|
SANDIA aerospace, Inc. 3700 Osuna Rd. NE, Suite 711 Albuquerque, NM 87109 305186-00 Rev. 3 SAE5-35 Altitude Data System Installation Manual This document and the information contained herein is the proprietary data of SANDIA aerospace, Inc. No part of this document may be transmitted, reproduced, or copied in any form or by any means without the prior written consent of SANDIA aerospace, Inc. Due to SANDIA aerospace’s continued product and quality improvement programs, information contained in this document is subject to change without prior notice. Copyright 2000 SANDIA aerospace, Inc., All rights reserved. Printed in USA Revision Date Description Approval -1 000908 Initial Release J. Fiala -2 030722 ECN 3379 J. Fiala -3 20040716 ECN 3429 J. Fiala Record of Revisions 1 Table Of Contents Record of Revisions .............................................................................................................. 1 Table of Contents ................................................................................................................ 2 List of Illustrations .............................................................................................................. 2 Section 1 - General Description .......................................................................................... 3 1.1 Introduction ............................................................................................................ 3 1.1.1 Product Description ....................................................................................... 3 1.2 Technical Characteristics ........................................................................................ 3 1.2.1 Physical Characteristics ................................................................................ 3 1.2.2 Operational Characteristics .......................................................................... 3 1.2.3 Gillham Grey Code Output........................................................................... 4 1.2.4 AIM Outputs ................................................................................................ 4 1.2.5 Discrete Inputs ............................................................................................. 4 1.2.6 RS-232 Outputs............................................................................................ 4 1.2.6.1 Standard Mode ..................................................................................... 4 1.2.6.2 Extended Mode..................................................................................... 5 1.2.7 Certification ................................................................................................... 5 Environmental Qualification Form ...................................................................................... 6 Section 2 - Installation Considerations ............................................................................... 7 2.1 Introduction ............................................................................................................ 7 2.2 Mounting Considerations ....................................................................................... 7 2.3 Cooling ................................................................................................................... 7 Section 3 - Installation Procedures ..................................................................................... 8 3.1 General ................................................................................................................... 8 3.2 Equipment Required ............................................................................................... 8 3.2.1 Equipment Supplied ....................................................................................... 8 3.2.2 Equipment Not Supplied .................................................................................. 8 3.2.3 AIM Annuciator ............................................................................................... 8 3.3 Mounting Tray Installation ......................................................................................... 8 3.4 Static Port Connection ........................................................................................... 9 3.5 Electrical Installation .............................................................................................. 9 3.6 Calibration ............................................................................................................ 14 3.6.1 Equipment Required .................................................................................... 