- 注册时间
- 2008-9-13
- 最后登录
- 1970-1-1
- 在线时间
- 0 小时
- 阅读权限
- 200
- 积分
- 0
- 帖子
- 24482
- 精华
- 4
- UID
- 9
|
INTERSECTING RUNWAYS- Two or more
runways which cross or meet within their lengths.
(See INTERSECTION.)
INTERSECTIONa. A point defined by any combination of courses,
radials, or bearings of two or more navigational aids.
b. Used to describe the point where two runways,
a runway and a taxiway, or two taxiways cross or
meet.
INTERSECTION DEPARTURE- A departure from
any runway intersection except the end of the runway.
(See INTERSECTION.)
INTERSECTION TAKEOFF(See INTERSECTION DEPARTURE.)
IR(See IFR MILITARY TRAINING ROUTES.)
Pilot/Controller Glossary 2/14/08
PCG J-1
J
JAMMING- Electronic or mechanical interference
which may disrupt the display of aircraft on radar or
the transmission/reception of radio communications/
navigation.
JET BLAST- Jet engine exhaust (thrust stream
turbulence).
(See WAKE TURBULENCE.)
JET ROUTE- A route designed to serve aircraft
operations from 18,000 feet MSL up to and including
flight level 450. The routes are referred to as “J”
routes with numbering to identify the designated
route; e.g., J105.
(See Class A AIRSPACE.)
(Refer to 14 CFR Part 71.)
JET STREAM- A migrating stream of high-speed
winds present at high altitudes.
JETTISONING OF EXTERNAL STORES- Air-
borne release of external stores; e.g., tiptanks,
ordnance.
(See FUEL DUMPING.)
(Refer to 14 CFR Part 91.)
JOINT USE RESTRICTED AREA(See RESTRICTED AREA.)
Pilot/Controller Glossary 2/14/08
PCG K-1
K
KNOWN TRAFFIC- With respect to ATC clear-
ances, means aircraft whose altitude, position, and
intentions are known to ATC.
Pilot/Controller Glossary 2/14/08
PCG L-1
L
LAA(See LOCAL AIRPORT ADVISORY.)
LAAS(See LOW ALTITUDE ALERT SYSTEM.)
LAHSO- An acronym for “Land and Hold Short
Operation.” These operations include landing and
holding short of an intersecting runway, a taxiway, a
predetermined point, or an approach/departure
flightpath.
LAHSO-DRY- Land and hold short operations on
runways that are dry.
LAHSO-WET- Land and hold short operations on
runways that are wet (but not contaminated).
LAND AND HOLD SHORT OPERATIONS -
Operations which include simultaneous takeoffs and
landings and/or simultaneous landings when a
landing aircraft is able and is instructed by the
controller to hold-short of the intersecting runway/
taxiway or designated hold-short point. Pilots are
expected to promptly inform the controller if the hold
short clearance cannot be accepted.
(See PARALLEL RUNWAYS.)
(Refer to AIM.)
LANDING AREA- Any locality either on land,
water, or structures, including airports/heliports and
intermediate landing fields, which is used, or
intended to be used, for the landing and takeoff of
aircraft whether or not facilities are provided for the
shelter, servicing, or for receiving or discharging
passengers or cargo.
(See ICAO term LANDING AREA.)
LANDING AREA [ICAO]- That part of a movement
area intended for the landing or take-off of aircraft.
LANDING DIRECTION INDICATOR- A device
which visually indicates the direction in which
landings and takeoffs should be made.
(See TETRAHEDRON.)
(Refer to AIM.)
LANDING DISTANCE AVAILABLE [ICAO]- The
length of runway which is declared available and
suitable for the ground run of an aeroplane landing.
LANDING MINIMUMS- The minimum visibility
prescribed for landing a civil aircraft while using an
instrument approach procedure. The minimum
applies with other limitations set forth in 14 CFR
Part 91 with respect to the Minimum Descent
Altitude (MDA) or Decision Height (DH) prescribed
in the instrument approach procedures as follows:
a. Straight-in landing minimums. A statement of
MDA and visibility, or DH and visibility, required for
a straight-in landing on a specified runway, or
b. Circling minimums. A statement of MDA and
visibility required for the circle-to-land maneuver.
