch attitude has
One horsepower equals 550
foot-pounds per second, or 33,000
foot-pounds per minute.
HOT START—In gas turbine
engines, a start which occurs with
normal engine rotation, but exhaust
temperature exceeds prescribed
limits. This is usually caused by an
excessively rich mixture in the
combustor. The fuel to the engine
must be terminated immediately to
prevent engine damage.
HUNG START—In gas turbine
engines, a condition of normal light
off but with r.p.m. remaining at some
low value rather than increasing to the
normal idle r.p.m. This is often the
result of insufficient power to the
engine from the starter. In the event of
a hung start, the engine should be shut
down.
HYDRAULICS—The branch of
science that deals with the
transmission of power by incompressible
fluids under pressure.
HYDROPLANING—A condition
that exists when landing on a surface
with standing water deeper than the
tread depth of the tires. When the
brakes are applied, there is a
possibility that the brake will lock up
and the tire will ride on the surface of
the water, much like a water ski.
When the tires are hydroplaning,
directional control and braking action
are virtually impossible. An effective
anti-skid system can minimize the
effects of hydroplaning.
HYPOXIA—A lack of sufficient
oxygen reaching the body tissues.
IFR (INSTRUMENT FLIGHT
RULES)—Rules that govern the
procedure for conducting flight in
weather conditions below VFR
weather minimums. The term “IFR”
also is used to define weather
conditions and the type of flight plan
under which an aircraft is operating.
IGNITER PLUGS—The electrical
device used to provide the spark for
starting combustion in a turbine
Glossary.qxd 5/7/04 10:46 AM Page G-8
G-9
been established to climb away from
the takeoff area.
INTEGRAL FUEL TANK—
A portion of the aircraft structure,
usually a wing, which is sealed off and
used as a fuel tank. When a wing is
used as an integral fuel tank, it is
called a “wet wing.”
INTERCOOLER—A device used to
reduce the temperature of the
compressed air before it enters the
fuel metering device. The resulting
cooler air has a higher density, which
permits the engine to be operated with
a higher power setting.
INTERNAL COMBUSTION
ENGINES—An engine that produces
power as a result of expanding hot
gases from the combustion of fuel and
air within the engine itself. A steam
engine where coal is burned to heat up
water inside the engine is an example
of an external combustion engine.
INTERSTAGE TURBINE
TEMPERATURE (ITT)—The temperature
of the gases between the high
pressure and low pressure turbines.
INVERTER—An electrical device
that changes DC to AC power.
ISA (INTERNATIONAL
STANDARD ATMOSPHERE)—
Standard atmospheric conditions
consisting of a temperature of 59°F
(15°C), and a barometric pressure of
29.92 in. Hg. (1013.2 mb) at sea level.
ISA values can be calculated for
various altitudes using a standard
lapse rate of approximately 2°C per
1,000 feet.
JET POWERED AIRPLANE—An
aircraft powered by a turbojet or
turbofan engine.
KINESTHESIA—The sensing of
movements by feel.
LATERAL AXIS—An imaginary
line passing through the center of
gravity of an airplane and extending
across the airplane from wingtip
to wingtip.
the coefficient of drag for any given
angle of attack.
LIFT-OFF—The act of becoming
airborne as a result of the wings
lifting the airplane off the ground, or
the pilot rotating the nose up,
increasing the angle of attack to start a
climb.
LIMIT LOAD FACTOR—Amount
of stress, or load factor, that an aircraft
can withstand before structural
damage or failure occurs.
LOAD FACTOR—The ratio of the
load supported by the airplane’s wings
to the actual weight of the aircraft and
its contents. Also referred to as
G-loading.
LONGITUDINAL AXIS—
An imaginary line through an aircraft
from nose to tail, passing through its
center of gravity. The longitudinal
axis is also called the roll axis of the
aircraft. Movement of the ailerons
rotates an airplane about its
longitudinal axis.
LONGITUDINAL STABILITY
(PITCHING)—Stability about the
lateral axis. A desirable characteristic
of an airplane whereby it tends to
return to its trimmed angle of attack
after displacement.
MACH—Speed relative to the speed
of sound. Mach 1 is the speed of
sound.
MACH BUFFET—
Airflow separation behind a
shock-wave pressure barrier caused
by airflow over flight surfaces
exceeding the speed of sound.
MACH COMPENSATING
DEVICE—A device to alert the pilot
of inadvertent excursions beyond its
certified maximum operating speed.
MACH CRITICAL—The MACH
speed at which some portion of the
airflow over the wing first equals
MACH 1.0. This is also the speed at
which a shock wave first appears on
the airplane.
LATERAL STABILITY
(ROLLING)—The stability about the
longitudinal axis of an aircraft.
Rolling stability or the ability of an
airplane to return to level flight due to
a disturbance that causes one of the
wings to drop.
LEAD-ACID BATTERY—
A commonly used secondary cell
having lead as its negative plate and
lead peroxide as its positive plate.
Sulfuric acid and water serve as the
electrolyte.
LEADING EDGE DEVICES—
High lift devices which are found on
the leading edge of the airfoil. The
most common types are fixed slots,
movable slats, and leading edge flaps.
LEADING EDGE—The part of an
airfoil that meets the airflow first.
LEADING EDGE FLAP—
A portion of the leading edge of an
airplane wing that folds downward to
increase the camber, lift, and drag of
the wing. The leading-edge flaps are
extended for takeoffs and landings to
increase the amount of aerodynamic
lift that is produced at any given
airspeed.
LICENSED EMPTY WEIGHT—
The empty weight that consists of the
airframe, engine(s), unusable fuel,
and undrainable oil plus standard and
optional equipment as specified in the
equipment list. Some manufacturers
used this term prior to GAMA
standardization.
LIFT—One of the four main forces
acting on an aircraft. On a fixed-wing
aircraft, an upward force created by
the effect of airflow as it passes over
and under the wing.
LIFT COEFFICIENT— A coefficient
representing the lift of a given
airfoil. Lift coefficient is obtained by
dividing the lift by the free-stream
dynamic pressure and the representative
area under consideration.
LIFT/DRAG RATIO—
The efficiency of an airfoil section. It
is the ratio of the coefficient of lift to
Glossary.qxd 5/7/04 10:46 AM Page G-9
G-10
MACH TUCK—Acondition that can
occur when operating a swept-wing
airplane in the transonic speed range.
A shock wave could form in the root
portion of the wing and cause the
air behind it to separate. This
shock-induced separation causes the
center of pressure to move aft. This,
combined with the increasing amount
of nose down force at higher speeds to
maintain left flight, causes the nose to
“tuck.” If not corrected, the airplane
could enter a steep, sometimes
unrecoverable dive.
MAGNETIC COMPASS—A device
for determining direction measured
from magnetic north.
MAIN GEAR—The wheels of an
aircraft’s landing gear that supports
the major part of the aircraft’s weight.
MANEUVERABILITY—Ability of
an aircraft to change directions along
a flightpath and withstand the stresses
imposed upon it.
MANEUVERING SPEED (VA) —
The maximum speed where full,
abrupt control movement can be used
without overstressing the airframe.
MANIFOLD PRESSURE (MP)—
The absolute pressure of the fuel/air
mixture within the intake manifold,
usually indicated in inches of
mercury.
MAXIMUM ALLOWABLE
TAKEOFF POWER—The maximum
power an engine is allowed to
develop for a limited period of time;
usually about one minute.
MAXIMUM LANDING
WEIGHT—The greatest weight that
an airplane normally is allowed to
have at landing.
MAXIMUM RAMP WEIGHT—
The total weight of a loaded aircraft,
including all fuel. It is greater than the
takeoff weight due to the fuel that will
be burned during the taxi and runup
operations. Ramp weight may also be
referred to as taxi weight.
allows air to continue flowing over the
top of the wing and delays airflow
separation.