14 3.6.2 Calibration Procedures ................................................................................. 15 3.6.3 Placarding .................................................................................................... 16 3.7 Continued Airworthiness ...................................................................................... 16 List Of Illustrations Figure 3-1 SAE5-35 Outline Dimensions (with tray) ...................................................... 9 Figure 3-2 J4/J5 Connector Wiring ............................................................................... 11 Figure 3-3 J4/J5 Connector Hood Assembly ................................................................. 11 Figure 3-4 J4 Pinout ...................................................................................................... 12 Figure 3-5 J5 Pinout ...................................................................................................... 12 Figure 3-6 Interconnect To Popular Transponders ........................................................ 13 Figure 3-7 Interconnect to Garmin & UPSAT GPS and MX20 .................................... 14 Figure 3-8 SAE5-35 Adjustment ................................................................................... 16 Figure 3-9 Gillham Grey Code Chart ....................................................................... 17-19 2 Section 1 General Description 1.1 INTRODUCTION This manual describes the installation of the SANDIA aerospace SAE5-35 Altitude Data System. It is intended for use by FAA certified repair stations to install the SAE5-35 Altitude Data System and includes both the mechanical and electrical installation information for the SAE5-35. Calibration and checkout procedures are included. The installer should insure that all functions are operating according to their intended purpose in their particular installation. 1.1.1 Product Description The SAE5-35 is a solid state -1000 to 35,000 foot altitude data system that converts pressure altitude into a digital output as set forth in the International Standard for SSR Pressure Altitude Transmission. The data output of the SAE5-35 is referenced to 29.92 inch HG (1013 Millibars). The SAE5- 35 has been designed to provide altitude data to GPS and Terrain Awareness Systems in addition to Mode C Transponders. The SAE5-35 outputs Gillham Grey Code to the transponder and two independent RS232 digital outputs that can be used by GPS or other systems requiring this format. Additionally, the SAE5-35 includes SANDIA aerospace’s exclusive Altitude In-flight Monitoring (AIM) feature. With the addition of an optional panel mounted switch and annunciator the AIM mode will monitor and advise the pilot if the aircraft deviates from a selected altitude. 1.2 TECHNICAL CHARACTERISTICS 1.2.1 Physical Characteristics Width: 4.87” (5.11” with mounting tray) Height: 1.06” (1.57” with mounting tray) Depth: 4.74” (4.80” with mounting tray) Weight: 0.7 lbs. (.86 lbs. with mounting tray) 1.2.2 Operational Characteristics Operating Temp. -20o C to + 55o C Altitude: 35,000 feet Voltage: 11 - 32 Vdc Current 1.0 amps maximum with heater on <100 mA quiescent Accuracy: +/- 50 feet Typical Resolution: Grey Code 100’ RS232 10’ Burst Pressure 90 in Hg Maximum Rate of Altitude Change: 12,000 Feet/Minute 3 1.2.3 Gillham Grey Code Outputs a. 10 Bits available: D4, A4, A2, A1, B4, B2, B1, C4, C2, C1 b. Bit On Impedance: Less than 5 ohms c. Bit Off Leakage: Less than 10uA d. Maximum Current per bit: 20 mA e. Minimum working current: 10 uA f. Maximum voltage per bit: 50V g. Minimum working voltage: 5V h. Bit update rate: Less than 250 mS i. Minimum strobe switching bandwidth: Greater than 10kHz 1.2.4 AIM Outputs Maximum Lamp Current: 80 mA Maximum off Voltage: 50V 1.2.5 Discrete Inputs AIM SET, Strobe and RS232 Mode Select Inputs Asserted: < 0.4 Vdc Not Asserted: > 1.7 Vdc Pull-up current: 150 uA 1.2.6 RS-232 Outputs There are two modes of operation for the RS232 outputs. The Data Mode pin, J5 pin 4 selects the data formats. 