Note:_Descent below the established MDA or DH is
not authorized during an approach unless the
aircraft is in a position from which a normal
approach to the runway of intended landing can be
made and adequate visual reference to required
visual cues is maintained.
(See CIRCLE-TO-LAND MANEUVER.)
(See DECISION HEIGHT.)
(See INSTRUMENT APPROACH
PROCEDURE.)
(See MINIMUM DESCENT ALTITUDE.)
(See STRAIGHT-IN LANDING.)
(See VISIBILITY.)
(Refer to 14 CFR Part 91.)
LANDING ROLL- The distance from the point of
touchdown to the point where the aircraft can be
brought to a stop or exit the runway.
LANDING SEQUENCE- The order in which
aircraft are positioned for landing.
(See APPROACH SEQUENCE.)
LAST ASSIGNED ALTITUDE- The last altitude/
flight level assigned by ATC and acknowledged by
the pilot.
(See MAINTAIN.)
(Refer to 14 CFR Part 91.)
LATERAL NAVIGATION (LNAV)– A function of
area navigation (RNAV) equipment which calculates,
displays, and provides lateral guidance to a profile or
path.
LATERAL SEPARATION- The lateral spacing of
aircraft at the same altitude by requiring operation on
different routes or in different geographical locations.
(See SEPARATION.)
Pilot/Controller Glossary 2/14/08
PCG L-2
LDA(See LOCALIZER TYPE DIRECTIONAL AID.)
(See ICAO Term LANDING DISTANCE
AVAILABLE.)
LF(See LOW FREQUENCY.)
LIGHTED AIRPORT- An airport where runway and
obstruction lighting is available.
(See AIRPORT LIGHTING.)
(Refer to AIM.)
LIGHT GUN- A handheld directional light signaling
device which emits a brilliant narrow beam of white,
green, or red light as selected by the tower controller.
The color and type of light transmitted can be used to
approve or disapprove anticipated pilot actions where
radio communication is not available. The light gun
is used for controlling traffic operating in the vicinity
of the airport and on the airport movement area.
(Refer to AIM.)
LOCAL AIRPORT ADVISORY (LAA)- A service
provided by facilities, which are located on the
landing airport, have a discrete ground-to-air
communication frequency or the tower frequency
when the tower is closed, automated weather
reporting with voice broadcasting, and a continuous
ASOS/AWOS data display, other continuous direct
reading instruments, or manual observations avail-
able to the specialist.
(See AIRPORT ADVISORY AREA.)
LOCAL TRAFFIC- Aircraft operating in the traffic
pattern or within sight of the tower, or aircraft known
to be departing or arriving from flight in local practice
areas, or aircraft executing practice instrument
approaches at the airport.
(See TRAFFIC PATTERN.)
LOCALIZER- The component of an ILS which
provides course guidance to the runway.
(See INSTRUMENT LANDING SYSTEM.)
(See ICAO term LOCALIZER COURSE.)
(Refer to AIM.)
LOCALIZER COURSE [ICAO]- The locus of
points, in any given horizontal plane, at which the
DDM (difference in depth of modulation) is zero.
LOCALIZER OFFSET- An angular offset of the
localizer from the runway extended centerline in a
direction away from the no transgression zone (NTZ)
that increases the normal operating zone (NOZ)
width. An offset requires a 50 foot increase in DH and
is not authorized for CAT II and CAT III approaches.
LOCALIZER TYPE DIRECTIONAL AID- A
NAVAID used for nonprecision instrument ap-
proaches with utility and accuracy comparable to a
localizer but which is not a part of a complete ILS and
is not aligned with the runway.
(Refer to AIM.)
LOCALIZER USABLE DISTANCE- The maxi-
mum distance from the localizer transmitter at a
specified altitude, as verified by flight inspection, at
which reliable course information is continuously
received.
(Refer to AIM.)
LOCATOR [ICAO]- An LM/MF NDB used as an aid
to final approach.