MUSHING—A flight condition
caused by slow speed where the
control surfaces are marginally
effective.
N1, N2, N3—Spool speed expressed in
percent rpm. N1 on a turboprop is the
gas producer speed. N1 on a turbofan
or turbojet engine is the fan speed or
low pressure spool speed. N2 is the
high pressure spool speed on engine
with 2 spools and medium pressure
spool on engines with 3 spools with
N3 being the high pressure spool.
NACELLE—
Astreamlined enclosure on an aircraft
in which an engine is mounted.
On multiengine propeller-driven
airplanes, the nacelle is normally
mounted on the leading edge of the
wing.
NEGATIVE STATIC
STABILITY—The initial tendency
of an aircraft to continue away from
the original state of equilibrium after
being disturbed.
NEGATIVE TORQUE SENSING
(NTS)— A system in a turboprop
engine that prevents the engine from
being driven by the propeller. The
NTS increases the blade angle when
the propellers try to drive the engine.
NEUTRAL STATIC
STABILITY—The initial tendency
of an aircraft to remain in a new
condition after its equilibrium has
been disturbed.
NICKEL-CADMIUM BATTERY
(NICAD)— A battery made up of
alkaline secondary cells. The positive
plates are nickel hydroxide, the
negative plates are cadmium
hydroxide, and potassium hydroxide
is used as the electrolyte.
NORMAL CATEGORY—
An airplane that has a seating
configuration, excluding pilot seats,
MAXIMUM TAKEOFF
WEIGHT—The maximum allowable
weight for takeoff.
MAXIMUM WEIGHT—
The maximum authorized weight of
the aircraft and all of its equipment as
specified in the Type Certificate Data
Sheets (TCDS) for the aircraft.
MAXIMUM ZERO FUEL
WEIGHT (GAMA)—The maximum
weight, exclusive of usable fuel.
MINIMUM CONTROLLABLE
AIRSPEED—An airspeed at which
any further increase in angle of attack,
increase in load factor, or reduction in
power, would result in an immediate
stall.
MINIMUM DRAG SPEED
(L/DMAX)—The point on the total
drag curve where the lift-to-drag ratio
is the greatest. At this speed, total drag
is minimized.
MIXTURE—The ratio of fuel to air
entering the engine’s cylinders.
MMO—Maximum operating speed
expressed in terms of a decimal of
mach speed.
MOMENT ARM—The distance
from a datum to the applied force.
MOMENT INDEX (OR INDEX)—
A moment divided by a constant such
as 100, 1,000, or 10,000. The purpose
of using a moment index is to simplify
weight and balance computations of
airplanes where heavy items and long
arms result in large, unmanageable
numbers.
MOMENT—The product of the
weight of an item multiplied by its
arm. Moments are expressed in
pound-inches (lb-in). Total moment is
the weight of the airplane multiplied
by the distance between the datum and
the CG.
MOVABLE SLAT—A movable
auxiliary airfoil on the leading edge of
a wing. It is closed in normal flight but
extends at high angles of attack. This
Glossary.qxd 5/7/04 10:46 AM Page G-10
G-11
of nine or less, a maximum
certificated takeoff weight of 12,500
pounds or less, and intended for
nonacrobatic operation.
NORMALIZING
(TURBONORMALIZING)—
A turbocharger that maintains sea
level pressure in the induction manifold
at altitude.
OCTANE—The rating system of
aviation gasoline with regard to its
antidetonating qualities.
OVERBOOST—A condition in
which a reciprocating engine has
exceeded the maximum manifold
pressure allowed by the manufacturer.
Can cause damage to engine
components.
OVERSPEED—A condition in
which an engine has produced more
r.p.m. than the manufacturer
recommends, or a condition in which
the actual engine speed is higher than
the desired engine speed as set on the
propeller control.
OVERTEMP—A condition in which
a device has reached a temperature
above that approved by the
manufacturer or any exhaust
temperature that exceeds the
maximum allowable for a given operating
condition or time limit. Can
cause internal damage to an engine.
OVERTORQUE—A condition in
which an engine has produced more
torque (power) than the manufacturer
recommends, or a condition in a
turboprop or turboshaft engine where
the engine power has exceeded the
maximum allowable for a given
operating condition or time limit. Can
cause internal damage to an engine.
PARASITE DRAG—That part of
total drag created by the design or
shape of airplane parts. Parasite drag
increases with an increase in airspeed.
PAYLOAD (GAMA)—The weight
of occupants, cargo, and baggage.
P-FACTOR—A tendency for an
aircraft to yaw to the left due to the
for scheduling fuel flow to the
combustion chambers of a turbine
engine.
POWER—Implies work rate or units
of work per unit of time, and as such,
it is a function of the speed at which
the force is developed. The term
“power required” is generally
associated with reciprocating engines.
POWERPLANT—
A complete engine and propeller
combination with accessories.
PRACTICAL SLIP LIMIT—The
maximum slip an aircraft is capable of
performing due to rudder travel limits.
PRECESSION—The tilting or
turning of a gyro in response to
deflective forces causing slow drifting
and erroneous indications in
gyroscopic instruments.
PREIGNITION—Ignition occurring
in the cylinder before the time of
normal ignition. Preignition is often
caused by a local hot spot in the
combustion chamber igniting the
fuel/air mixture.
PRESSURE ALTITUDE—
The altitude indicated when the
altimeter setting window (barometric
scale) is adjusted to 29.92. This is the
altitude above the standard datum
plane, which is a theoretical plane
where air pressure (corrected to 15ºC)
equals 29.92 in. Hg. Pressure altitude
is used to compute density altitude,
true altitude, true airspeed, and other
performance data.
PROFILE DRAG—The total of the
skin friction drag and form drag for a
two-dimensional airfoil section.
PROPELLER BLADE ANGLE—
The angle between the propeller chord
and the propeller plane of rotation.
PROPELLER LEVER—
The control on a free power turbine
turboprop that controls propeller
speed and the selection for propeller
feathering.
PROPELLER SLIPSTREAM—
The volume of air accelerated behind
a propeller producing thrust.
descending propeller blade on the
right producing more thrust than the
ascending blade on the left. This
occurs when the aircraft’s
longitudinal axis is in a climbing
attitude in relation to the relative
wind. The P-factor would be to the
right if the aircraft had a counterclockwise
rotating propeller.
PILOT’S OPERATING
HANDBOOK (POH)—A document
developed by the airplane
manufacturer and contains the FAAapproved
Airplane Flight Manual
(AFM) information.
PISTON ENGINE—A reciprocating
engine.
PITCH—The rotation of an airplane
about its lateral axis, or on a propeller,
the blade angle as measured from
plane of rotation.
PIVOTAL ALTITUDE—A specific
altitude at which, when an airplane
turns at a given groundspeed, a projecting
of the sighting reference line
to a selected point on the ground will
appear to pivot on that point.
PNEUMATIC SYSTEMS—
The power system in an aircraft used
for operating such items as landing
gear, brakes, and wing flaps with
compressed air as the operating fluid.
PORPOISING—
Oscillating around the lateral axis of
the aircraft during landing.
POSITION LIGHTS—Lights on an
aircraft consisting of a red light on the
left wing, a green light on the right
wing, and a white light on the tail.
CFRs require that these lights be
displayed in flight from sunset to
sunrise.
POSITIVE STATIC STABILITY—
The initial tendency to return to a state
of equilibrium when disturbed from
that state.
POWER DISTRIBUTION BUS—
See BUS BAR.
POWER LEVER—The cockpit
lever connected to the fuel control unit
Glossary.qxd 5/7/04 10:46 AM Page G-11
G-12
PROPELLER
SYNCHRONIZATION—
A condition in which all of
the propellers have their pitch
automatically adjusted to maintain a
constant r.p.m. among all of the
engines of a multiengine aircraft.