1.2.6.1 Standard Mode When the Mode pin (J5 pin 4) is open: a. Baud: 9600 b. Data bits: 8 c. Stop bit: 1 d. Parity: None e. Output rate: 1 +/- .2 seconds f. Message length: 11 bytes g. Altitude resolution: 10 foot h. Works with Garmin and Trimble GPS 4 305186-00 5 1.2.6.2 Extended Mode When the Mode pin (J5 pin 4) is grounded: a. Baud: 1200 b. Data bits: 8 c. Stop bit: 1 d. Parity: None e. Output rate: 1 +/- .2 seconds f. Message length: 17 bytes g. Altitude resolution: 10 foot h. Temperature resolution: 1 degree C i. For use with UPSAT MX20 and GPS receivers 1.2.7 Certification TSO: C88a Software: DO-178B Level C Environmental: DO-160D(C1)CAA[(SM)(UF)]XXXXXXZBBBBTBXXXX Environmental Qualification Form for the SAE5-35 Altitude Data System NOMENCLATURE: SAE5-35, Altitude Data System TYPE/MODEL/PART NO: SAE5 – 35 / 305154-00 TSO NUMBER: C88a MANUFACTURER’S SPECIFICATION AN/OR OTHER APPLICABLE SPECIFICATION: SAE5-35 INSTALLATION MANUAL P/N 305186-00 QUALIFICATION TEST PLAN, SAE5-35 ALTITUDE ENCODER. P/N AENC0051 MANUFACTURER: SANDIA AEROSPACE ADDRESS: 5445 EDITH BLVD. NE, SUITE I ALBUQUERQUE, NM 87107 REVISION & CHANGE NUMBER OF DO-160: REV D, DATED JULY 27 1997 CONDITIONS SECTION DESCRIPTION OF TESTS CONDUCTED Temperature and Altitude Low Temperature High Temperature In-Flight Loss of Cooling Altitude Decompression Overpressure 4.0 4.5.1 4.5.2 & 4.5.3 4.5.4 4.6.1 4.6.2 4.6.3 Equipment Tested to Category C1 Tested to-20°C Operating Low Temp Tested to +55°C Operating High Temp Test not Applicable 35,000 feet Test not Applicable Test not Applicable Temperature Variation 5.0 Tested to CategoryC Humidity 6.0 Tested to CategoryA Operational Shock and Crash Safety 7.0 Tested to CategoryA Vibration 8.0 Tested to Category S, Aircraft Zone 2 using vibration curve M. Tested to Category U, Helicopter Zone 2 using vibration curves F and F1. Explosion 9.0 Equipment identified as Category X, no test performed Waterproofness 10.0 Equipment identified as Category X, no test performed Fluids Susceptibility 11.0 Equipment identified as Category X, no test performed Sand and Dust 12.0 Equipment identified as Category X, no test performed Fungus 13.0 Equipment identified as Category X, no test performed Salt Spray 14.0 Equipment identified as Category X, no test performed Magnetic Effect 15.0 Equipment is categoryZ Power Input 16.0 Tested to CategoryB Voltage Spike 17.0 Tested to CategoryB Audio Frequency Susceptibility 18.0 Tested to CategoryB Induced Signal Susceptibility 19.0 Tested to CategoryB Radio Frequency Susceptibility 20.0 Tested to CategoryT Radio Frequency Emission 21.0 Tested to CategoryB Lighning Induced Transient Susceptibility22.0 Equipment identified as Category X, no test performed Lightning Direct Effects 23.0 Equipment identified as Category X, no test performed Icing 24.0 Equipment identified as Category X, no test performed Electrostatic Discharge 25.0 Equipment identified as Category X, no test performed 6 305186-00 DATE OF TEST: July 2000 Section 2 Installation Considerations 2.1 INTRODUCTION The SAE5-35 Altitude Data System simplifies installations that include GPS, Terrain Awareness Systems and other avionics that require RS232 altitude input information. The SAE5-35 provides standard Gillham Grey Code output on its 15 pin connector. Grey code is required for interface to Mode C ATCRBS and Mode S transponders. Two independent RS232 outputs are provided on the nine pin connector. The SAE5-35 also incorporates SANDIA aerospace’s exclusive Altitude In-flight Monitoring (AIM) feature that advises pilots if they deviate from their selected altitude by more than one hundred feet. The AIM feature can be installed by purchasing SANDIA aerospace’s optional annunciator/switch assembly, P/N 305217-00. Or the installer can supply his own switch and annunciator assembly(s). The main 15 pin connector follows the standard encoder interconnect used by many manufacturers. By following this convention, upgrading to the SAE5-35 is made easier. If another manufacturers encoder is being replaced, it is important to check the wiring information before plugging the existing connector into the SAE5-35. Both the Grey Code output and each of the RS232 outputs have separate drivers. This ensures that a load on one line does not load the other. Additionally, the RS232 output is available even if the enable line on the Grey Code has not been enabled by the transponder. The SAE5-35 does not require warm up unless the outside temperature is below 20 degrees C. When warm up time is required, the internal heater is capable of warming the SAE5-35 from -20 degrees C to operating temperature in less than two minutes. 2.2 MOUNTING CONSIDERATIONS The SAE5-35 can be mounted in any axis and either inside or outside the pressure vessel. Mounting should allow for as short a pressure line as possible from the encoder to the altimeter. Be sure to allow an ample service loop on the cable to allow for calibration of the SAE5-35 CAUTION: DO NOT mount the SAE5-35 in the direct airstream or near either the hot or cold air ducts. 2.3 COOLING The SAE5-35 does not require external cooling. 7 3.1 GENERAL The SAE5-35 is supplied with a mounting tray and solder type mating connectors. It is important that proper solder techniques be observed in attaching wires to the mating connectors. Failure to do so could result in a failure in the connection and cause intermittent or non operation of the SAE5-35. Section 3 Installation Procedures 3.2 EQUIPMENT REQUIRED 3.2.1