Note:_A locator usually has an average radius of
rated coverage of between 18.5 and 46.3 km (10
and 25 NM).
LONG RANGE NAVIGATION(See LORAN.)
LONGITUDINAL SEPARATION- The longitudi-
nal spacing of aircraft at the same altitude by a
minimum distance expressed in units of time or
miles.
(See SEPARATION.)
(Refer to AIM.)
LORAN- An electronic navigational system by
which hyperbolic lines of position are determined by
measuring the difference in the time of reception of
synchronized pulse signals from two fixed transmit-
ters. Loran A operates in the 1750-1950 kHz
frequency band. Loran C and D operate in the
100-110 kHz frequency band.
(Refer to AIM.)
LOST COMMUNICATIONS- Loss of the ability to
communicate by radio. Aircraft are sometimes
referred to as NORDO (No Radio). Standard pilot
procedures are specified in 14 CFR Part 91. Radar
controllers issue procedures for pilots to follow in the
event of lost communications during a radar approach
when weather reports indicate that an aircraft will
likely encounter IFR weather conditions during the
approach.
(Refer to 14 CFR Part 91.)
(Refer AIM.)
Pilot/Controller Glossary 2/14/08
PCG L-3
LOW ALTITUDE AIRWAY STRUCTURE- The
network of airways serving aircraft operations up to
but not including 18,000 feet MSL.
(See AIRWAY.)
(Refer to AIM.)
LOW ALTITUDE ALERT, CHECK YOUR ALTI-
TUDE IMMEDIATELY(See SAFETY ALERT.)
LOW ALTITUDE ALERT SYSTEM- An auto-
mated function of the TPX-42 that alerts the
controller when a Mode C transponder equipped
aircraft on an IFR flight plan is below a
predetermined minimum safe altitude. If requested
by the pilot, Low Altitude Alert System monitoring
is also available to VFR Mode C transponder
equipped aircraft.
LOW APPROACH- An approach over an airport or
runway following an instrument approach or a VFR
approach including the go-around maneuver where
the pilot intentionally does not make contact with the
runway.
(Refer to AIM.)
LOW FREQUENCY- The frequency band between
30 and 300 kHz.
(Refer to AIM.)
LPV- A type of approach with vertical guidance
(APV) based on WAAS, published on RNAV (GPS)
approach charts. This procedure takes advantage of
the precise lateral guidance available from WAAS.
The minima is published as a decision altitude (DA).
Pilot/Controller Glossary 2/14/08
PCG M-1
M
MAA(See MAXIMUM AUTHORIZED ALTITUDE.)
MACH NUMBER- The ratio of true airspeed to the
speed of sound; e.g., MACH .82, MACH 1.6.
(See AIRSPEED.)
MACH TECHNIQUE [ICAO]- Describes a control
technique used by air traffic control whereby turbojet
aircraft operating successively along suitable routes
are cleared to maintain appropriate MACH numbers
for a relevant portion of the en route phase of flight.
The principle objective is to achieve improved
utilization of the airspace and to ensure that
separation between successive aircraft does not
decrease below the established minima.
MAHWP- Missed Approach Holding Waypoint
MAINTAINa. Concerning altitude/flight level, the term
means to remain at the altitude/flight level specified.
The phrase “climb and” or “descend and” normally
precedes “maintain” and the altitude assignment;
e.g., “descend and maintain 5,000.”
b. Concerning other ATC instructions, the term is
used in its literal sense; e.g., maintain VFR.
MAINTENANCE PLANNING FRICTION
LEVEL- The friction level specified in
AC 150/5320-12, Measurement, Construction, and
Maintenance of Skid Resistant Airport Pavement
Surfaces, which represents the friction value below
which the runway pavem ent surface rem ains
acceptable for any category or class of aircraft
operations but which is beginning to show signs of
deterioration. This value will vary depending on the
particular friction measurement equipment used.
MAKE SHORT APPROACH- Used by ATC to
inform a pilot to alter his/her traffic pattern so as to
make a short final approach.
(See TRAFFIC PATTERN.)
