A320起落架正常操作

航空

游客，如果您要查看本帖隐藏内容请回复

diguo

恩。好东西。好好学习一下。

weiwei2005

好资料 多谢

gordon525

谢谢辛苦了 收藏一下

tissle

好资料，学习了。。。

bocome

起落架正常操作

航空

LANDING GEAR MENU Normal Operation 1/83
LANDING GEAR MENU Normal Operation 2/83
LANDING GEAR MENU
Normal Operation 3/83
Let’s assume that the chocks are in place in order to verify the
brakes and brake accumulator pressure.
The accumulator brake pressure is checked before setting the
brakes.
The pressure indication should be in the green area. This
indicates that the accumulator can hold the parking brake
pressure for 12 hours.
If the pressure indication is not in the green arc, use the yellow
hydraulic electrical pump to recharge the brake accumulator.
LANDING GEAR MENU
Normal Operation 4/83
We continue the test by pressing on the top of the rudder pedals to
apply maximum brake pressure.
We will check that the two needles indicate about 2600 PSI. This
check verifies that the brakes work correctly from the accumulator.
IInniittiiaattee tthhee tteesstt..
LANDING GEAR MENU Normal Operation 5/83
Noo,, ttoo iinniittiiaattee tthhee tteesstt,, pprreessss oonn tthhee ttoopp ooff tthhee rruuddddeerr ppeeddaallss..
LANDING GEAR MENU Normal Operation 6/83
Noo,, ttoo iinniittiiaattee tthhee tteesstt,, pprreessss oonn tthhee ttoopp ooff tthhee rruuddddeerr ppeeddaallss..
LANDING GEAR MENU
Normal Operation 7/83
The pressure builds up symmetrically on the left and right sides
and reaches about 2600 PSI with full pedal deflection.
LANDING GEAR MENU
Normal Operation 8/83
As we will be checking the brake wear indicators during the
walk around, we must set the PARK BRK ON.
Seett tthhee PARK BRK ttoo ON..
LANDING GEAR MENU Normal Operation 9/83
No, to set the PARK BRK, lift and turn the PARK BRK
handle.
LANDING GEAR MENU Normal Operation 10/83
No, to set the PARK BRK, lift and turn the PARK BRK
handle.
LANDING GEAR MENU Normal Operation 11/83
On the E/WD memo section PARK BRK in green
indicates that the PARK BRK handle is in the ON
position.
LANDING GEAR MENU Normal Operation 12/83
Notice that the pressure to the main brakes is indicated
for each main landing gear. This is yellow hydraulic
pressure. The PARK BRK uses the alternate braking
system which is powered by yellow hydraulic pressure.
LANDING GEAR MENU
Normal Operation 13/83
On the nose wheel we check the following:
- the gear structure and download springs
- the hydraulic lines
- the electrical wires
- the chocks, wheels and tires.
LANDING GEAR MENU Normal Operation 14/83
On the main gear we check the following:
- the gear structure and download springs
- the wheel well for general condition
- the chocks, wheels and tires
- the hydraulic lines
- the electrical wires.
LANDING GEAR MENU Normal Operation 15/83
LANDING GEAR MENU Normal Operation 16/83
The brake wear indicators indicate the state of the
carbon disks.
Note: as previously mentioned, the parking brake must
be on for an accurate brake wear check.
LANDING GEAR MENU
Normal Operation 17/83
We are back in the cockpit for the cockpit
preparation.
We verify that the three gear pins and covers are on
board and stowed. We also check that the Gravity Gear
Extension lever is stowed.
LANDING GEAR MENU
Normal Operation 18/83
It’s now time to pushback, we have to release the
PARK BRK .
Seett tthhee PARK BRK ttoo OFFFF..
LANDING GEAR MENU Normal Operation 19/83
No, to set the PARK BRK OFF, click on the
PARK BRK handle.
LANDING GEAR MENU Normal Operation 20/83
No, to set the PARK BRK OFF, click on the
PARK BRK handle.
LANDING GEAR MENU
Normal Operation 21/83
The PARK BRK is OFF. The BRAKES pressure is
back to zero.
LANDING GEAR MENU
Normal Operation 22/83
During pushback, the nose wheel steering