PROPELLER—A device for
propelling an aircraft that, when
rotated, produces by its action on
the air, a thrust approximately
perpendicular to its plane of rotation.
It includes the control components
normally supplied by its
manufacturer.
RAMP WEIGHT—The total weight
of the aircraft while on the ramp. It
differs from takeoff weight by the
weight of the fuel that will be
consumed in taxiing to the point of
takeoff.
RATE OF TURN—The rate in
degrees/second of a turn.
RECIPROCATING ENGINE—An
engine that converts the heat energy
from burning fuel into the
reciprocating movement of the pistons.
This movement is converted into
a rotary motion by the connecting rods
and crankshaft.
REDUCTION GEAR—The gear
arrangement in an aircraft engine that
allows the engine to turn at a faster
speed than the propeller.
REGION OF REVERSE
COMMAND—Flight regime in
which flight at a higher airspeed
requires a lower power setting and a
lower airspeed requires a higher
power setting in order to maintain
altitude.
REGISTRATION
CERTIFICATE—A State and Federal
certificate that documents
aircraft ownership.
RELATIVE WIND—The direction
of the airflow with respect to the wing.
If a wing moves forward horizontally,
the relative wind moves backward
horizontally. Relative wind is parallel
to and opposite the flightpath of
the airplane.
alignment guidance during takeoff
and landings. The centerline consists
of a line of uniformly spaced stripes
and gaps.
RUNWAY EDGE LIGHTS—
Runway edge lights are used to
outline the edges of runways during
periods of darkness or restricted
visibility conditions. These light
systems are classified according to the
intensity or brightness they are
capable of producing: they are the
High Intensity Runway Lights
(HIRL), Medium Intensity Runway
Lights (MIRL), and the Low Intensity
Runway Lights (LIRL). The HIRL
and MIRL systems have variable
intensity controls, whereas the LIRLs
normally have one intensity setting.
RUNWAY END IDENTIFIER
LIGHTS (REIL)—One component
of the runway lighting system. These
lights are installed at many airfields
to provide rapid and positive
identification of the approach end of a
particular runway.
RUNWAY INCURSION—
Any occurrence at an airport
involving an aircraft, vehicle, person,
or object on the ground that creates a
collision hazard or results in loss of
separation with an aircraft taking off,
intending to takeoff, landing, or
intending to land.
RUNWAY THRESHOLD
MARKINGS—Runway threshold
markings come in two configurations.
They either consist of eight
longitudinal stripes of uniform
dimensions disposed symmetrically
about the runway centerline, or the
number of stripes is related to the
runway width. A threshold marking
helps identify the beginning of the
runway that is available for landing.
In some instances, the landing
threshold may be displaced.
SAFETY (SQUAT) SWITCH—An
electrical switch mounted on one of
the landing gear struts. It is used to
sense when the weight of the aircraft
is on the wheels.
SCAN—A procedure used by the
pilot to visually identify all resources
of information in flight.
REVERSE THRUST—A condition
where jet thrust is directed forward
during landing to increase the rate of
deceleration.
REVERSING PROPELLER—
A propeller system with a pitch
change mechanism that includes full
reversing capability. When the pilot
moves the throttle controls to reverse,
the blade angle changes to a pitch
angle and produces a reverse thrust,
which slows the airplane down during
a landing.
ROLL—The motion of the aircraft
about the longitudinal axis. It is
controlled by the ailerons.
ROUNDOUT (FLARE)—
Apitch-up during landing approach to
reduce rate of descent and forward
speed prior to touchdown.
RUDDER—The movable primary
control surface mounted on the
trailing edge of the vertical fin of an
airplane. Movement of the rudder
rotates the airplane about its vertical
axis.
RUDDERVATOR—Apair of control
surfaces on the tail of an aircraft
arranged in the form of a V. These
surfaces, when moved together by the
control wheel, serve as elevators, and
when moved differentially by the
rudder pedals, serve as a rudder.
RUNWAY CENTERLINE
LIGHTS—Runway centerline lights
are installed on some precision
approach runways to facilitate landing
under adverse visibility conditions.
They are located along the runway
centerline and are spaced at 50-foot
intervals. When viewed from the
landing threshold, the runway
centerline lights are white until the
last 3,000 feet of the runway. The
white lights begin to alternate with red
for the next 2,000 feet, and for the last
1,000 feet of the runway, all centerline
lights are red.
RUNWAY CENTERLINE
MARKINGS—
The runway centerline identifies the
center of the runway and provides
Glossary.qxd 5/7/04 10:46 AM Page G-12
G-13
SEA LEVEL—A reference height
used to determine standard
atmospheric conditions and altitude
measurements.
SEGMENTED CIRCLE—A visual
ground based structure to provide
traffic pattern information.
SERVICE CEILING—
The maximum density altitude where
the best rate-of-climb airspeed will
produce a 100 feet-per-minute climb
at maximum weight while in a clean
configuration with maximum continuous
power.
SERVO TAB—An auxiliary control
mounted on a primary control surface,
which automatically moves in the
direction opposite the primary control
to provide an aerodynamic assist in
the movement of the control.
SHAFT HORSE POWER (SHP)—
Turboshaft engines are rated in shaft
horsepower and calculated by use of
a dynamometer device. Shaft
horsepower is exhaust thrust
converted to a rotating shaft.
SHOCK WAVES—A compression
wave formed when a body moves
through the air at a speed greater than
the speed of sound.
SIDESLIP—A slip in which the
airplane’s longitudinal axis remains
parallel to the original flightpath, but the
airplane no longer flies straight ahead.
Instead, the horizontal component of
wing lift forces the airplane to move
sideways toward the low wing.
SINGLE ENGINE ABSOLUTE
CEILING—The altitude that a twinengine
airplane can no longer climb
with one engine inoperative.
SINGLE ENGINE SERVICE
CEILING—The altitude that a twinengine
airplane can no longer climb at
a rate greater then 50 f.p.m. with one
engine inoperative.
SKID—A condition where the tail of
the airplane follows a path outside the
path of the nose during a turn.
SPLIT SHAFT
TURBINE ENGINE—See FREE
POWER TURBINE ENGINE.
SPOILERS—High-drag devices that
can be raised into the air flowing over
an airfoil, reducing lift and increasing
drag. Spoilers are used for roll control
on some aircraft. Deploying spoilers
on both wings at the same time allows
the aircraft to descend without gaining
speed. Spoilers are also used to
shorten the ground roll after landing.
SPOOL—A shaft in a turbine engine
which drives one or more
compressors with the power derived
from one or more turbines.
STABILATOR—A single-piece horizontal
tail surface on an airplane that
pivots around a central hinge point. A
stabilator serves the purposes of both
the horizontal stabilizer and
the elevator.
STABILITY—The inherent quality
of an airplane to correct for conditions
that may disturb its equilibrium, and
to return or to continue on the original
flightpath. It is primarily an airplane
design characteristic.
STABILIZED APPROACH—A
landing approach in which the pilot
establishes and maintains a constant
angle glidepath towards a predetermined
point on the landing runway. It
is based on the pilot’s judgment of
certain visual cues, and depends on
the maintenance of a constant final
descent airspeed and configuration.
STALL—A rapid decrease in lift
caused by the separation of airflow
from the wing’s surface brought on by
exceeding the critical angle of attack.
A stall can occur at any pitch attitude
or airspeed.
STALL STRIPS—Aspoiler attached
to the inboard leading edge of some
wings to cause the center section of
the wing to stall before the tips. This
assures lateral control throughout the
stall.
SLIP—An intentional maneuver to
decrease airspeed or increase rate of
descent, and to compensate for a
crosswind on landing. A slip can also
be unintentional when the pilot fails
to maintain the aircraft in coordinated
flight.