Supplied SAE5-35 System 705154-00 Includes: SAE5-35 Encoder 305154-00 SAE5-35 Installation Manual 305186-00 SAE5-35 Installation Kit 305216-00 15 Pin Mating Connector 305215 15 Pin Connector Hood 305208 9 Pin Mating Connector 305214 9 Pin Connector Hood 305207 Mounting Tray 305145 Knurled Holdown Nut 305189 3.2.2
Required but not supplied Number 6-32 mounting screws Static port fitting 3.2.3
Optional Equipment AIM Annunciator, Installer supplied or Sandia Part Number 307217-00 3.3 MOUNTING TRAY INSTALLATION The mounting tray is mounted to the airframe using either three or four number 6-32 screws. The mounting hole pattern for the SAE5-35 mounting tray contains five holes. For new installations, it is recommended that the four corner holes be used to mount the SAE5-35 tray. The fifth hole has been added to facilitate upgrades from other manufactures encoders. Refer to the SAE5-35 tray dimensions in Figure 3-1 to determine if the hole pattern of the removed system match the hole pattern of the SAE5-35 mounting tray. 8 305186-00 3.4 STATIC PORT CONNECTION A standard 1/8 - 27 NPT brass fitting is provided on the front plate of the encoder for attaching to the aircraft static air system. An adapter may be used to convert this to match the aircraft static plumbing. When attaching the mating fitting, make sure that it is secure and free from leaks that can induce errors in the static system. In installations where an existing encoder is being replaced, the existing tubing and fittings should be examined for any damage or deterioration and replaced if necessary. To reduce the likelihood of the brass fitting rotating while installing the static lines, a “D” shaped hole is used to mount the brass fitting into the front panel. Upon completion of installation of the SAE5-35, a Case Leak test is to be performed per FAR Part 43 Appendix E NOTE: Since significant force can be applied to the encoder during static fitting installation, dual wrench techniques are always recommended to avoid damage to the encoder. 3.5 ELECTRICAL INSTALLATION The SAE5-35 is designed to operate from 11-32Vdc without any special wiring considerations. Power can be supplied from the transponder’s switched A+ output, the transponder circuit breaker or from the aircraft buss. If supplied from the aircraft buss, the line must be protected with a 2 amp fuse Figure 3-1 SAE5-35 Outline Dimensions (with tray) 9 J4 J5 or circuit breaker. SAE document AS8003 Minimum Performance Standard for Automatic Pressure Altitude Reporting Code Generating Equipment states that “a means shall be incorporated in the equipment to indicate the loss of electrical power or the effect thereof, unless the electrical power to operate the code generating equipment is supplied by an ATC Transponder which also supplies an indication of this power loss.” This is typically accomplished by using the switched A+ output from the transponder or by connecting the SAE5-35 power input to the transponder circuit breaker. Alternatively, the two power pins, 8 and 14, are internally connected in the SAE5-35. Only one of these connections is necessary to supply power to the unit. The unused connection can be used to drive a panel-mounted indicator if desired. All transponder functions including the Grey code output are on the 15 pin connector J4. The RS232 digital outputs for GPS and other avionics requiring this format as well as the AIM function are on the 9 pin connector J5. The Grey code output on the transponder is disabled whenever Mode C on the transponder is not selected. Note: The RS232 serial data output is always present whenever there is power to the SAE5-35 and the warm up time is completed, even when the Strobe/Enable line is not grounded. Note: If power is supplied from the transponder, the RS232 and AIM functions will be inoperative when the transponder is turned off or removed from the aircraft. Grounding the Strobe/Enable line on J4 pin 6 will enable the transponder Grey code data. There are three methods used to do this. 1. Permanently grounding this line. 2. The transponder provides a switched ground enable signal. 