- 注册时间
- 2011-11-30
- 最后登录
- 2011-11-30
- 在线时间
- 0 小时
- 阅读权限
- 10
- 积分
- 0
- 帖子
- 2
- 精华
- 0
- UID
- 10954
|
Installation of the wheel
. r! w' n. O* \ o& Z
2 H2 K4 Q8 G- ~(a) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces.
4 r3 ~) @! D9 G# {5 H0 f; A7 a9 n& I2 `
(b) Install the wheel, with the valve outboard, with a handling tool. ' i, E/ v/ \* R. x* r. x( p5 p7 m# l) e
(c) Remove the PROTECTOR NLG (J47548)
y! r# p$ b3 N. s: |+ P! n! _" \: g! j; G4 f" H
(d) Apply a light coat of Material No. 04-004* (COMMON GREASES) or Material No. 04-022* (COMMON GREASES) or Material No. 04-035* (COMMON GREASES) on the axle. + e' q d4 i% p
) J. `3 [9 U: Y" u, `3 o3 i(e) Install the axle nut (10).
& S' V* B( a' |- U, h3 h2 R
9 J/ i/ W( R6 ?- h4 c(f) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 21.80 m.daN (160.77 lbf.ft) with the ADAPTOR NLG (J47549) .
2 d8 | ]+ Z2 K9 K
% w# O: A: ?4 L9 w) s& R) F9 t% R(g) Prevent rotation of the wheel and loosen the axle nut (10).
C0 w k* B' m# V" X3 c, R6 [
& B4 ^$ e+ }3 ]7 R/ M3 d' b% h(h) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 10.85 m.daN (80.01 lbf.ft).
6 ^4 c4 L, N' t: t3 F- s( d8 h! `1 x$ @6 W7 |9 G, V
(i) Tighten the axle nut (10) until the holes for the bolts (5) are aligned. 3 g1 |1 U N& x8 ^
8 F, k' n" f) }# {8 a
(j) Turn the wheel and make sure that the wheel is installed correctly. # D' u& m, h1 E; g7 c( c# _
: z, R1 \3 \4 v% H(k) Install the casing (9).
0 e' @/ P3 K: A' Q- L7 E
4 x3 ^2 C& v& C6 Q9 \+ e(l) Install the bolts (5), the washers (2) and the new IPC-CSN (32-21-13-03-070) nuts (3) .
6 O- o4 a- J! m( @7 R- |7 d1 }' u5 \
(m) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in) and safety them with the new IPC-CSN (32-21-13-03-060) cotter pins (4) . % A! h5 M/ G! a: m; I# g
这是前轮安装工卡 请问红色的那句话怎么翻译 谢谢。 |
|