MAN PORTABLE AIR DEFENSE SYSTEMS
(MANPADS)- MANPADS are lightweight, shoul-
der-launched, missile systems used to bring down
aircraft and create mass casualties. The potential for
MANPADS use against airborne aircraft is real and
requires familiarity with the subject. Terrorists
choose MANPADS because the weapons are low
cost, highly mobile, require minimal set-up time, and
are easy to use and maintain. Although the weapons
have limited range, and their accuracy is affected by
poor visibility and adverse weather, they can be fired
from anywhere on land or from boats where there is
unrestricted visibility to the target.
MANDATORY ALTITUDE- An altitude depicted
on an instrum ent Approach Procedure Chart
requiring the aircraft to maintain altitude at the
depicted value.
MANPADS(See MAN PORTABLE AIR DEFENSE
SYSTEMS.)
MAP(See MISSED APPROACH POINT.)
MARKER BEACON- An electronic navigation
facility transmitting a 75 MHz vertical fan or
boneshaped radiation pattern. Marker beacons are
identified by their modulation frequency and keying
code, and when received by compatible airborne
equipment, indicate to the pilot, both aurally and
visually, that he/she is passing over the facility.
(See INNER MARKER.)
(See MIDDLE MARKER.)
(See OUTER MARKER.)
(Refer to AIM.)
MARSA(See MILITARY AUTHORITY ASSUMES
RESPONSIBILITY FOR SEPARATION OF
AIRCRAFT.)
MAWP- Missed Approach Waypoint
MAXIMUM AUTHORIZED ALTITUDE- A pub-
lished altitude representing the maximum usable
altitude or flight level for an airspace structure or
route segment. It is the highest altitude on a Federal
airway, jet route, area navigation low or high route,
or other direct route for which an MEA is designated
in 14 CFR Part 95 at which adequate reception of
navigation aid signals is assured.
MAYDAY- The international radiotelephony distress
signal. When repeated three times, it indicates
Pilot/Controller Glossary 2/14/08
PCG M-2
imminent and grave danger and that immediate
assistance is requested.
(See PAN-PAN.)
(Refer to AIM.)
MCA(See MINIMUM CROSSING ALTITUDE.)
MDA(See MINIMUM DESCENT ALTITUDE.)
MEA(See MINIMUM EN ROUTE IFR ALTITUDE.)
MEARTS(See MICRO-EN ROUTE AUTOMATED RADAR
TRACKING SYSTEM.)
METEOROLOGICAL IMPACT STATEMENT-
An unscheduled planning forecast describing
conditions expected to begin within 4 to 12 hours
which may impact the flow of air traffic in a specific
center's (ARTCC) area.
METER FIX ARC- A semicircle, equidistant from
a meter fix, usually in low altitude relatively close to
the meter fix, used to help CTAS/HOST calculate a
meter time, and determine appropriate sector meter
list assignments for aircraft not on an established
arrival route or assigned a meter fix.
METER FIX TIME/SLOT TIME- A calculated time
to depart the meter fix in order to cross the vertex at
the ACLT. This time reflects descent speed
adjustment and any applicable time that must be
absorbed prior to crossing the meter fix.
METER LIST(See ARRIVAL SECTOR ADVISORY LIST.)
METER LIST DISPLAY INTERVAL- A dynamic
parameter which controls the number of minutes
prior to the flight plan calculated time of arrival at the
meter fix for each aircraft, at which time the TCLT is
frozen and becomes an ACLT; i.e., the VTA is
updated and consequently the TCLT modified as
appropriate until frozen at which time updating is
suspended and an ACLT is assigned. When frozen,
the flight entry is inserted into the arrival sector's
meter list for display on the sector PVD/MDM.
MLDI is used if filed true airspeed is less than or
equal to freeze speed parameters (FSPD).
METERING- A method of time-regulating arrival
traffic flow into a terminal area so as not to exceed a
predetermined terminal acceptance rate.
METERING AIRPORTS- Airports adapted for
metering and for which optimum flight paths are
defined. A maximum of 15 airports may be adapted.