3. The transponder provides a strobe-ground enable signal. The SAE5-35 is compatible with all three systems, refer to the appropriate transponder installation manual for detail. Interconnect information for the most popular transponders can be found in Figure 3-6. For other makes of transponders, refer to the manufacturers installation manual. Note: If the transponder being interfaced has a strobe output, the AIM function will not operate properly and should not be connected. While several manufacturers use RS232 digital altitude data, their formats and baud rates may vary. The SAE5-35 can accommodate most data formats by either grounding or leaving pin 4 on J5 open. If pin 4 is left open, the output baud rate is 9600. If pin 4 is grounded, the output baud rate is 1200. The RS232 interconnect information can be found in Figure 3-7. Interconnect information for the most popular transponders can be found in Figures 3-6. The RS232 interconnect information can be found in Figure 3-7. 10 305186-00 Figure 3-2 J4/J5 Connector Wiring Figure 3-3 J4/J5 Connector Hood Assembly 11 The SAE5-35 uses Sub-D solder cup connectors with screw lock assemblies. Proper wire attachment and assembly of the screw locks and connector hood are shown in Figure 3-2 and 3-3. It is recommended that each wire and solder cup be covered with a piece of shrink tubing or other insulator. J4 J5 J4 Notes: 1. J4 is 15 Pin receptacle 2. Pin 6 may be strobed or permanently grounded. Pin 6 must be grounded for AIM function to be operational. 3. Power and ground wires (pins 8, 14 & 15) are 20 AWG. All other wires are 22AWG unless otherwise noted. 4. Pin 8 and 14 are internally connected in the SAE5-35. Only one line is necessary to supply power to the unit. The unused power pin may be used as a power loss indicator if desired. 5. The Garmin 430/530 must be set to Icarus RS232 format. J5 Notes: 1. J5 is 9 Pin receptacle 2. Maximum lamp current 80mA 3. All wires are 22AWG unless otherwise noted. 4. AIM switch is a momentary contact 5. Ground pin 4 for 1200 baud Leave pin 4 open for 9600 baud (see Paragraph 1.2.6.1 & 1.2.6.2 for details). 6. If the AIM function uses annunciator lamps provided by the installer, they should be appropriately labeled. The lamp connected to pin 9 should be labeled ‘ALT’ and the lamp connected to pin 8 should be labeled ‘SET’. Figure 3-4 J4 Pinout Figure 3-5 J5 Pinout 12 305186-00 SAE5-35 J4 Function Bendix TPR2060 Bendix TR641A/B Cessna RT359T, RT459A, RT859A Garmin GTX300 Series Honeywell KT70/71 (Connector JKT701) Honeywell KT76A/78A Honeywell KXP Narco AT50/A, AT150 Narco AT5, AT6/A UPSAT SL70 Wilcox 1014A 1 D4 No Connection N 10 18 8 No Connection V No Connection No Connection 35 C 2 A1 4 A 14 3 M M G 7 2 13 k 3 A2 6 B 13 5 K K H 6 4 31 c 4 A4 8 C 15 6 J J J 8 8 12 W 5 B1 9 D 19 9 E E K 12 9 33 T 6 Strobe/Enable Aircraft Ground Aircraft Ground 11 Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground 5 12 Aircraft Ground Aircraft Ground 7 Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground 8 Aircraft Power Note1 Note1 9 or per Note 1 Note 1 Note1 Note1 Note1 18 or per Note 1 13 or per Note 1 Note 1 Note1 9 B2 10 E 17 11 C C L 10 10 14 L 10 B4 11 F 16 12 B B M 9 11 32 D 11 C1 3 H 21 10 D D P 14 1 16 P 12 C4 7 K 20 7 H H S 13 5 15 Z 13 C2 5 J 18 4 L L R 11 3 34 f 14 Aircraft Power Note1 Note1 Note1 Note1 Note1 Note1 Note1 Note1 Note1 Note1 Note1 15 Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Aircraft Ground Figure 3-6 Interconnect for popular transponders 13 Notes: 1. The two power pins, 8 and 14, are internally connected in the SAE5-35. Only one of these connections is necessary to supply power to the unit. The unused connection can be used to drive a panel-mounted indicator if desired. SAE5-35 J5 Function Garmin 430 P4001 Garmin 530 P5001 UPSAT GX60/65 37 Pin Connector UPSAT MX20 P2 1 RS232 TX1 57 57 4or 21 21 2 RS232 TX2 Note1 Note1 Note1 Note1 3 N/C No Connection No Connection No Connection No Connection 4 RS232 Mode Select No Connection No Connection Aircraft GroundAircraft Ground 5 RS232 Return 77 or 78 77 or 78 25 3 6 RS232 Shield Open Note 3 Open Note 3 Open Note 3 Open Note 3 7 AIM 'SET' Switch Note4 Note4 Note4 Note4 8 AIM 'SET' Lamp Note4 Note4 Note4 Note4 9 AIM 'ALT' Lamp Note 4 Note4 Note4 Note4 Figure 3-7 J5 interconnect With Garmin and UPSAT Systems 14 Notes: 1. The SAE5-35 has two independent RS232 outputs. RS232 TX2 can be connected to a second sysytem in the same manner as RS232 TX1 2. The RS232 wires are 22 AWG twisted pair. 3. Shield grounds are ground at the SAE5-35 and open at the unit being interfaced. 4. See Figure 3-5 for AIM function interconnect wiring. 