selector, located on the nose wheel, is in the towing
position, NW STRG DISC memo is displayed in green
on the E/WD. With this indication, nose wheel
steering is not possible from the cockpit.
LANDING GEAR MENU
Normal Operation 23/83
IItt bbeeccoomeess aambbeerr iiff oonnee eennggiinnee iiss rruunnnniinngg..
LANDING GEAR MENU
Normal Operation 24/83
The push back is completed.
Both engines are running and we will check the brakes in order to
verify that green pressure has taken over and that yellow pressure is
at zero on the brake pressure triple indicator.
To initiate the test, we first press the top of the rudder pedals and
we remove the PARKING BRK.
Reemoovvee tthhee PARKIING BRK..
LANDING GEAR MENU Normal Operation 25/83
Noo,, ttoo rreemoovvee tthhee PARKIING BRK,, cclliicckk oonn tthhee PARKIING BRK hhaannddllee..
LANDING GEAR MENU Normal Operation 26/83
Noo,, ttoo rreemoovvee tthhee PARKIING BRK,, cclliicckk oonn tthhee PARKIING BRK hhaannddllee..
LANDING GEAR MENU
Normal Operation 27/83
On the brake pressure triple indicator, the brake pressure is at zero
indicating that the Normal Braking system is in use.
Note: if brake pedals are quickly depressed a brief brake pressure
indication appears on the brake pressure triple indicator.
LANDING GEAR MENU Normal Operation 28/83
LANDING GEAR MENU Normal Operation 29/83
LANDING GEAR MENU Normal Operation 30/83
LANDING GEAR MENU
Normal Operation 31/83
LLEFFTT LLANDIING GEAR RIIGHTT LLANDIING GEAR
Notice the two green triangles for each gear. They indicate that the
gear is down and locked. There are two triangles because there are
two computers which provide the information for these indications.
These computers, called Landing Gear Control and Interface Unit
(LGCIU 1 and 2) will be discussed in the abnormal module.
NOSEWHEELL LLANDIING GEAR
LANDING GEAR MENU
Normal Operation 32/83
NOSE WHEEL LANDING
GEAR DOOR
RIGHT LANDING
GEAR DOOR
The green horizontal lines indicate that the doors are closed, in the
normal position.
LEFT LANDING
GEAR DOOR
LANDING GEAR MENU Normal Operation 33/83
LEFT MAIN
LANDING GEAR
RIGHT MAIN
LANDING GEAR
LANDING GEAR MENU
Normal Operation 34/83
Let’s have a look at the information displayed
below.
Brake temperature is displayed in green to indicate
that it is normal.
BRAKE
TEMPERATURE
LANDING GEAR MENU
Normal Operation 35/83
During taxi, the AUTO BRK is armed at MAX for
take off.
Seett tthhee AUTTO BRK ttooMAX..
LANDING GEAR MENU Normal Operation 36/83
Noo,, ttoo sseett tthhee AUTTO BRK ttooMAX,, ppuusshh tthheeMAX ppbb ssw..
LANDING GEAR MENU Normal Operation 37/83
Noo,, ttoo sseett tthhee AUTTO BRK ttooMAX,, ppuusshh tthheeMAX ppbb ssw..
LANDING GEAR MENU Normal Operation 38/83
LANDING GEAR MENU Normal Operation 39/83
LANDING GEAR MENU
Normal Operation 40/83
The following indications show that the AUTO
BRK is armed:
- ON in the selected pb,
- A message in green on the ECAM wheel page
- and AUTO BRK MAX changes from blue to green
on the take off configuration message.
LANDING GEAR MENU
Normal Operation 41/83
During taxi, either steering handwheel can be used to
control the direction of the aircraft.
The steering handwheel provides 75 degrees of nose
wheel deflection left or right. Signals from each handwheel
are summed up: if two handwheels are moved in the same
direction the nose wheel deflection will be equivalent to the
sum of the handwheel commands.
LANDING GEAR MENU Normal Operation 42/83
LANDING GEAR MENU
Normal Operation 43/83
While you are taxiing the aircraft for take off, you will check
the flight controls.
To check the rudder, you must press the rudder pedal
disconnect switch.
This button disconnects the nose wheel steering from the