METERING FIX- A fix along an established route
from over which aircraft will be metered prior to
entering terminal airspace. Normally, this fix should
be established at a distance from the airport which
will facilitate a profile descent 10,000 feet above
airport elevation (AAE) or above.
METERING POSITION(S)- Adapted PVDs/
MDMs and associated “D” positions eligible for
display of a metering position list. A maximum of
four PVDs/MDMs may be adapted.
METERING POSITION LIST- An ordered list of
data on arrivals for a selected metering airport
displayed on a metering position PVD/MDM.
MFT(See METER FIX TIME/SLOT TIME.)
MHA(See MINIMUM HOLDING ALTITUDE.)
MIA(See MINIMUM IFR ALTITUDES.)
MICROBURST- A small downburst with outbursts
of damaging winds extending 2.5 miles or less. In
spite of its small horizontal scale, an intense
microburst could induce wind speeds as high as 150
knots
(Refer to AIM.)
MIC RO-EN ROUTE AUTOMATED RADAR
TRACKING SYSTEM (MEARTS)- An automated
radar and radar beacon tracking system capable of
employing both short-range (ASR) and long-range
(ARSR) radars. This microcomputer driven system
provides improved tracking, continuous data record-
ing, and use of full digital radar displays.
MICROWAVE LANDING SYSTEM- A precision
instrument approach system operating in the
microwave spectrum which normally consists of the
following components:
a. Azimuth Station.
b. Elevation Station.
c. Precision Distance Measuring Equipment.
(See MLS CATEGORIES.)
MID RVR(See VISIBILITY.)
MIDDLE COMPASS LOCATOR(See COMPASS LOCATOR.)
Pilot/Controller Glossary 2/14/08
PCG M-3
MIDDLE MARKER- A marker beacon that defines
a point along the glideslope of an ILS normally
located at or near the point of decision height (ILS
Category I). It is keyed to transmit alternate dots and
dashes, with the alternate dots and dashes keyed at the
rate of 95 dot/dash combinations per minute on a
1300 Hz tone, which is received aurally and visually
by compatible airborne equipment.
(See INSTRUMENT LANDING SYSTEM.)
(See MARKER BEACON.)
(Refer to AIM.)
MILES-IN-TRAIL- A specified distance between
aircraft, normally, in the same stratum associated
with the same destination or route of flight.
MILITARY AUTHORITY ASSUMES RESPONSI-
BILITY FOR SEPARATION OF AIRCRAFT- A
condition whereby the military services involved
assume responsibility for separation between
participating military aircraft in the ATC system. It is
used only for required IFR operations which are
specified in letters of agreement or other appropriate
FAA or military documents.
MILITARY LANDING ZONE- A landing strip used
exclusively by the military for training. A military
landing zone does not carry a runway designation.
MILITARY OPERATIONS AREA(See SPECIAL USE AIRSPACE.)
MILITARY TRAINING ROUTES- Airspace of
defined vertical and lateral dimensions established
for the conduct of military flight training at airspeeds
in excess of 250 knots IAS.
(See IFR MILITARY TRAINING ROUTES.)
(See VFR MILITARY TRAINING ROUTES.)
MINIMA(See MINIMUMS.)
MINIMUM CROSSING ALTITUDE- The lowest
altitude at certain fixes at which an aircraft must cross
when proceeding in the direction of a higher
minimum en route IFR altitude (MEA).
(See MINIMUM EN ROUTE IFR ALTITUDE.)
MINIMUM DESCENT ALTITUDE- The lowest
altitude, expressed in feet above mean sea level, to
which descent is authorized on final approach or
during circle-to-land maneuvering in execution of a
standard instrument approach procedure where no
electronic glideslope is provided.
(See NONPRECISION APPROACH
PROCEDURE.)
MINIMUM EN ROUTE IFR ALTITUDE (MEA)-
The lowest published altitude between radio fixes
which assures acceptable navigational signal cover-
age and meets obstacle clearance requirements
between those fixes. The MEA prescribed for a
Federal airway or segment thereof, area navigation
low or high route, or other direct route applies to the
entire width of the airway, segment, or route between
the radio fixes defining the airway, segment, or route.