SPECIFIC FUEL
CONSUMPTION—
Number of pounds of fuel consumed
in 1 hour to produce 1 HP.
SPEED—The distance traveled in a
given time.
SPEED BRAKES—A control
system that extends from the airplane
structure into the airstream to
produce drag and slow the airplane.
SPEED INSTABILITY—
A condition in the region of reverse
command where a disturbance that
causes the airspeed to decrease causes
total drag to increase, which in turn,
causes the airspeed to decrease
further.
SPEED SENSE—The ability to
sense instantly and react to any
reasonable variation of airspeed.
SPIN—An aggravated stall that
results in what is termed an “autorotation”
wherein the airplane follows a
downward corkscrew path. As the airplane
rotates around the vertical axis,
the rising wing is less stalled than the
descending wing creating a rolling,
yawing, and pitching motion.
SPIRAL INSTABILITY—
A condition that exists when the static
directional stability of the airplane is
very strong as compared to the effect
of its dihedral in maintaining lateral
equilibrium.
SPIRALING SLIPSTREAM—The
slipstream of a propeller-driven
airplane rotates around the airplane.
This slipstream strikes the left side of
the vertical fin, causing the airplane to
yaw slightly. Vertical stabilizer offset
is sometimes used by aircraft designers
to counteract this tendency.
Glossary.qxd 5/7/04 10:46 AM Page G-13
G-14
STANDARD ATMOSPHERE—
At sea level, the standard atmosphere
consists of a barometric pressure of
29.92 inches of mercury (in. Hg.) or
1013.2 millibars, and a temperature of
15°C (59°F). Pressure and temperature
normally decrease as altitude
increases. The standard lapse rate in
the lower atmosphere for each 1,000
feet of altitude is approximately 1 in.
Hg. and 2°C (3.5°F). For example, the
standard pressure and temperature at
3,000 feet mean sea level (MSL) is
26.92 in. Hg. (29.92 - 3) and 9°C
(15°C - 6°C).
STANDARD DAY—
See STANDARD ATMOSPHERE.
STANDARD EMPTY WEIGHT
(GAMA)—This weight consists of
the airframe, engines, and all items of
operating equipment that have fixed
locations and are permanently
installed in the airplane; including
fixed ballast, hydraulic fluid, unusable
fuel, and full engine oil.
STANDARD WEIGHTS—These
have been established for numerous
items involved in weight and balance
computations. These weights should
not be used if actual weights are
available.
STANDARD-RATE TURN—A turn
at the rate of 3º per second which
enables the airplane to complete a
360º turn in 2 minutes.
STARTER/GENERATOR—
A combined unit used on turbine
engines. The device acts as a starter
for rotating the engine, and after
running, internal circuits are shifted to
convert the device into a generator.
STATIC STABILITY—The initial
tendency an aircraft displays when
disturbed from a state of equilibrium.
STATION—A location in the
airplane that is identified by a number
designating its distance in inches from
the datum. The datum is, therefore,
identified as station zero. An item
located at station +50 would have an
arm of 50 inches.
TAXIWAY LIGHTS—
Omnidirectional lights that outline the
edges of the taxiway and are blue in
color.
TAXIWAY TURNOFF LIGHTS—
Flush lights which emit a steady green
color.
TETRAHEDRON—
A large, triangular-shaped, kite-like
object installed near the runway.
Tetrahedrons are mounted on a pivot
and are free to swing with the wind to
show the pilot the direction of the
wind as an aid in takeoffs and
landings.
THROTTLE—The valve in a
carburetor or fuel control unit that
determines the amount of fuel-air
mixture that is fed to the engine.
THRUST LINE—An imaginary line
passing through the center of the
propeller hub, perpendicular to the
plane of the propeller rotation.
THRUST REVERSERS—Devices
which redirect the flow of jet exhaust
to reverse the direction of thrust.
THRUST—The force which imparts
a change in the velocity of a mass.
This force is measured in pounds but
has no element of time or rate. The
term, thrust required, is generally
associated with jet engines. A forward
force which propels the airplane
through the air.
TIMING—The application of
muscular coordination at the proper
instant to make flight, and all
maneuvers incident thereto, a constant
smooth process.
TIRE CORD—Woven metal wire
laminated into the tire to provide extra
strength. A tire showing any cord
must be replaced prior to any further
flight.
TORQUE METER—An indicator
used on some large reciprocating
engines or on turboprop engines to
indicate the amount of torque the
engine is producing.
STICK PULLER—A device that
applies aft pressure on the control
column when the airplane is approaching
the maximum operating speed.
STICK PUSHER—A device that
applies an abrupt and large forward
force on the control column when the
airplane is nearing an angle of attack
where a stall could occur.
STICK SHAKER—An artificial
stall warning device that vibrates the
control column.
STRESS RISERS—
A scratch, groove, rivet hole, forging
defect or other structural discontinuity
that causes a concentration of stress.
SUBSONIC—Speed below the speed
of sound.
SUPERCHARGER—An engine- or
exhaust-driven air compressor used to
provide additional pressure to the
induction air so the engine can
produce additional power.
SUPERSONIC—Speed above the
speed of sound.
SUPPLEMENTAL TYPE
CERTIFICATE (STC)—
A certificate authorizing an alteration
to an airframe, engine, or component
that has been granted an Approved
Type Certificate.
SWEPT WING—A wing planform
in which the tips of the wing are
farther back than the wing root.
TAILWHEEL AIRCRAFT—
SEE CONVENTIONAL LANDING
GEAR.
TAKEOFF ROLL
(GROUND ROLL)—The total
distance required for an aircraft to
become airborne.
TARGET REVERSER—A thrust
reverser in a jet engine in which
clamshell doors swivel from the
stowed position at the engine tailpipe
to block all of the outflow and redirect
some component of the thrust
forward.
Glossary.qxd 5/7/04 10:46 AM Page G-14
G-15
TORQUE SENSOR—
See TORQUE METER.
TORQUE—1.Aresistance to turning
or twisting. 2. Forces that produce a
twisting or rotating motion. 3. In an
airplane, the tendency of the aircraft
to turn (roll) in the opposite direction
of rotation of the engine and propeller.
TOTAL DRAG—The sum of the
parasite and induced drag.
TOUCHDOWN ZONE LIGHTS—
Two rows of transverse light bars
disposed symmetrically about the
runway centerline in the runway
touchdown zone.
TRACK—The actual path made over
the ground in flight.
TRAILING EDGE—The portion of
the airfoil where the airflow over the
upper surface rejoins the lower
surface airflow.
TRANSITION LINER—
The portion of the combustor that
directs the gases into the turbine
plenum.
TRANSONIC—At the speed of
sound.
TRANSPONDER—The airborne
portion of the secondary surveillance
radar system. The transponder emits a
reply when queried by a radar facility.
TRICYCLE GEAR—Landing gear
employing a third wheel located on
the nose of the aircraft.
TRIM TAB—A small auxiliary
hinged portion of a movable control
surface that can be adjusted during
flight to a position resulting in a
balance of control forces.
TRIPLE SPOOL ENGINE—
Usually a turbofan engine design
where the fan is the N1 compressor,
followed by the N2 intermediate
compressor, and the N3 high pressure
compressor, all of which rotate on
separate shafts at different speeds.
TURBINE SECTION—The section
of the engine that converts high
pressure high temperature gas into
rotational energy.
TURBOCHARGER—
An air compressor driven by exhaust
gases, which increases the pressure of
the air going into the engine through
the carburetor or fuel injection
system.
TURBOFAN ENGINE—A turbojet
engine in which additional propulsive
thrust is gained by extending a portion
of the compressor or turbine blades
outside the inner engine case. The
extended blades propel bypass air
along the engine axis but between the
inner and outer casing. The air is not
combusted but does provide additional
thrust.