rudder so that you can check full deflection of the rudder
pedals versus the indications on the ECAM.
You will see and do this in the normal operation module of
the flight controls.
LANDING GEAR MENU
Normal Operation 44/83
During take off, the aircraft direction is controlled exclusively
using the rudder pedals.
The rudder pedals provide up to 6 degrees of right and left
deflection at low speed.
As the speed increases, this deflection angle decreases
progressively until 130 kt, when directional control is 0 percent
nosewheel and 100 percent rudder.
LANDING GEAR MENU Normal Operation 45/83
LANDING GEAR MENU Normal Operation 46/83
LANDING GEAR Normal Operation 47/83
AUDIO ONLY
Normally the ECAM engine page is displayed at
this time but, so that you can see and learn the
indication of the landing gear system, we have
displayed the ECAM wheel page.
Reettrraacctt tthhee llaannddiinngg ggeeaarr..
MENU
LANDING GEAR MENU Normal Operation 48/83
No, to retract the landing gear, click on the
landing gear lever .
LANDING GEAR MENU Normal Operation 49/83
No, to retract the landing gear, click on the
landing gear lever .
LANDING GEAR MENU Normal Operation 50/83
LANDING GEAR Normal Operation 51/83
Once the landing gear lever is in the up position the
AUTO BRK is automatically disengaged:
- ON disappears on the MAX pb
- and AUTO BRK MAX disappears on the ECAM
WHEEL page.
MENU
LANDING GEAR Normal Operation 52/83
As soon as the landing gear lever is moved to the
up position, the message L/G CTL appears. This
indicates that there is a discrepancy between the
landing gear and lever position.
Watch the ECAM and the landing gear lights. We
will point out the changes as they occur.
MENU
LANDING GEAR Normal Operation 53/83
The landing gear doors deflect downward and
change to amber to indicate that they are open.
At the same time, on the main gear, the braking
system automatically brakes the wheels. As the doors
close, you will hear in the cockpit the sound of the
brake band braking the nose wheels.
MENU
LANDING GEAR Normal Operation 54/83
Then the landing gear retracts. There are two sets
of indications which inform the pilot that the landing
gear is no longer locked:
- red unlock is illuminated in the position indicator
lights
- and the landing gear indicators become red on the
ECAM wheel page.
MENU
LANDING GEAR Normal Operation 55/83
On the ECAM wheel page the gear is retracted and
the doors close.
On the landing gear panel, the unlocked indications
extinguish.
MENU
LANDING GEAR MENU Normal Operation 56/83
LANDING GEAR MENU Normal Operation 57/83
LANDING GEAR MENU
Normal Operation 58/83
It is now time to extend the landing gear. Watch the
indications.
Exxtteenndd tthhee llaannddiinngg ggeeaarr ..
LANDING GEAR MENU Normal Operation 59/83
No, to extend the landing gear, click on the landing
gear lever
LANDING GEAR MENU Normal Operation 60/83
No, to extend the landing gear, click on the landing
gear lever
LANDING GEAR Normal Operation 61/83
As soon as the handle is down, the ECAM WHEEL
page is automatically displayed.
MENU
LANDING GEAR Normal Operation 62/83
On the ECAM wheel page the landing gear door
indications change from green to amber as the doors
open.
On the landing gear panel the unlocked indications
turn red to indicate that the gear is unlocked.
MENU
LANDING GEAR Normal Operation 63/83
The landing gear unlocks and descends.
On the ECAM wheel page the landing gear
indications are displayed in red .
MENU
LANDING GEAR Normal Operation 64/83
The landing gear extends.
On the ECAM wheel page the landing gear indications
change from red to green and the door indications
change from amber to green as the doors close.