(Refer to 14 CFR Part 91.)
(Refer to 14 CFR Part 95.)
(Refer to AIM.)
MINIMUM FRICTION LEVEL- The friction level
specified in AC 150/5320-12, Measurem ent,
Construction, and Maintenance of Skid Resistant
Airport Pavement Surfaces, that represents the
minimum recommended wet pavement surface
friction value for any turbojet aircraft engaged in
LAHSO. This value will vary with the particular
friction measurement equipment used.
MINIMUM FUEL- Indicates that an aircraft's fuel
supply has reached a state where, upon reaching the
destination, it can accept little or no delay. This is not
an emergency situation but merely indicates an
emergency situation is possible should any undue
delay occur.
(Refer to AIM.)
MINIMUM HOLDING ALTITUDE- The lowest
altitude prescribed for a holding pattern which
assures navigational signal coverage, communica-
tions, and meets obstacle clearance requirements.
MINIMUM IFR ALTITUDES (MIA)- Minimum
altitudes for IFR operations as prescribed in 14 CFR
Part 91. These altitudes are published on aeronautical
charts and prescribed in 14 CFR Part 95 for airways
and routes, and in 14 CFR Part 97 for standard
instrument approach procedures. If no applicable
minimum altitude is prescribed in 14 CFR Part 95 or
14 CFR Part 97, the following minimum IFR
altitude applies:
a. In designated mountainous areas, 2,000 feet
above the highest obstacle within a horizontal
distance of 4 nautical miles from the course to be
flown; or
Pilot/Controller Glossary 2/14/08
PCG M-4
b. Other than mountainous areas, 1,000 feet above
the highest obstacle within a horizontal distance of 4
nautical miles from the course to be flown; or
c. As otherwise authorized by the Administrator
or assigned by ATC.
(See MINIMUM CROSSING ALTITUDE.)
(See MINIMUM EN ROUTE IFR ALTITUDE.)
(See MINIMUM OBSTRUCTION CLEARANCE
ALTITUDE.)
(See MINIMUM SAFE ALTITUDE.)
(See MINIMUM VECTORING ALTITUDE.)
(Refer to 14 CFR Part 91.)
MINIMUM NAVIGATION PERFORMANCE
SPECIFICATION- A set of standards which require
aircraft to have a minimum navigation performance
capability in order to operate in MNPS designated
airspace. In addition, aircraft must be certified by
their State of Registry for MNPS operation.
MINIMUM NAVIGATION PERFORMANCE
SPECIFICATION AIRSPACE- Designated airspace
in which MNPS procedures are applied between
MNPS certified and equipped aircraft. Under certain
conditions, non-MNPS aircraft can operate in
MNPSA. However, standard oceanic separation
minima is provided between the non-MNPS aircraft
and other traffic. Currently, the only designated
MNPSA is described as follows:
a. Between FL 285 and FL 420;
b. Between latitudes 27_N and the North Pole;
c. In the east, the eastern boundaries of the CTAs
Santa Maria Oceanic, Shanwick Oceanic, and
Reykjavik;
d. In the west, the western boundaries of CTAs
Reykjavik and Gander Oceanic and New York
Oceanic excluding the area west of 60_W and south
of 38_30'N.
MINIMUM OBSTRUCTION CLEARANCE ALTI-
TUDE (MOCA)- The lowest published altitude in
effect between radio fixes on VOR airways,
off-airway routes, or route segments which meets
obstacle clearance requirements for the entire route
segment and which assures acceptable navigational
signal coverage only within 25 statute (22 nautical)
miles of a VOR.
(Refer to 14 CFR Part 91.)
(Refer to 14 CFR Part 95.)
MINIMUM RECEPTION ALTITUDE- The lowest
altitude at which an intersection can be determined.
(Refer to 14 CFR Part 95.)
