- 注册时间
- 2011-11-30
- 最后登录
- 2011-11-30
- 在线时间
- 0 小时
- 阅读权限
- 10
- 积分
- 0
- 帖子
- 2
- 精华
- 0
- UID
- 10954
|
Installation of the wheel 1 F% b$ [1 U" w" h
/ L8 l4 D7 s5 Y
(a) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces.
3 w" q/ ` [# Z8 u y& V8 `* j' w; G8 @" H
(b) Install the wheel, with the valve outboard, with a handling tool. 7 I0 Z( q0 ^' k& _, b: {- V4 i* P
(c) Remove the PROTECTOR NLG (J47548)
$ ^* Z1 D, p G8 j' b- C8 k) q
2 `' V( ]5 R/ b (d) Apply a light coat of Material No. 04-004* (COMMON GREASES) or Material No. 04-022* (COMMON GREASES) or Material No. 04-035* (COMMON GREASES) on the axle. , c, K% ]% d W1 G1 `0 n. ?
, j: j+ V* B; j6 o0 T! ~' t
(e) Install the axle nut (10). 3 r8 ^8 F9 S4 j; E* [
2 \' _9 [/ M' G, u6 I
(f) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 21.80 m.daN (160.77 lbf.ft) with the ADAPTOR NLG (J47549) . 3 N- ~' G ?9 {8 i: t; T# T$ u
% k4 P% J3 ^; g4 Z# a
(g) Prevent rotation of the wheel and loosen the axle nut (10). 9 R% a5 u- {2 s% |2 S/ s# a3 j
9 w* j9 k: e- z5 }) f& d(h) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 10.85 m.daN (80.01 lbf.ft). $ l) i* O2 ?' e
2 b# l [$ L* L3 `$ S2 N(i) Tighten the axle nut (10) until the holes for the bolts (5) are aligned. ! k- j5 n( @! t% L& t) P7 K
6 O) d2 f3 ]# ~' e9 t) T& k! {, k/ Z. u(j) Turn the wheel and make sure that the wheel is installed correctly.
( n: W Q5 \4 a! ~2 P6 b& x# h5 S5 W6 K# M$ }4 M/ R* y* J: J
(k) Install the casing (9). - X1 X, U c8 Y; {* y& `9 \2 u
2 h5 L! |9 F, ? O2 H& `8 p* m+ ~
(l) Install the bolts (5), the washers (2) and the new IPC-CSN (32-21-13-03-070) nuts (3) .
) i6 U2 [7 u0 B/ U- G$ s6 m0 \6 N* Q
(m) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in) and safety them with the new IPC-CSN (32-21-13-03-060) cotter pins (4) .
/ v' W0 l% k6 I9 h, H这是前轮安装工卡 请问红色的那句话怎么翻译 谢谢。 |
|