TURBOJET ENGINE—A jet
engine incorporating a turbine-driven
air compressor to take in and compress
air for the combustion of fuel,
the gases of combustion being used
both to rotate the turbine and create a
thrust producing jet.
TURBOPROP ENGINE—Aturbine
engine that drives a propeller through
a reduction gearing arrangement.
Most of the energy in the exhaust
gases is converted into torque, rather
than its acceleration being used to
propel the aircraft.
TURBULENCE—An occurrence in
which a flow of fluid is unsteady.
TURN COORDINATOR—A rate
gyro that senses both roll and yaw due
to the gimbal being canted. Has
largely replaced the turn-and-slip
indicator in modern aircraft.
TURN-AND-SLIP INDICATOR—
Aflight instrument consisting of a rate
gyro to indicate the rate of yaw and a
curved glass inclinometer to indicate
the relationship between gravity and
centrifugal force. The turn-and-slip
indicator indicates the relationship
between angle of bank and rate of
yaw. Also called a turn-and-bank
indicator.
TROPOPAUSE—The boundary
layer between the troposphere and the
mesosphere which acts as a lid to
confine most of the water vapor, and
the associated weather, to the
troposphere.
TROPOSPHERE—The layer of the
atmosphere extending from the
surface to a height of 20,000 to 60,000
feet depending on latitude.
TRUE AIRSPEED (TAS)—
Calibrated airspeed corrected for altitude
and nonstandard temperature.
Because air density decreases with an
increase in altitude, an airplane has to
be flown faster at higher altitudes to
cause the same pressure difference
between pitot impact pressure and
static pressure. Therefore, for a given
calibrated airspeed, true airspeed
increases as altitude increases; or for a
given true airspeed, calibrated airspeed
decreases as altitude increases.
TRUE ALTITUDE—The vertical
distance of the airplane above sea
level—the actual altitude. It is often
expressed as feet above mean sea
level (MSL). Airport, terrain, and
obstacle elevations on aeronautical
charts are true altitudes.
T-TAIL—An aircraft with the
horizontal stabilizer mounted on the
top of the vertical stabilizer, forming
a T.
TURBINE BLADES—The portion
of the turbine assembly that absorbs
the energy of the expanding gases and
converts it into rotational energy.
TURBINE OUTLET
TEMPERATURE (TOT)—
The temperature of the gases as they
exit the turbine section.
TURBINE PLENUM—The portion
of the combustor where the gases are
collected to be evenly distributed to
the turbine blades.
TURBINE ROTORS—The portion
of the turbine assembly that mounts to
the shaft and holds the turbine blades
in place.
Glossary.qxd 5/7/04 10:46 AM Page G-15
G-16
TURNING ERROR—One of the
errors inherent in a magnetic compass
caused by the dip compensating
weight. It shows up only on turns to or
from northerly headings in the
Northern Hemisphere and southerly
headings in the Southern Hemisphere.
Turning error causes the compass to
lead turns to the north or south and lag
turns away from the north or south.
ULTIMATE LOAD FACTOR—
In stress analysis, the load that causes
physical breakdown in an aircraft or
aircraft component during a strength
test, or the load that according to
computations, should cause such a
breakdown.
UNFEATHERING
ACCUMULATOR—Tanks that hold
oil under pressure which can be used
to unfeather a propeller.
UNICOM—
A nongovernment air/ground radio
communication station which may
provide airport information at public
use airports where there is no tower or
FSS.
UNUSABLE FUEL—Fuel that
cannot be consumed by the engine.
This fuel is considered part of the
empty weight of the aircraft.
USEFUL LOAD—The weight of the
pilot, copilot, passengers, baggage,
usable fuel, and drainable oil. It is the
basic empty weight subtracted from
the maximum allowable gross weight.
This term applies to general aviation
aircraft only.
UTILITY CATEGORY—
An airplane that has a seating
configuration, excluding pilot seats,
of nine or less, a maximum
certificated takeoff weight of 12,500
pounds or less, and intended for
limited acrobatic operation.
V-BARS—The flight director
displays on the attitude indicator that
provide control guidance to the pilot.
V-SPEEDS—Designated speeds for a
specific flight condition.
VFE—The maximum speed with the
flaps extended. The upper limit of the
white arc.
VFO—The maximum speed that the
flaps can be extended or retracted.
VFR TERMINAL AREA
CHARTS (1:250,000)—
Depict Class B airspace which
provides for the control or
segregation of all the aircraft within
the Class B airspace. The chart depicts
topographic information and
aeronautical information which
includes visual and radio aids
to navigation, airports, controlled
airspace, restricted areas, obstructions,
and related data.
V-G DIAGRAM—A chart that
relates velocity to load factor. It is
valid only for a specific weight,
configuration, and altitude and shows
the maximum amount of positive or
negative lift the airplane is capable of
generating at a given speed. Also
shows the safe load factor limits and
the load factor that the aircraft can
sustain at various speeds.
VISUAL APPROACH SLOPE
INDICATOR (VASI)—
The most common visual glidepath
system in use. The VASI provides
obstruction clearance within 10° of
the extended runway centerline, and
to 4 nautical miles (NM) from the
runway threshold.
VISUAL FLIGHT
RULES (VFR)—
Code of Federal Regulations that govern
the procedures for conducting
flight under visual conditions.
VLE—Landing gear extended speed.
The maximum speed at which an
airplane can be safely flown with the
landing gear extended.
VLOF—Lift-off speed. The speed at
which the aircraft departs the runway
during takeoff.
VLO—Landing gear operating speed.
The maximum speed for extending or
retracting the landing gear if using an
airplane equipped with retractable
landing gear.
VAPOR LOCK—A condition in
which air enters the fuel system and it
may be difficult, or impossible, to
restart the engine. Vapor lock may
occur as a result of running a fuel tank
completely dry, allowing air to enter
the fuel system. On fuel-injected
engines, the fuel may become so hot it
vaporizes in the fuel line, not allowing
fuel to reach the cylinders.
VA—The design maneuvering speed.
This is the “rough air” speed and the
maximum speed for abrupt
maneuvers. If during flight, rough air
or severe turbulence is encountered,
reduce the airspeed to maneuvering
speed or less to minimize stress on the
airplane structure. It is important to
consider weight when referencing this
speed. For example, VA may be 100
knots when an airplane is heavily
loaded, but only 90 knots when the
load is light.
VECTOR—A force vector is a
graphic representation of a force and
shows both the magnitude and
direction of the force.
VELOCITY—The speed or rate of
movement in a certain direction.
VERTICAL AXIS—An imaginary
line passing vertically through the
center of gravity of an aircraft. The
vertical axis is called the z-axis or the
yaw axis.
VERTICAL CARD COMPASS—
Amagnetic compass that consists of
an azimuth on a vertical card,
resembling a heading indicator with a
fixed miniature airplane to accurately
present the heading of the aircraft.
The design uses eddy current
damping to minimize lead and lag
during turns.
VERTICAL
SPEED INDICATOR (VSI)—
An instrument that uses static pressure
to display a rate of climb or descent in
feet per minute. The VSI can also
sometimes be called a vertical
velocity indicator (VVI).
VERTICAL STABILITY—Stability
about an aircraft’s vertical axis. Also
called yawing or directional stability.
Glossary.qxd 5/7/04 10:46 AM Page G-16
G-17
VMC—Minimum control airspeed.
This is the minimum flight speed at
which a twin-engine airplane can be
satisfactorily controlled when an
engine suddenly becomes inoperative
and the remaining engine is at takeoff
power.
VMD—Minimum drag speed.
VMO—Maximum operating speed
expressed in knots.
VNE—Never-exceed speed. Operating
above this speed is prohibited since it
may result in damage or structural
failure. The red line on the airspeed
indicator.
VNO—Maximum structural cruising
speed. Do not exceed this speed
except in smooth air. The upper limit
of the green arc.