MINIMUM SAFE ALTITUDEa. The minimum altitude specified in 14 CFR
Part 91 for various aircraft operations.
b. Altitudes depicted on approach charts which
provide at least 1,000 feet of obstacle clearance for
emergency use within a specified distance from the
navigation facility upon which a procedure is
predicated. These altitudes will be identified as
Minimum Sector Altitudes or Emergency Safe
Altitudes and are established as follows:
1. Minimum Sector Altitudes. Altitudes de-
picted on approach charts which provide at least
1,000 feet of obstacle clearance within a 25-mile
radius of the navigation facility upon which the
procedure is predicated. Sectors depicted on
approach charts must be at least 90 degrees in scope.
These altitudes are for emergency use only and do not
necessarily assure acceptable navigational signal
coverage.
(See ICAO term Minimum Sector Altitude.)
2. Emergency Safe Altitudes. Altitudes de-
picted on approach charts which provide at least
1,000 feet of obstacle clearance in nonmountainous
areas and 2,000 feet of obstacle clearance in
designated mountainous areas within a 100-mile
radius of the navigation facility upon which the
procedure is predicated and normally used only in
military procedures. These altitudes are identified on
published procedures as “Emergency Safe Alti-
tudes.”
MINIMUM SAFE ALTITUDE WARNING- A
function of the ARTS III computer that aids the
controller by alerting him/her when a tracked Mode
C equipped aircraft is below or is predicted by the
computer to go below a predetermined minimum safe
altitude.
(Refer to AIM.)
MINIMUM SECTOR ALTITUDE [ICAO]- The
lowest altitude which may be used under emergency
conditions which will provide a minimum clearance
of 300 m (1,000 feet) above all obstacles located in
an area contained within a sector of a circle of 46 km
(25 NM) radius centered on a radio aid to navigation.
MINIMUMS- Weather condition requirements
established for a particular operation or type of
Pilot/Controller Glossary 2/14/08
PCG M-5
operation; e.g., IFR takeoff or landing, alternate
airport for IFR flight plans, VFR flight, etc.
(See IFR CONDITIONS.)
(See IFR TAKEOFF MINIMUMS AND
DEPARTURE PROCEDURES.)
(See LANDING MINIMUMS.)
(See VFR CONDITIONS.)
(Refer to 14 CFR Part 91.)
(Refer to AIM.)
MINIMUM VECTORING ALTITUDE (MVA)-
The lowest MSL altitude at which an IFR aircraft will
be vectored by a radar controller, except as otherwise
authorized for radar approaches, departures, and
missed approaches. The altitude meets IFR obstacle
clearance criteria. It may be lower than the published
MEA along an airway or J-route segment. It may be
utilized for radar vectoring only upon the controller's
determination that an adequate radar return is being
received from the aircraft being controlled. Charts
depicting minimum vectoring altitudes are normally
available only to the controllers and not to pilots.
(Refer to AIM.)
MINUTES-IN-TRAIL- A specified interval be-
tween aircraft expressed in time. This method would
more likely be utilized regardless of altitude.
MIS(See METEOROLOGICAL IMPACT
STATEMENT.)
MISSED APPROACH-
a. A maneuver conducted by a pilot when an
instrument approach cannot be completed to a
landing. The route of flight and altitude are shown on
instrument approach procedure charts. A pilot
executing a missed approach prior to the Missed
Approach Point (MAP) must continue along the final
approach to the MAP.
b. A term used by the pilot to inform ATC that
he/she is executing the missed approach.
c. At locations where ATC radar service is
provided, the pilot should conform to radar vectors
when provided by ATC in lieu of the published
missed approach procedure.
(See MISSED APPROACH POINT.)
(Refer to AIM.)
MISSED APPROACH POINT- A point prescribed
in each instrument approach procedure at which a
missed approach procedure shall be executed if the
required visual reference does not exist.
(See MISSED APPROACH.)
(See SEGMENTS OF AN INSTRUMENT
APPROACH PROCEDURE.)
MISSED APPROACH PROCEDURE [ICAO]- The
procedure to be followed if the approach cannot be
continued.
MISSED APPROACH SEGMENT(See SEGMENTS OF AN INSTRUMENT
APPROACH PROCEDURE.)
MLDI(See METER LIST DISPLAY INTERVAL.)
MLS(See MICROWAVE LANDING SYSTEM.)