On the landing gear panel the unlocked indications
extinguish and the landing gear indications become
green to indicate that the gear is down and locked.
MENU
LANDING GEAR Normal Operation 65/83
These green dashes appear in flight when the
landing gear is extended. They remain displayed
until touch down. They will come on and off during
braking according to the anti skid release order.
They indicate that the antiskid is normal and
available.
Note: The blue REL indication means released and is
a label only.
ANTI SKID
AVAILABLE
MENU
LANDING GEAR Normal Operation 66/83
Airbus recommends the use of the AUTO BRK on
contaminated runways or when operating in low
visibility.
For landing today, we will use the AUTO BRK.
Seett tthhee AUTTO BRK ttoo LLO..
MENU
LANDING GEAR MENU Normal Operation 67/83
Noo,, ttoo sseett tthhee AUTTO BRK ttoo LLO,, ppuusshh oonn tthhee LLO ppbb..
LANDING GEAR MENU Normal Operation 68/83
Noo,, ttoo sseett tthhee AUTTO BRK ttoo LLO,, ppuusshh oonn tthhee LLO ppbb..
LANDING GEAR Normal Operation 69/83
The following indications indicate that the AUTO
BRK is armed:
- ON in the selected pb,
- AUTO BRK LO in green on the E/WD
- and AUTO BRK LO in green on the ECAM WHEEL
page.
Note: on the E/WD, the memo AUTO BRK LO only
appears below 800 ft AGL.
MENU
LANDING GEAR MENU Normal Operation 70/83
LANDING GEAR MENU Normal Operation 71/83
LANDING GEAR MENU
Normal Operation 72/83
During landing roll out, extension of the ground
spoilers triggers the AUTO BRK.
The DECEL light illuminates green when the
aircraft deceleration is at least 80%of the selected rate.
LANDING GEAR MENU
Normal Operation 73/83
AUTO BRK action depends on the rate selected:
- LO: braking after approximately 4 seconds,
- MED: braking after approximately 2 seconds and
higher deceleration than in LO,
- MAX: immediate braking, with max deceleration
rate. This mode is only used for take off.
LANDING GEAR Normal Operation 74/83
On the ECAM WHEEL page, watch the green
dashes. They appear during braking indicating that
the A/SKID is active.
MENU
LANDING GEAR Normal Operation 75/83
The AUTO BRK can be deselected either using the
corresponding pb on the AUTO BRK panel, or by
applying sufficient force to one brake pedal in LO and
MED, and to both brake pedals in MAX.
MENU
LANDING GEAR Normal Operation 76/83
On the ECAM WHEEL page check the brake
temperature for significant differences and high
temperatures.
A maintenance action is required when the difference
between two brakes of the same gear is greater than 150
degrees or when the mean temperature of one gear
differs by more than 200 degrees with another gear.
MENU
LANDING GEAR Normal Operation 77/83
Above 100 degrees Celsius, a green arc is
displayed over the hottest brake temperature. In this
case the brake fans must be selected on.
Swiittcchh tthhee BRK FFAN ON..
MENU
LANDING GEAR MENU Normal Operation 78/83
No, to switch the BRK FAN ON, click on the
BRK FAN pb.
LANDING GEAR MENU Normal Operation 79/83
No, to switch the BRK FAN ON, click on the
BRK FAN pb.
LANDING GEAR Normal Operation 80/83
The ON light turns white indicating that the
BRK FAN is running.
MENU
LANDING GEAR MENU Normal Operation 81/83
LANDING GEAR MENU Normal Operation 82/83
LANDING GEAR MENU Normal Operation 83/83
We have set the PARK BRK for you. Before
releasing the pedals check the BRAKE pressure
indications.
Note: As soon as the PARK BRK is ON, braking
using the pedal is no longer available.
NEXT
MMoodduulleeccoommpplleetteedd
LANDING GEAR MENU Normal Operation 84/83
LLIISSTTOOFFSSUUBBJJEECCTTSS
GENERAL
PRELIMINARILY COCKPIT PREPARATION
WALK AROUND
COCKPIT PREPARATION
TAXI
TAKE OFF
APPROACH
LANDING
PARKING
RETURN AUDIO GLOSSARY FCOM EXIT