305186-00 3.6 CALIBRATION The SAE5-35 is calibrated at the factory to a pressure datum traceable to the National Bureau of Standards. However, when the encoder is installed in the aircraft it must be recalibrated to correspondence to the primary flight altimeter, refer to FAR 91.217 and FAR 91.413 for details. This calibration ensures that the altitude code generated from the SAE5-35 is within 125 feet of the altitude displayed to the pilot. 3.6.1 Equipment Required 1. A calibrated pitot-static test set capable of pumping the system from –1000 feet up the maximum test altitude. 2. A calibrated transponder ramp tester capable of displaying the encoder altitude information. 15 3.6.2 Calibration Procedures Note: The Primary Flight Altimeter must be calibrated per part 43 section E. Verify compliance with AC-43.13 as applicable. 1. Connect the pitot-static test set to the aircraft static system. The SAE5-35 must be connected to the aircraft static line near the flight altimeter and the two altitude adjustments buttons must be accessible. Apply power to the altitude encoder and the ATC transponder and allow the encoder to stabilize. Set primary flight altimeter to 29.92 inches of mercury. 2. Apply vacuum from the pitot-static test set to obtain an altimeter reading of 34,800 feet (or 100 feet below the maximum test altitude specified in Part 43, appendix F.) 3. Slowly increase altitude and note the flight altimeter at the encoder transition point. If the transition point is not 34,850 +/- 30 feet (or between –80 feet and –20 feet below the maximum test altitude), press the increase button (behind slot A) or decrease button (behind slot B) until the encoder transition point is within tolerance. 4. Increase altitude to obtain an altimeter reading of 35,000 feet (or 100 feet above the maximum altitude specified in Part 43, appendix F.) 5. Slowly decrease altitude and read the flight altimeter at the encoder transition point. Verify the transition point is 34,950 +/- 30 feet (or between 20 feet and 80 feet above the maximum test altitude.) If necessary, press the increase button (behind slot A) or decrease button (behind slot B) until the encoder transition point is within tolerance. 6. Apply pressure from the pitot-static test set to obtain an altimeter reading of -800feet 7. Slowly decrease altitude and read the flight altimeter at the encoder –800 foot to –900- transition point. If the transition point is higher than -880 feet, hold the increase altitude button (behind slot A) while pressing and releasing the decrease altitude button (behind slot B) until the transition point is –850 +/- 30feet. If the transition point is lower than - 820 feet, hold the decrease altitude button (behind slot B) while pressing and releasing the increase altitude button (behind slot A) until the transition point is –850 +/- 30feet. 8. Apply pressure from the pitot-static test set to obtain an altimeter reading of -1000feet 9. Slowly increase altitude and read the flight altimeter at the encoder –1000 foot to –900- transition point. If the transition point is higher than -920 feet, hold the increase altitude button (behind slot A) while pressing and releasing the decrease altitude button (behind slot B) until the transition point is –950 +/- 30 feet. If the transition point is lower than - 16 980 feet, hold the decrease altitude button (behind slot B) while pressing and releasing the increase altitude button (behind slot A) until the transition point is –950 +/- 30 feet. 10. Repeat steps 2 through 10 until the transition points and the flight altimeter are within tolerance for both low and high altitudes. Verify several test points throughout the range to assure correspondence between the SAE5-35 and the flight altimeter. 305186-00 3.6.3 Placarding We recommend that the altimeter used for flight reference and the SAE5-35 be placarded with the following information: Replacement or re-calibration of the altimeter used for flight reference requires re-calibration of SAE5-35 Altitude Encoder. Altitude encoded to feet. Figure 3-8 SAE5-35 Adjustment 3.7 CONTINUED AIRWORTHINESS The SAE5-35 requires calibration every 24 months per FAR 91.411. All other maintenance of the SAE5-35 is on condition only. OOPS ! The SAE5-35 can be reset to factory settings by appling power to the unit while simultaneously pressing both adjustments A & B 17 Altitude D4 A1 A2 A4 B1 B2 B4 C1 C2 C4 -1000 0 0 0 0 0 0 0 0 1 0 -900 0 0 0 0 0 0 0 1 1 0 -800 0 0 0 0 0 0 0 1 0 0 -700 0 0 0 0 0 0 1 1 0 0 -600 0 0 0 0 0 0 1 1 1 0 -500 0 0 0 0 0 0 1 0 1 0 -400 0 0 0 0 0 0 1 0 1 1 -300 0 0 0 0 0 0 1 0 0 1 -200 0 0 0 0 0 1 1 0 0 1 -100 0 0 0 0 0 1 1 0 1 1 0 0 0 0 0 0 1 1 0 1 0 100 0 0 0 0 0 1 1 1 1 0 200 0 0 0 0 0 1 1 1 0 0 300 0 0 0 0 0 1 0 1 0 0 400 0 0 