MLS CATEGORIESa. MLS Category I. An MLS approach procedure
which provides for an approach to a height above
touchdown of not less than 200 feet and a runway
visual range of not less than 1,800 feet.
b. MLS Category II. Undefined until data gather-
ing/analysis completion.
c. MLS Category III. Undefined until data
gathering/analysis completion.
MM(See MIDDLE MARKER.)
MNPS(See MINIMUM NAVIGATION PERFORMANCE
SPECIFICATION.)
MNPSA(See MINIMUM NAVIGATION PERFORMANCE-
SPECIFICATION AIRSPACE.)
MOA(See MILITARY OPERATIONS AREA.)
MOCA(See MINIMUM OBSTRUCTION CLEARANCE
ALTITUDE.)
MODE- The letter or number assigned to a specific
pulse spacing of radio signals transmitted or received
by ground interrogator or airborne transponder
components of the Air Traffic Control Radar Beacon
Pilot/Controller Glossary 2/14/08
PCG M-6
System (ATCRBS). Mode A (military Mode 3) and
Mode C (altitude reporting) are used in air traffic
control.
(See INTERROGATOR.)
(See RADAR.)
(See TRANSPONDER.)
(See ICAO term MODE.)
(Refer to AIM.)
MODE (SSR MODE) [ICAO]- The letter or number
assigned to a specific pulse spacing of the
interrogation signals transmitted by an interrogator.
There are 4 modes, A, B, C and D specified in Annex
10, corresponding to four different interrogation
pulse spacings.
MODE C INTRUDER ALERT- A function of
certain air traffic control automated systems designed
to alert radar controllers to existing or pending
situations between a tracked target (known IFR or
VFR aircraft) and an untracked target (unknown IFR
or VFR aircraft) that requires immediate attention/
action.
(See CONFLICT ALERT.)
MONITOR- (When used with communication
transfer) listen on a specific frequency and stand by
for instructions. Under normal circumstances do not
establish communications.
MONITOR ALERT (MA)- A function of the ETMS
that provides traffic management personnel with a
tool for predicting potential capacity problems in
individual operational sectors. The MA is an
indication that traffic management personnel need to
analyze a particular sector for actual activity and to
determine the required action(s), if any, needed to
control the demand.
MONITOR ALERT PARAMETER (MAP)- The
number designated for use in monitor alert
processing by the ETMS. The MAP is designated for
each operational sector for increments of 15 minutes.
MOSAIC/MULTI-SENSOR MODE- Accepts posi-
tional data from multiple radar or ADS-B sites.
Targets are displayed from a single source within a
radar sort box according to the hierarchy of the
sources assigned.
MOVEMENT AREA- The runways, taxiways, and
other areas of an airport/heliport which are utilized
for taxiing/hover taxiing, air taxiing, takeoff, and
landing of aircraft, exclusive of loading ramps and
parking areas. At those airports/heliports with a
tower, specific approval for entry onto the movement
area must be obtained from ATC.
(See ICAO term MOVEMENT AREA.)
MOVEMENT AREA [ICAO]- That part of an
aerodrome to be used for the takeoff, landing and
taxiing of aircraft, consisting of the maneuvering area
and the apron(s).
MOVING TARGET INDICATOR- An electronic
device which will permit radar scope presentation
only from targets which are in motion. A partial
remedy for ground clutter.
MRA(See MINIMUM RECEPTION ALTITUDE.)
MSA(See MINIMUM SAFE ALTITUDE.)
MSAW(See MINIMUM SAFE ALTITUDE WARNING.)
MTI(See MOVING TARGET INDICATOR.)
MTR(See MILITARY TRAINING ROUTES.)
MULTICOM- A mobile service not open to public
correspondence used to provide communications
essential to conduct the activities being performed by
or directed from private aircraft.
MULTIPLE RUNWAYS- The utilization of a
dedicated arrival runway(s) for departures and a
dedicated departure runway(s) for arrivals when
feasible to reduce delays and enhance capacity.
MVA(See MINIMUM VECTORING ALTITUDE.)
Pilot/Controller Glossary 2/14/08
PCG N-1 |
|