VP—Minimum dynamic hydroplaning
speed. The minimum speed
required to start dynamic
hydroplaning.
VR—Rotation speed. The speed that
the pilot begins rotating the aircraft
prior to lift-off.
VS0—Stalling speed or the minimum
steady flight speed in the landing configuration.
In small airplanes, this is
the power-off stall speed at the maximum
landing weight in the landing
configuration (gear and flaps down).
The lower limit of the white arc.
VS1—Stalling speed or the minimum
steady flight speed obtained in a
specified configuration. For most
airplanes, this is the power-off stall
speed at the maximum takeoff weight
in the clean configuration (gear up, if
retractable, and flaps up). The lower
limit of the green arc.
VSSE—Safe, intentional one-engine
inoperative speed. The minimum
speed to intentionally render the
critical engine inoperative.
V-TAIL—A design which utilizes
two slanted tail surfaces to perform
equal to the mass of the body times
the local value of gravitational
acceleration. One of the four main
forces acting on an aircraft.
Equivalent to the actual weight of the
aircraft. It acts downward through the
aircraft’s center of gravity toward the
center of the Earth. Weight opposes
lift.
WEIGHT AND BALANCE—The
aircraft is said to be in weight and
balance when the gross weight of the
aircraft is under the max gross weight,
and the center of gravity is within
limits and will remain in limits for the
duration of the flight.
WHEELBARROWING—
A condition caused when forward
yoke or stick pressure during takeoff
or landing causes the aircraft to ride
on the nosewheel alone.
WIND CORRECTION ANGLE—
Correction applied to the course to
establish a heading so that track will
coincide with course.
WIND
DIRECTION INDICATORS—
Indicators that include a wind sock,
wind tee, or tetrahedron. Visual
reference will determine wind
direction and runway in use.
WIND SHEAR—A sudden, drastic
shift in windspeed, direction, or both
that may occur in the horizontal or
vertical plane.
WINDMILLING—When the air
moving through a propeller creates
the rotational energy.
WINDSOCK—A truncated cloth
cone open at both ends and mounted
on a freewheeling pivot that indicates
the direction from which the wind is
blowing.
WING—Airfoil attached to each side
of the fuselage and are the main
lifting surfaces that support the
airplane in flight.
the same functions as the surfaces of a
conventional elevator and rudder
configuration. The fixed surfaces act
as both horizontal and vertical
stabilizers.
VX—Best angle-of-climb speed. The
airspeed at which an airplane gains the
greatest amount of altitude in a given
distance. It is used during a short-field
takeoff to clear an obstacle.
VXSE—Best angle of climb speed with
one engine inoperative. The airspeed
at which an airplane gains the greatest
amount of altitude in a given distance
in a light, twin-engine airplane
following an engine failure.
VY—Best rate-of-climb speed. This
airspeed provides the most altitude
gain in a given period of time.
VYSE—Best rate-of-climb speed with
one engine inoperative. This airspeed
provides the most altitude gain in a
given period of time in a light, twinengine
airplane following an engine
failure.
WAKE TURBULENCE—Wingtip
vortices that are created when an
airplane generates lift. When an
airplane generates lift, air spills over
the wingtips from the high pressure
areas below the wings to the low
pressure areas above them. This flow
causes rapidly rotating whirlpools of
air called wingtip vortices or wake
turbulence.
WASTE GATE—A controllable
valve in the tailpipe of an aircraft
reciprocating engine equipped with a
turbocharger. The valve is controlled
to vary the amount of exhaust gases
forced through the turbocharger
turbine.
WEATHERVANE—The tendency of
the aircraft to turn into the relative
wind.
WEIGHT—A measure of the
heaviness of an object. The force by
which a body is attracted toward the
center of the Earth (or another
celestial body) by gravity. Weight is
Glossary.qxd 5/7/04 10:46 AM Page G-17
G-18
WING AREA—The total surface of
the wing (square feet), which includes
control surfaces and may include
wing area covered by the fuselage
(main body of the airplane), and
engine nacelles.
WING SPAN—
The maximum distance from wingtip
to wingtip.
WINGTIP VORTICES—
The rapidly rotating air that spills over
an airplane’s wings during flight. The
intensity of the turbulence depends on
the airplane’s weight, speed, and
configuration. It is also referred to as
ZERO FUEL WEIGHT—
The weight of the aircraft to include
all useful load except fuel.
ZERO SIDESLIP—Amaneuver in a
twin-engine airplane with one engine
inoperative that involves a small
amount of bank and slightly
uncoordinated flight to align the
fuselage with the direction of travel
and minimize drag.
ZERO THRUST
(SIMULATED FEATHER)—
An engine configuration with a low
power setting that simulates a
propeller feathered condition.
wake turbulence. Vortices from heavy
aircraft may be extremely hazardous
to small aircraft.
WING TWIST—A design feature
incorporated into some wings to
improve aileron control effectiveness
at high angles of attack during an
approach to a stall.
YAW—Rotation about the vertical
axis of an aircraft.
YAW STRING—Astring on the nose
or windshield of an aircraft in view of
the pilot that indicates any slipping or
skidding of the aircraft.
Glossary.qxd 5/7/04 10:46 AM Page G-18
I-1
180° POWER-OFF APPROACH 8-23
360° POWER-OFF APPROACH 8-24
90° POWER-OFF APPROACH 8-21
A
ABSOLUTE CEILING 12-8
ACCELERATED STALL 4-9
ACCELERATE-GO DISTANCE 12-8
