- 注册时间
- 2011-11-30
- 最后登录
- 2011-11-30
- 在线时间
- 0 小时
- 阅读权限
- 10
- 积分
- 0
- 帖子
- 2
- 精华
- 0
- UID
- 10954
|
Installation of the wheel ! o9 U4 t" c9 Y
# ]. p0 W, Q" N' u5 V
(a) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces.
- E8 R& @* [. h0 m- i( J- m9 N/ T- b+ W0 w
(b) Install the wheel, with the valve outboard, with a handling tool.
9 \" n3 [) {2 b& `3 R% m(c) Remove the PROTECTOR NLG (J47548)
& m" Z9 |" }$ o6 h1 W) U1 v
' f6 t9 Q0 f3 Q& o* |$ s7 Q7 f+ c (d) Apply a light coat of Material No. 04-004* (COMMON GREASES) or Material No. 04-022* (COMMON GREASES) or Material No. 04-035* (COMMON GREASES) on the axle.
" Z9 u8 f* H$ d# X, Q( D! R# c- y. f0 L: ^+ |) x* W* j
(e) Install the axle nut (10).
4 m& l/ |: O- P& c% n6 D* [
6 p: n3 ?( ? G0 e0 @(f) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 21.80 m.daN (160.77 lbf.ft) with the ADAPTOR NLG (J47549) .
+ z5 f/ [! u1 V6 l3 ~; e
0 t+ o" y8 x- q' M. }+ J( M, O) M7 G(g) Prevent rotation of the wheel and loosen the axle nut (10). 4 h& R% B a% R/ n# I( `, Z. C
2 r1 g. S4 K( J(h) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 10.85 m.daN (80.01 lbf.ft). * o( p9 |/ k7 ^3 X
. C) W: B" ?* W( }(i) Tighten the axle nut (10) until the holes for the bolts (5) are aligned.
w& b b! |; |% Z1 h" Y' i. l0 }" ?. c7 p) {6 j
(j) Turn the wheel and make sure that the wheel is installed correctly. 2 t1 X! ^' _+ X) m" V. l% l) e
1 c( t0 F# M. |/ w& ~7 r
(k) Install the casing (9). ' @/ a+ {9 A' I* \3 b
% T1 b+ p9 I* t }# }6 |5 D(l) Install the bolts (5), the washers (2) and the new IPC-CSN (32-21-13-03-070) nuts (3) . 7 Y* u! Z3 _6 p1 w" }3 M; P
* ~9 Y, r+ m/ M) E9 ?4 @7 q
(m) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in) and safety them with the new IPC-CSN (32-21-13-03-060) cotter pins (4) . - v) z! f5 j) y% _* X
这是前轮安装工卡 请问红色的那句话怎么翻译 谢谢。 |
|