0 0 0 1 0 1 1 0 500 0 0 0 0 0 1 0 0 1 0 600 0 0 0 0 0 1 0 0 1 1 700 0 0 0 0 0 1 0 0 0 1 800 0 0 0 0 1 1 0 0 0 1 900 0 0 0 0 1 1 0 0 1 1 1000 0 0 0 0 1 1 0 0 1 0 1100 0 0 0 0 1 1 0 1 1 0 1200 0 0 0 0 1 1 0 1 0 0 1300 0 0 0 0 1 1 1 1 0 0 1400 0 0 0 0 1 1 1 1 1 0 1500 0 0 0 0 1 1 1 0 1 0 1600 0 0 0 0 1 1 1 0 1 1 1700 0 0 0 0 1 1 1 0 0 1 1800 0 0 0 0 1 0 1 0 0 1 1900 0 0 0 0 1 0 1 0 1 1 2000 0 0 0 0 1 0 1 0 1 0 2100 0 0 0 0 1 0 1 1 1 0 2200 0 0 0 0 1 0 1 1 0 0 2300 0 0 0 0 1 0 0 1 0 0 2400 0 0 0 0 1 0 0 1 1 0 2500 0 0 0 0 1 0 0 0 1 0 2600 0 0 0 0 1 0 0 0 1 1 2700 0 0 0 0 1 0 0 0 0 1 2800 0 0 0 1 1 0 0 0 0 1 2900 0 0 0 1 1 0 0 0 1 1 3000 0 0 0 1 1 0 0 0 1 0 3100 0 0 0 1 1 0 0 1 1 0 3200 0 0 0 1 1 0 0 1 0 0 3300 0 0 0 1 1 0 1 1 0 0 3400 0 0 0 1 1 0 1 1 1 0 3500 0 0 0 1 1 0 1 0 1 0 3600 0 0 0 1 1 0 1 0 1 1 3700 0 0 0 1 1 0 1 0 0 1 3800 0 0 0 1 1 1 1 0 0 1 3900 0 0 0 1 1 1 1 0 1 1 4000 0 0 0 1 1 1 1 0 1 0 4100 0 0 0 1 1 1 1 1 1 0 4200 0 0 0 1 1 1 1 1 0 0 4300 0 0 0 1 1 1 0 1 0 0 4400 0 0 0 1 1 1 0 1 1 0 4500 0 0 0 1 1 1 0 0 1 0 4600 0 0 0 1 1 1 0 0 1 1 4700 0 0 0 1 1 1 0 0 0 1 4800 0 0 0 1 0 1 0 0 0 1 4900 0 0 0 1 0 1 0 0 1 1 5000 0 0 0 1 0 1 0 0 1 0 5100 0 0 0 1 0 1 0 1 1 0 5200 0 0 0 1 0 1 0 1 0 0 5300 0 0 0 1 0 1 1 1 0 0 5400 0 0 0 1 0 1 1 1 1 0 5500 0 0 0 1 0 1 1 0 1 0 5600 0 0 0 1 0 1 1 0 1 1 5700 0 0 0 1 0 1 1 0 0 1 5800 0 0 0 1 0 0 1 0 0 1 5900 0 0 0 1 0 0 1 0 1 1 6000 0 0 0 1 0 0 1 0 1 0 6100 0 0 0 1 0 0 1 1 1 0 6200 0 0 0 1 0 0 1 1 0 0 6300 0 0 0 1 0 0 0 1 0 0 6400 0 0 0 1 0 0 0 1 1 0 6500 0 0 0 1 0 0 0 0 1 0 6600 0 0 0 1 0 0 0 0 1 1 6700 0 0 0 1 0 0 0 0 0 1 6800 0 0 1 1 0 0 0 0 0 1 6900 0 0 1 1 0 0 0 0 1 1 7000 0 0 1 1 0 0 0 0 1 0 7100 0 0 1 1 0 0 0 1 1 0 7200 0 0 1 1 0 0 0 1 0 0 7300 0 0 1 1 0 0 1 1 0 0 7400 0 0 1 1 0 0 1 1 1 0 7500 0 0 1 1 0 0 1 0 1 0 7600 0 0 1 1 0 0 1 0 1 1 7700 0 0 1 1 0 0 1 0 0 1 7800 0 0 1 1 0 1 1 0 0 1 7900 0 0 1 1 0 1 1 0 1 1 8000 0 0 1 1 0 1 1 0 1 0 8100 0 0 1 1 0 1 1 1 1 0 8200 0 0 1 1 0 1 1 1 0 0 8300 0 0 1 1 0 1 0 1 0 0 8400 0 0 1 1 0 1 0 1 1 0 8500 0 0 1 1 0 1 0 0 1 0 8600 0 0 1 1 0 1 0 0 1 1 8700 0 0 1 1 0 1 0 0 0 1 8800 0 0 1 1 1 1 0 0 0 1 8900 0 0 1 1 1 1 0 0 1 1 9000 0 0 1 1 1 1 0 0 1 0 9100 0 0 1 1 1 1 0 1 1 0 9200 0 0 1 1 1 1 0 1 0 0 9300 0 0 1 1 1 1 1 1 0 0 9400 0 0 1 1 1 1 1 1 1 0 9500 0 0 1 1 1 1 1 0 1 0 9600 0 0 1 1 1 1 1 0 1 1 9700 0 0 1 1 1 1 1 0 0 1 9800 0 0 1 1 1 0 1 0 0 1 9900 0 0 1 1 1 0 1 0 1 1 10000 0 0 1 1 1 0 1 0 1 0 10100 0 0 1 1 1 0 1 1 1 0 10200 0 0 1 1 1 0 1 1 0 0 10300 0 0 1 1 1 0 0 1 0 0 10400 0 0 1 1 1 0 0 1 1 0 10500 0 0 1 1 1 0 0 0 1 0 Altitude D4 A1 A2 A4 B1 B2 B4 C1 C2 C4 Figure 3-9 Gillham Grey Code Chart 18 305186-00 10600 0 0 1 1 1 0 0 0 1 1 10700 0 0 1 1 1 0 0 0 0 1 10800 0 0 1 0 1 0 0 0 0 1 10900 0 0 1 0 1 0 0 0 1 1 11000 0 0 1 0 1 0 0 0 1 0 11100 0 0 1 0 1 0 0 1 1 0 11200 0 0 1 0 1 0 0 1 0 0 11300 0 0 1 0 1 0 1 1 0 0 11400 0 0 1 0 1 0 1 1 1 0 11500 0 0 1 0 1 0 1 0 1 0 11600 0 0 1 0 1 0 1 0 1 1 11700 0 0 1 0 1 0 1 0 0 1 11800 0 0 1 0 1 1 1 0 0 1 11900 0 0 1 0 1 1 1 0 1 1 12000 0 0 1 0 1 1 1 0 1 0 12100 0 0 1 0 1 1 1 1 1 0 12200 0 0 1 0 1 1 1 1 0 0 12300 0 0 1 0 1 1 0 1 0 0 12400 0 0 1 0 1 1 0 1 1 0 12500 0 0 1 0 1 1 0 0 1 0 12600 0 0 1 0 1 1 0 0 1 1 12700 0 0 1 0 1 1 0 0 0 1 12800 0 0 1 0 0 1 0 0 0 1 12900 0 0 1 0 0 1 0 0 1 1 13000 0 0 1 0 0 1 0 0 1 0 13100 0 0 1 0 0 1 0 1 1 0 13200 0 0 1 0 0 1 0 1 0 0 13300 0 0 1 0 0 1 1 1 0 0 13400 0 0 1 0 0 1 1 1 1 0 13500 0 0 1 0 0 1 1 0 1 0 13600 0 0 1 0 0 1 1 0 1 1 13700 0 0 1 0 0 1 1 0 0 1 13800 0 0 1 0 0 0 1 0 0 1 13900 0 0 1 0 0 0 1 0 1 1 14000 0 0 1 0 0 0 1 0 1 0 14100 0 0 1 0 0 0 1 1 1 0 14200 0 0 1 0 0 0 1 1 0 0 14300 0 0 1 0 0 0 0 1 0 0 14400 0 0 1 0 0 0 0 1 1 0 14500 0 0 1 0 0 0 0 0 1 0 14600 0 0 1 0 0 0 0 0 1 1 14700 0 0 1 0 0 0 0 0 0 1 14800 0 1 1 0 0 0 0 0 0 1 14900 0 1 1 0 0 0 0 0 1 1 15000 0 1 1 0 0 0 0 0 1 0 15100 0 1 1 0 0 0 0 1 1 0 15200 0 1 1 0 0 0 0 1 0 0 15300 0 1 1 0 0 0 1 1 0 0 15400 0 1 1 0 0 0 1 1 1 0 15500 0 1 1 0 0 0 1 0 1 0 15600 0 1 1 0 0 0 1 0 1 1 15700 0 1 1 0 0 0 1 0 0 1 15800 0 1 1 0 0 1 1 0 0 1 15900 0 1 1 0 0 1 1 0 1 1 16000 0 1 1 0 0 1 1 0 1 0 16100 0 1 1 0 0 1 1 1 1 0 16200 0 1 1 0 0 1 1 1 0 0 16300 0 1 1 0 0 1 0 1 0 0 16400 0 1 1 0 0 1 0 1 1 0 16500 0 1 1 0 0 1 0 0 1 0 16600 0 1 1 0 0 1 0 0 1 1 16700 0 1 1 0 0 1 0 0 0 1 16800 0 1 1 0 1 1 0 0 0 1 16900 0 1 1 0 1 1 0 0 1 1 17000 0 1 1 0 1 1 0 0 1 0 17100 0 1 1 0 1 1 0 1 1 0 17200 0 1 1 0 1 1 0 1 0 0 17300 0 1 1 0 1 1 1 1 0 0 17400 0 1 1 0 1 1 1 1 1 0 17500 0 1 1 0 1 1 1 0 1 0 17600 0 1 1 0 1 1 1 0 1 1 17700 0 1 1 0 1 1 1 0 0 1 17800 0 1 1 0 1 0 1 0 0 1 17900 0 1 1 0 1 0 1 0 1 1 18000 0 1 1 0 1 0 1 0 1 0 18100 0 1 1 0 1 0 1 1 1 0 18200 0 1 1 0 1 0 1 1 0 0 18300 