ACCELERATE-STOP DISTANCE 12-8
ACCURACYAPPROACH 8-21
180° power-off 8-23
360° power-off 8-24
90° power-off 8-21
ADVERSE YAW3-8
AFTER LANDING 2-11
crosswind tailwheel 13-5
roll 8-7
tailwheel 13-4
AIMING POINT 8-8
AIRCRAFT LOGBOOKS 2-1
AIRFOIL TYPES 11-1
AIRMANSHIP 1-1
skills 1-1
AIRPLANE EQUIPMENT, Night 10-3
AIRPLANE FEEL 3-2
AIRPLANE LIGHTING, Night 10-3
AIRPORT LIGHTING 10-4
AIRPORT TRAFFIC PATTERN 7-1
base leg 7-3
crosswind leg 7-4
departure leg 7-4
downwind leg 7-3
entry leg 7-3
final approach leg 7-3
upwind leg 7-3
AIRWORTHINESS DIRECTIVES 2-1
ALTERNATOR/GENERATOR 12-7
ALTITUDE TURBOCHARGING 11-7
ANTI-ICING 12-7
APPROACH AND LANDING 8-1
after-landing roll 8-7
base leg 8-1
crosswind 8-15
emergency 8-25
estimating height and movement 8-4
faulty 8-27
final approach 8-2
go-around 8-11
multiengine 12-14
night 10-6
normal 8-1
roundout (flare) 8-5
short-field 8-17
soft-field 8-19
stabilized approach 8-7
touchdown 8-6
turbulent air 8-17
use of flaps 8-3
ATTITUDE FLYING 3-2
AUTOPILOT 12-6
AXIAL FLOW 14-5
B
BACK SIDE OF THE POWER CURVE 8-19
BALLOONING 8-3, 8-30
BANK ATTITUDE 3-2
BASE LEG 7-3, 8-1
BEFORE TAKEOFF CHECK 2-11
BEST ANGLE OF CLIMB (VX) 3-13, 12-1
one engine inoperative (VXSE) 12-1
BEST GLIDE SPEED 3-16
BEST RATE OF CLIMB 3-13, 12-1
one engine inoperative (VYSE) 12-1
BETA RANGE 14-7
BLACK HOLE APPROACH 10-2
BOUNCING 8-30
BUS BAR 14-8
BUS TIE 14-9
BYPASS AIR 15-2
BYPASS RATIO 15-2
C
CASCADE REVERSER 15-14
CENTRIFUGAL COMPRESSOR
STAGE 14-5
CHANDELLE 9-4
CHECKLISTS, Use of, 1-6
CIRCUIT BREAKER 14-9
CLEAR OF RUNWAY 2-11
CLIMB GRADIENT 12-8
Index.qxd 5/7/04 10:52 AM Page I-1
I-2
CLIMBS 3-13
maximum performance 5-8
night 10-5
COCKPIT MANAGEMENT 2-7
COLLISION AVOIDANCE 1-4
COMBUSTION CHAMBER 14-1
COMBUSTION HEATER 12-6
COMPLEX AIRPLANE 11-1
COMPRESSION RATIO 15-1
COMPRESSOR 14-1
CONDITION LEVER 14-4
CONES 10-1
CONFINED AREA 16-4
CONSTANT-SPEED PROPELLER 11-4
blade angle control 11-5
governing range 11-5
operation 11-5
CONTROLLABLE-PITCH PROPELLER 11-3
CONVENTIONAL GEAR AIRPLANE 13-1
CORE AIRFLOW 15-2
CRAZING 2-2
CRITICALALTITUDE 11-7
CRITICAL MACH 15-7
CROSS-CONTROL STALL 4-10
CROSSWIND APPROACH
AND LANDING 8-13
CROSSWIND COMPONENT 5-6
CROSSWIND LEG 7-4
CROSSWIND TAKEOFF 5-5
CURRENT LIMITER 14-9
D
DEICING 12-7
DEPARTURE LEG 7-4
DESCENTS 3-15
minimum safe airspeed 3-16
partial power 3-16
DITCHING 16-1
DOWNWASH 8-3
DOWNWIND LEG 7-3
DRAG DEVICES 15-13
DRIFT 6-2
DUCTED FAN 15-2
E
EGT 11-8
EIGHTS ACROSS A ROAD 6-11
EIGHTS ALONG A ROAD 6-9
EIGHTS AROUND PYLONS 6-11
EIGHTS-ON-PYLONS 6-12
ELEMENTARY EIGHTS 6-9
ELEVATOR TRIM STALL 4-11
ELT 2-1
EMERGENCIES
abnormal instrument indications 16-11
door open in flight 16-12
electrical system 16-10
engine failure 16-5
fires 16-7
flap failure 16-8
landing gear malfunction 16-9
loss of elevator control 16-9
night 10-8
pitot-static system 16-11
VFR flight into IMC 16-12
EMERGENCYAPPROACH
AND LANDING 8-25
EMERGENCY DESCENTS 16-6
EMERGENCY GEAR
EXTENSION SYSTEM 11-10
EMERGENCY LANDINGS 16-1
airplane configuration 16-3
psychological hazards 16-1
safety concepts 16-2
terrain selection 16-3
terrain types 16-4
EMERGENCY LOCATOR
TRANSMITTER 2-1
ENGINE FAILURE AFTER TAKEOFF 16-5
ENGINE FAILURE, MULTIENGINE
approach and landing 12-22
during flight 12-21
flight principles 12-23
takeoff 12-18
ENGINE SHUTDOWN 2-12
ENGINE STARTING 2-7
ENTRY LEG 7-3
EXHAUST GAS TEMPERATURE 11-8
EXHAUST MANIFOLD 11-7
EXHAUST SECTION 14-1
F
FALSE START 14-10
FAULTYAPPROACHES 8-27
ballooning 8-30
floating 8-29
high final 8-27
high roundout 8-28
low final 8-27
slow final 8-28
FEATHERING 12-3
FEDERALAVIATION ADMINISTRATION (FAA) 1-1
FEEL OF THE AIRPLANE 3-2
FINAL APPROACH 8-2
FINAL APPROACH LEG 7-3
FIRES
cabin 16-8
electrical 16-7
engine 16-7
Index.qxd 5/7/04 10:52 AM Page I-2
I-3
FIXED SHAFT ENGINE 14-3
FLAP EXTENSION SPEED (VFE) 12-15
FLAPS 11-1
effectiveness 11-2
function 11-1
operational procedures 11-2
use of 8-3
FLARE 8-5
FLIGHT CONTROLS 3-1
FLIGHT DIRECTOR 12-6
FLIGHT IDLE 14-7
FLIGHT INSTRUCTOR, ROLE OF 1-3
FLIGHT SAFETY 1-4
FLIGHT STANDARDS DISTRICT
OFFICE (FSDO) 1-2
FLIGHT TRAINING SCHOOLS 1-3
FLOATING 8-29
FORCED LANDING 16-1
FORWARD SLIP 8-10
FOUR FUNDAMENTALS 3-1
FREE TURBINE ENGINE 14-5
FUEL CONTROL UNIT 14-6
FUEL CONTROLLER 14-1
FUEL CROSSFEED 12-5
FUEL HEATER 15-3
G
GAS GENERATOR 15-2
GAS TURBINE ENGINE 14-1
GLIDE 3-16
GLIDE RATIO 3-16
GO-AROUND (REJECTED LANDING) 8-11, 12-17
GOVERNING RANGE 11-5
GROUND BOOSTING 11-7
GROUND EFFECT 5-7, 8-13
GROUND INSPECTION 2-1
GROUND LOOP 8-33, 13-6
GROUND OPERATIONS 2-7
GROUND REFERENCE MANEUVERS 6-1
drift and ground track control 6-2
eights across a road 6-11
eights along a road 6-9
eights around pylons 6-11
eights-on-pylons (pylon eights) 6-12
rectangular course 6-4
s-turns across a road 6-6
turns around a point 6-7
GROUND ROLL 5-1
GROUND TRACK CONTROL 6-2
GROUNDSPEED 6-3
HAND PROPPING 2-8
HAND SIGNALS 2-7
HIGH PERFORMANCE AIRPLANE 11-1
HOT START 14-10
HUNG START 14-10
HYDROPLANING 8-34
I
ILLUSIONS 10-2
INITIAL CLIMB 5-1
INTAKE MANIFOLD 11-7
INTEGRATED FLIGHT INSTRUCTION 3-3
INTENTIONAL SPIN 4-15
INVERTER 14-8
JET AIRPLANE 15-1
approach and landing 15-19
low speed flight 15-10
pilot sensations 15-15
rotation and lift-off 15-18
stalls 15-10
takeoff and climb 15-16
touchdown and rollout 15-24
J
JET ENGINE 15-1
efficiency 15-5
fuel heater 15-3
ignition 15-3
operating 15-2
K
KINESTHESIA 3-2
L
L/DMAX 3-16
LANDING GEAR
controls 11-10
electrical 11-9
electrohydraulic 11-9
emergency extension 11-10
hydraulic 11-9
malfunction 16-9
operational procedures 11-12
position indicators 11-10
retractable 11-9
safety devices 11-10
