- 注册时间
- 2011-11-30
- 最后登录
- 2011-11-30
- 在线时间
- 0 小时
- 阅读权限
- 10
- 积分
- 0
- 帖子
- 2
- 精华
- 0
- UID
- 10954

|
Installation of the wheel
; P1 B9 Y4 ?/ D1 \5 m5 W0 O
. |, r2 W% x) H2 M+ i4 v(a) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces.
* l0 N- D" n, Q/ b* W$ }8 w6 c3 s# f: C. e$ q
(b) Install the wheel, with the valve outboard, with a handling tool. : M6 E. W* F: G) w( r9 S9 X" I* m) L
(c) Remove the PROTECTOR NLG (J47548)
! M) ^5 f3 c4 ?, [. G( w8 j. D
* d- k1 S8 R3 z$ J# e8 O/ M" k7 v (d) Apply a light coat of Material No. 04-004* (COMMON GREASES) or Material No. 04-022* (COMMON GREASES) or Material No. 04-035* (COMMON GREASES) on the axle.
9 P8 a s; O @) E5 h: O# }* Y7 l3 |/ S0 B6 |. |( T0 ]6 T
(e) Install the axle nut (10). c. W9 |% i1 n1 n
! `" `0 C+ [! y. R) }9 g
(f) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 21.80 m.daN (160.77 lbf.ft) with the ADAPTOR NLG (J47549) . ; M& @5 G M# e" [2 L1 G
; @0 F9 j5 \7 Q) D; z+ R, z(g) Prevent rotation of the wheel and loosen the axle nut (10).
% ]1 ~; N$ c6 o6 |* Z. n9 g; B* H1 Q8 D8 ^* ?2 p
(h) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 10.85 m.daN (80.01 lbf.ft). - m& Z+ J# D7 O' F+ D% L- d
" g5 o0 q" q' D
(i) Tighten the axle nut (10) until the holes for the bolts (5) are aligned. " T1 h. n9 N! K1 v
& c* T$ `& A5 `2 k
(j) Turn the wheel and make sure that the wheel is installed correctly. : t1 p0 Y1 A% ?8 B7 e2 r) S
$ E4 ?* N' i! P, u2 ^, _1 Q(k) Install the casing (9). " \- O b8 e& e) c3 d5 h
! \1 m: I$ n6 v
(l) Install the bolts (5), the washers (2) and the new IPC-CSN (32-21-13-03-070) nuts (3) .
& t% U; O5 ~. ?8 a& a0 E
0 o3 u% X8 B9 t3 c2 w B# s+ }(m) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in) and safety them with the new IPC-CSN (32-21-13-03-060) cotter pins (4) .
- u) [4 U8 Y/ g3 J# ]- ~% O这是前轮安装工卡 请问红色的那句话怎么翻译 谢谢。 |
|