0 1 1 0 1 0 0 1 0 0 18400 0 1 1 0 1 0 0 1 1 0 18500 0 1 1 0 1 0 0 0 1 0 18600 0 1 1 0 1 0 0 0 1 1 18700 0 1 1 0 1 0 0 0 0 1 18800 0 1 1 1 1 0 0 0 0 1 18900 0 1 1 1 1 0 0 0 1 1 19000 0 1 1 1 1 0 0 0 1 0 19100 0 1 1 1 1 0 0 1 1 0 19200 0 1 1 1 1 0 0 1 0 0 19300 0 1 1 1 1 0 1 1 0 0 19400 0 1 1 1 1 0 1 1 1 0 19500 0 1 1 1 1 0 1 0 1 0 19600 0 1 1 1 1 0 1 0 1 1 19700 0 1 1 1 1 0 1 0 0 1 19800 0 1 1 1 1 1 1 0 0 1 19900 0 1 1 1 1 1 1 0 1 1 20000 0 1 1 1 1 1 1 0 1 0 20100 0 1 1 1 1 1 1 1 1 0 20200 0 1 1 1 1 1 1 1 0 0 20300 0 1 1 1 1 1 0 1 0 0 20400 0 1 1 1 1 1 0 1 1 0 20500 0 1 1 1 1 1 0 0 1 0 20600 0 1 1 1 1 1 0 0 1 1 20700 0 1 1 1 1 1 0 0 0 1 20800 0 1 1 1 0 1 0 0 0 1 20900 0 1 1 1 0 1 0 0 1 1 21000 0 1 1 1 0 1 0 0 1 0 21100 0 1 1 1 0 1 0 1 1 0 21200 0 1 1 1 0 1 0 1 0 0 21300 0 1 1 1 0 1 1 1 0 0 21400 0 1 1 1 0 1 1 1 1 0 21500 0 1 1 1 0 1 1 0 1 0 21600 0 1 1 1 0 1 1 0 1 1 21700 0 1 1 1 0 1 1 0 0 1 21800 0 1 1 1 0 0 1 0 0 1 21900 0 1 1 1 0 0 1 0 1 1 22000 0 1 1 1 0 0 1 0 1 0 22100 0 1 1 1 0 0 1 1 1 0 22200 0 1 1 1 0 0 1 1 0 0 22300 0 1 1 1 0 0 0 1 0 0 22400 0 1 1 1 0 0 0 1 1 0 22500 0 1 1 1 0 0 0 0 1 0 22600 0 1 1 1 0 0 0 0 1 1 22700 0 1 1 1 0 0 0 0 0 1 Altitude D4 A1 A2 A4 B1 B2 B4 C1 C2 C4 Altitude D4 A1 A2 A4 B1 B2 B4 C1 C2 C4 19 22800 0 1 0 1 0 0 0 0 0 1 22900 0 1 0 1 0 0 0 0 1 1 23000 0 1 0 1 0 0 0 0 1 0 23100 0 1 0 1 0 0 0 1 1 0 23200 0 1 0 1 0 0 0 1 0 0 23300 0 1 0 1 0 0 1 1 0 0 23400 0 1 0 1 0 0 1 1 1 0 23500 0 1 0 1 0 0 1 0 1 0 23600 0 1 0 1 0 0 1 0 1 1 23700 0 1 0 1 0 0 1 0 0 1 23800 0 1 0 1 0 1 1 0 0 1 23900 0 1 0 1 0 1 1 0 1 1 24000 0 1 0 1 0 1 1 0 1 0 24100 0 1 0 1 0 1 1 1 1 0 24200 0 1 0 1 0 1 1 1 0 0 24300 0 1 0 1 0 1 0 1 0 0 24400 0 1 0 1 0 1 0 1 1 0 24500 0 1 0 1 0 1 0 0 1 0 24600 0 1 0 1 0 1 0 0 1 1 24700 0 1 0 1 0 1 0 0 0 1 24800 0 1 0 1 1 1 0 0 0 1 24900 0 1 0 1 1 1 0 0 1 1 25000 0 1 0 1 1 1 0 0 1 0 25100 0 1 0 1 1 1 0 1 1 0 25200 0 1 0 1 1 1 0 1 0 0 25300 0 1 0 1 1 1 1 1 0 0 25400 0 1 0 1 1 1 1 1 1 0 25500 0 1 0 1 1 1 1 0 1 0 25600 0 1 0 1 1 1 1 0 1 1 25700 0 1 0 1 1 1 1 0 0 1 25800 0 1 0 1 1 0 1 0 0 1 25900 0 1 0 1 1 0 1 0 1 1 26000 0 1 0 1 1 0 1 0 1 0 26100 0 1 0 1 1 0 1 1 1 0 26200 0 1 0 1 1 0 1 1 0 0 26300 0 1 0 1 1 0 0 1 0 0 26400 0 1 0 1 1 0 0 1 1 0 26500 0 1 0 1 1 0 0 0 1 0 26600 0 1 0 1 1 0 0 0 1 1 26700 0 1 0 1 1 0 0 0 0 1 26800 0 1 0 0 1 0 0 0 0 1 26900 0 1 0 0 1 0 0 0 1 1 27000 0 1 0 0 1 0 0 0 1 0 27100 0 1 0 0 1 0 0 1 1 0 27200 0 1 0 0 1 0 0 1 0 0 27300 0 1 0 0 1 0 1 1 0 0 27400 0 1 0 0 1 0 1 1 1 0 27500 0 1 0 0 1 0 1 0 1 0 27600 0 1 0 0 1 0 1 0 1 1 27700 0 1 0 0 1 0 1 0 0 1 27800 0 1 0 0 1 1 1 0 0 1 27900 0 1 0 0 1 1 1 0 1 1 28000 0 1 0 0 1 1 1 0 1 0 28100 0 1 0 0 1 1 1 1 1 0 28200 0 1 0 0 1 1 1 1 0 0 28300 0 1 0 0 1 1 0 1 0 0 28400 0 1 0 0 1 1 0 1 1 0 28500 0 1 0 0 1 1 0 0 1 0 28600 0 1 0 0 1 1 0 0 1 1 28700 0 1 0 0 1 1 0 0 0 1 28800 0 1 0 0 0 1 0 0 0 1 Altitude D4 A1 A2 A4 B1 B2 B4 C1 C2 C4 Altitude D4 A1 A2 A4 B1 B2 B4 C1 C2 C4 28900 0 1 0 0 0 1 0 0 1 1 29000 0 1 0 0 0 1 0 0 1 0 29100 0 1 0 0 0 1 0 1 1 0 29200 0 1 0 0 0 1 0 1 0 0 29300 0 1 0 0 0 1 1 1 0 0 29400 0 1 0 0 0 1 1 1 1 0 29500 0 1 0 0 0 1 1 0 1 0 29600 0 1 0 0 0 1 1 0 1 1 29700 0 1 0 0 0 1 1 0 0 1 29800 0 1 0 0 0 0 1 0 0 1 29900 0 1 0 0 0 0 1 0 1 1 30000 0 1 0 0 0 0 1 0 1 0 30100 0 1 0 0 0 0 1 1 1 0 30200 0 1 0 0 0 0 1 1 0 0 30300 0 1 0 0 0 0 0 1 0 0 30400 0 1 0 0 0 0 0 1 1 0 30500 0 1 0 0 0 0 0 0 1 0 30600 0 1 0 0 0 0 0 0 1 1 30700 0 1 0 0 0 0 0 0 0 1 30800 1 1 0 0 0 0 0 0 0 1 30900 1 1 0 0 0 0 0 0 1 1 31000 1 1 0 0 0 0 0 0 1 0 31100 1 1 0 0 0 0 0 1 1 0 31200 1 1 0 0 0 0 0 1 0 0 31300 1 1 0 0 0 0 1 1 0 0 31400 1 1 0 0 0 0 1 1 1 0 31500 1 1 0 0 0 0 1 0 1 0 31600 1 1 0 0 0 0 1 0 1 1 31700 1 1 0 0 0 0 1 0 0 1 31800 1 1 0 0 0 1 1 0 0 1 31900 1 1 0 0 0 1 1 0 1 1 32000 1 1 0 0 0 1 1 0 1 0 32100 1 1 0 0 0 1 1 1 1 0 32200 1 1 0 0 0 1 1 1 0 0 32300 1 1 0 0 0 1 0 1 0 0 32400 1 1 0 0 0 1 0 1 1 0 32500 1 1 0 0 0 1 0 0 1 0 32600 1 1 0 0 0 1 0 0 1 1 32700 1 1 0 0 0 1 0 0 0 1 32800 1 1 0 0 1 1 0 0 0 1 32900 1 1 0 0 1 1 0 0 1 1 33000 1 1 0 0 1 1 0 0 1 0 33100 1 1 0 0 1 1 0 1 1 0 33200 1 1 0 0 1 1 0 1 0 0 33300 1 1 0 0 1 1 1 1 0 0 33400 1 1 0 0 1 1 1 1 1 0 33500 1 1 0 0 1 1 1 0 1 0 33600 1 1 0 0 1 1 1 0 1 1 33700 1 1 0 0 1 1 1 0 0 1 33800 1 1 0 0 1 0 1 0 0 1 33900 1 1 0 0 1 0 1 0 1 1 34000 1 1 0 0 1 0 1 0 1 0 34100 1 1 0 0 1 0 1 1 1 0 34200 1 1 0 0 1 0 1 1 0 0 34300 1 1 0 0 1 0 0 1 0 0 34400 1 1 0 0 1 0 0 1 1 0 34500 1 1 0 0 1 0 0 0 1 0 34600 1 1 0 0 1 0 0 0 1 1 34700 1 1 0 0 1 0 0 0 0 1 34800 1 1 0 1 1 0 0 0 0 1 34900 1 1 0 1 1 0 0 0 1 1 35000 1 1 0 1 1 0 0 0 1 0 | 
IP卡
狗仔卡
发表于 2009-3-16 15:57:14
分享
收藏
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
发表于 2010-3-28 15:47:54