- 注册时间
- 2011-11-30
- 最后登录
- 2011-11-30
- 在线时间
- 0 小时
- 阅读权限
- 10
- 积分
- 0
- 帖子
- 2
- 精华
- 0
- UID
- 10954
|
Installation of the wheel ( x! p8 V: W/ D7 _: ~
' \- v! e6 O1 s9 ~(a) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces.
. Y# T6 ?0 m( |& g8 M* e! `$ s e
~% _. w! P! N(b) Install the wheel, with the valve outboard, with a handling tool. 1 E4 U$ G- b. U- w! ]
(c) Remove the PROTECTOR NLG (J47548) ' V h4 ]1 s2 ^: C( T3 a
1 X5 I* X0 \' h& C% C
(d) Apply a light coat of Material No. 04-004* (COMMON GREASES) or Material No. 04-022* (COMMON GREASES) or Material No. 04-035* (COMMON GREASES) on the axle.
3 f( `2 q- S! O* i
$ f, J6 d ~& _5 v(e) Install the axle nut (10).
1 ~7 M- k$ w$ j, U) R( E5 E
3 w/ L& K; C6 ](f) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 21.80 m.daN (160.77 lbf.ft) with the ADAPTOR NLG (J47549) .
: J# X% @9 @9 v P. [
2 y! C* c; P* m# t8 f(g) Prevent rotation of the wheel and loosen the axle nut (10).
n9 A7 [6 w4 ]5 l
) Y8 k$ Y; ]7 d* W8 W(h) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 10.85 m.daN (80.01 lbf.ft). # d* w+ b6 i, l+ j
3 m8 ?: L% { J! v: o
(i) Tighten the axle nut (10) until the holes for the bolts (5) are aligned.
+ A9 H1 U8 r: R0 B- X4 x4 ]5 P" |" j! D" J% ~3 ^8 @
(j) Turn the wheel and make sure that the wheel is installed correctly. . D0 V" P' F% K! _6 L
) c( E/ |; _9 y5 w0 x6 ^' A
(k) Install the casing (9).
W8 G5 e( y4 U4 j" b" i6 x. J# ~! J
(l) Install the bolts (5), the washers (2) and the new IPC-CSN (32-21-13-03-070) nuts (3) .
5 w" W: {* e; T% p. P2 U+ ?( l1 i! f
(m) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in) and safety them with the new IPC-CSN (32-21-13-03-060) cotter pins (4) .
& d6 O! K- O. p" T' Z/ p8 p" X& U7 e这是前轮安装工卡 请问红色的那句话怎么翻译 谢谢。 |
|