tailwheel 13-1
LATERALAXIS 3-2
LAZY EIGHT 9-6
LEVEL FLIGHT 3-4
LIFT-OFF 5-1
LIFT-OFF SPEED (VLOF) 12-1
Index.qxd 5/7/04 10:52 AM Page I-3
I-4
LONGITUDINAL AXIS 3-2
LOSS OF DIRECTIONAL
CONTROL DEMONSTRATION 12-27
M
MACH 15-7
MACH BUFFET BOUNDARIES 15-8
MACH TUCK 15-7
MANEUVERING SPEED 9-1
MAXIMUM OPERATING SPEED 15-6
MAXIMUM PERFORMANCE
CLIMB 5-8
MAXIMUM SAFE
CROSSWIND VELOCITIES 8-16
MINIMUM CONTROL SPEED (VMC) 12-2
MINIMUM CONTROLLABLE
AIRSPEED 4-1
MINIMUM DRAG SPEED 4-2
MULTIENGINE AIRPLANE 12-1
approach and landing 12-14
crosswind approach and landing 12-16
engine failure during flight 12-21
engine failure on takeoff 12-18
fuel crossfeed 12-5
go-around 12-17
ground operation 12-12
level off and cruise 12-14
one engine inoperative approach and
landing 12-22
propeller 12-3
propeller synchronization 12-5
rejected takeoff 12-18
short-field operations 12-16
slow flight 12-25
stalls 12-25
takeoff and climb 12-12
weight and balance 12-10
MUSHING 3-2
N
NIGHT OPERATIONS
airplane equipment 10-3
airplane lighting 10-3
airport and navigation lighting aids 10-4
approach and landing 10-6
emergencies 10-8
illusions 10-2
orientation and navigation 10-6
pilot equipment 10-3
preparation and preflight 10-4
start, taxi, and runup 10-5
takeoff and climb 10-5
NIGHT VISION 10-1
NOISE ABATEMENT 5-11
NORMAL TAKEOFF 5-2
NOSE BAGGAGE COMPARTMENT 12-7
O
ONE-ENGINE-INOPERATIVE SPEED (VSSE) 12-1
OVERBANKING TENDENCY 3-9
OVERBOOST CONDITION 11-9
OVERSPEED 15-8
P
PARALLAX ERROR 3-11
PARKING 2-11
PILOT EQUIPMENT, Night 10-3
PILOT EXAMINER, Role of 1-2
PITCH AND POWER 3-19
PITCH ATTITUDE 3-2
PIVOTALALTITUDE 6-14
PORPOISING 8-31
POSITION LIGHTS 10-3
POSITIVE TRANSFER OF CONTROLS 1-6
POSTFLIGHT 2-12
POWER CURVE 8-19
POWER LEVER 14-4
PRACTICAL SLIP LIMIT 8-11
PRACTICAL TEST STANDARDS (PTS) 1-4
PRECAUTIONARY LANDING 16-1
PREFLIGHT INSPECTION 2-2
PRESSURE CONTROLLER 11-7
PROPELLER 11-3, 12-3
PROPELLER BLADE ANGLE 11-4
control 11-5
PROPELLER CONTROL 11-4
PROPELLER SYNCHRONIZATION 12-5
PSYCHOLOGICAL HAZARDS 16-1
PYLON EIGHTS 6-12
R
RADIUS OF TURN 3-10
RECTANGULAR COURSE 6-4
REGION OF REVERSE COMMAND 8-19
REJECTED LANDING 8-11
REJECTED TAKEOFF 5-11, 12-18
RETRACTABLE LANDING GEAR 11-9
approach and landing 11-13
controls 11-10
electrical 11-9
electrohydraulic 11-9
emergency extension 11-10
hydraulic 11-9
Index.qxd 5/7/04 10:52 AM Page I-4
I-5
operational procedures 11-12
position indicators 11-10
safety devices 11-10
takeoff and climb 11-13
transition training 11-14
REVERSE THRUST 14-7
RODS 10-1
ROTATING BEACON 10-4
ROTATION 5-1
ROTATION SPEED (VR) 12-1
ROUGH-FIELD TAKEOFF 5-10
ROUNDOUT 8-5
ballooning 8-3
floating 8-29
high 8-28
late or rapid 8-29
RUNWAY INCURSION 1-5
RUNWAY LIGHTS 10-4
S
SAFETY CONCEPTS 16-2
SECONDARY STALL 4-9
SECURING 2-12
SEGMENTED CIRCLE 7-3
SERVICE CEILING 12-8
SERVICING 2-12
SHORT-FIELD
approach and landing 8-17
tailwheel 13-3
takeoff 5-8
SIDESLIP 5-6, 8-10
SINK RATE 16-3
SKID 3-8
SLIP 3-8, 8-10
SLOW FLIGHT 4-1, 12-25
SOFT FIELD
approach and landing 8-19
tailwheel 13-4
takeoff 5-10
SPEED BRAKE 15-13
SPEED INSTABILITY 4-2
SPIN AWARENESS 12-26
SPINS 4-12
developed phase 4-14
entry phase 4-13
incipient phase 4-13
intentional 4-15
procedures 4-13
recovery phase 4-14
weight and balance requirements 4-16
SPLIT SHAFT ENGINE 14-5
SPOILERS 15-13
SQUAT SWITCH 11-10
STABILIZED APPROACH 8-7, 15-21
STALLAWARENESS 1-6
STALLS 4-3
accelerated 4-9
characteristics 4-6
cross-control 4-10
elevator trim 4-11
imminent 4-6
jet airplane 15-10
multiengine 12-25
power-off 4-7
power-on 4-8
recognition 4-3
recovery 4-4
secondary 4-9
use of ailerons/rudders 4-5
STEEP SPIRAL 9-3
STEEP TURNS 9-1
STRAIGHT FLIGHT 3-5
STRAIGHT-AND-LEVEL FLIGHT 3-4
S-TURNS ACROSS A ROAD 6-6
T
TAILWHEELAIRPLANES 13-1
crosswind landing 13-5
crosswind takeoff 13-3
short-field landing 13-6
short-field takeoff 13-3
soft-field landing 13-6
soft-field takeoff 13-4
takeoff 13-3
takeoff roll 13-2
taxiing 13-1
touchdown 13-4
wheel landing 13-6
TAKEOFF
crosswind 5-5
ground effect 5-7
multiengine 12-2
night 10-5
normal 5-2
rejected 5-11
roll 5-1
short field 5-8
soft/rough field 5-10
tailwheel 13-3
tailwheel crosswind 13-3
tailwheel short-field 13-3
tailwheel soft-field 13-4
TARGET REVERSER 15-14
TAXIING 2-9
tailwheel 13-1
THRUST LEVER 15-4
THRUST REVERSERS 15-14
TOUCHDOWN 8-6
bounce 8-30
crab 8-32
drift 8-32
Index.qxd 5/7/04 10:52 AM Page I-5
I-6
ground loop 8-33
hard landing 8-32
porpoise 8-31
tailwheel 13-4
wheelbarrowing 8-32
wing rise 8-33
TRACK 6-2
TRAFFIC PATTERN INDICATOR 7-3
TRANSITION TRAINING
complex airplane 11-14
high performance airplane 11-14
jet powered airplanes 15-1
multiengine airplane 12-31
tailwheel airplanes 13-1
turbopropeller powered airplanes 14-12
TRANSONIC FLOW 15-7
TRIM CONTROL 3-6
TURBINE INLET TEMPERATURE 11-8
TURBINE SECTION 14-1
TURBOCHARGER 11-7
failure 11-9
heat management 11-8
operating characteristics 11-8
TURBOFAN ENGINE 15-2
TURBOPROPAIRPLANE 14-1
electrical system 14-8
operational considerations 14-10
TURBOPROP ENGINES 14-2
TURBULENT AIR APPROACH
AND LANDING 8-17
TURNS 3-7
climbing 3-15
coordinated 3-9
gliding 3-18
level 3-7
medium 3-7
shallow 3-7
steep 3-8
TURNS AROUND A POINT 6-7
U
UPWIND LEG 7-3
V
VFR FLIGHT INTO
IMC CONDITIONS 16-12
VISUAL GROUND INSPECTION 2-1
V-SPEEDS 12-1, 15-16, 15-19
W
WASTE GATE 11-7
WEATHERVANE 5-5
WEIGHT AND BALANCE 12-10
WHEEL LANDING 13-6
WHEELBARROWING 5-9, 8-17, 8-32
WINDSOCK 7-3
WINGTIPWASHOUT 4-5
Y
YAW 3-2
YAW DAMPER 12-6
Index.qxd 5/7/04 10:52 AM Page I-6 |
|
IP卡
狗仔卡
发表于 2008-12-9 15:05:18
分享
收藏
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