航空论坛_航空翻译_民航英语翻译_飞行翻译

 找回密码
 注册
搜索
查看: 3152|回复: 1
打印 上一主题 下一主题

西锐 SB 2X-27-16 SR2X 27-50 Flaps - Flap Actuator Modification [复制链接]

Rank: 9Rank: 9Rank: 9

跳转到指定楼层
1#
发表于 2011-6-18 11:44:08 |只看该作者 |倒序浏览
游客,如果您要查看本帖隐藏内容请回复
附件: 你需要登录才可以下载或查看附件。没有帐号?注册

Rank: 9Rank: 9Rank: 9

2#
发表于 2011-6-18 11:44:38 |只看该作者

CIRRUS  SR2X Service Bulletin 
Number: Issued:  SB 2X-27-16 October 02, 2009 
SNS SUBJECT: 27-50 Flaps - Flap Actuator Modification 

1.  COMPLIANCE
Recommended: Accomplish this Service Bulletin at the next scheduled maintenance, annual inspection, or within the next 12 calendar months, whichever occurs first. Compliance time begins upon receipt of this Service Bulletin.
2.  EFFECTIVITY Cirrus Design SR20 Serials 1005 thru 2029. Cirrus Design SR22 Serials 0002 thru 3459.
3.  APPROVAL
FAA approval has been obtained on all technical data in this Service Bulletin that affects type design.
4.  URPOSE
Recently, Cirrus discovered a sequential dependent condition where if the 0% flap actuator sensor fails and the actuator extends past the 0% point, the actuator rod end could bend. In the event of deploying the flaps to 100% with a bent rod end, the flaps could over-deploy and allow the flap actuator linkages to over-center. If the rod end were to fail while in this position an asymmetric flap condition could result.
To prevent this condition from occurring, this Service Bulletin installs a collar to the flap actuator to prevent the actuator from over-extending and replaces the actuator end fitting and rod end with versions of a new design. These combined changes reduce actuator travel in the event of a sensor failure.
5.  DESCRIPTION
This Service Bulletin contains instructions for the modification of the placement of the flap actuator sen-sors, replacement of the actuator end fitting and rod end, and the addition of a hard stop on the actuator shaft.
6.  WARRANTY INFORMATION
Part and labor cost for this Service Bulletin are at the owner’s expense.
7.  MANPOWER REQUIREMENTS
1.0 man-hour.
8.  OTHER PUBLICATIONS AFFECTED SR20 Airplane Maintenance Manual (p/n 12137-001) SR20 Illustrated Parts Catalog (p/n 12138-001) SR22 Airplane Maintenance Manual (p/n 13773-001) SR22 Illustrated Parts Catalog (p/n 13774-001)
9.  WEIGHT AND BALANCE
N/A
EFFECTIVITY:
SB 2X-27-16
10. MATERIAL INFORMATION
The following parts are required to comply with this Service Bulletin. Parts can be obtained from an Autho-rized Cirrus Design Service Center or Parts Distributor.
Order Kit 70231-001 to obtain the following parts:
Item No.  Description  P/N or Spec.  Supplier  Quantity 
1  End Fitting  11185-004  Cirrus Design  1 
2  Rod End, Male, RH  11315-005  Cirrus Design  1 
3  Collar, Shaft  27425-001  Cirrus Design  1 
4  Screw, Socket Head  MS21262-37  Cirrus Design  2 
5  Nut, Castellated  MS17825-4  Cirrus Design  1 
6  Cotter Pin  MS24665-132  Cirrus Design  1 

11. ACCOMPLISHMENT INSTRUCTIONS
A. Acquire necessary tools, equipment, and supplies.
Description  P/N or Spec.  Supplier  Purpose 
WS 40 Wing Template  13057-101/-102  Cirrus Design  Flap rigging. 
WS 132 Wing Template  13057-107/-108  Cirrus Design  Flap rigging. 
Inclinometer  PRO360  Macklanburg Duncan Oklahoma City, OK 73125  Deflection angle determination. 

B. Verify the flaps are in the UP position.
C. Remove key from ignition.
D. Pull FLAPS circuit breaker.
E. Remove passenger seats. (Refer to AMM 25-10)
F. Remove carpet. (Refer to AMM 25-10)
G. Remove access panels CF4C and CF5. (Refer to AMM 06-00)
H. Modify flap actuator. (See Figure 01)
CAUTION:  To prevent damage to flap hinges and flaps, tape flaps to wing prior to disconnecting actuator.
(1)  
Remove cotter pin, nut, washers, and bolt securing flap actuator to torque tube coupler. Discard nut and cotter pin and retain washers and bolt.

(2)  
Loosen jam nut securing rod end to flap actuator end fitting.

(3)  
Remove rod end fitting and remove jam nut. Discard rod end fitting and retain jam nut.

(4)  
Loosen jam nut securing flap actuator end fitting to flap actuator. Remove and discard end fitting.

(5)  
Back jam nut to bottom of flap actuator and install new end fitting (item 1) on actuator.

(6)  
Bottom out end fitting on actuator to ensure maximum thread engagement. Tighten jam nut.

(7)  
Bottom out existing jam nut onto new rod end (item 2).


EFFECTIVITY:
SB 2X-27-16
(8)  
Install rod end into actuator end fitting and bottom out. Leave jam nut loose at this time.

(9)  
Cut cable ties securing proximity sensor wiring to flap actuator.

(10)  
To facilitate flap rigging, position proximity sensors on flap actuator as follows:

(a)  
Position 0% sensor in approximate location. (See Figure 01)

(b)  
Position 50% sensor 1.0 inch (2.5 cm) from 0% sensor.

(c)  
Position 100% sensor 1.0 inch (2.5 cm) from 50% sensor.

 

(11)  
Reset FLAPS circuit breaker.

(12)  
Rotate FLAPS switch to UP position.

CAUTION:  Ensure actuator is clear of obstructions within its range of travel.

(13)  
Set MASTER SWITCH to ON position.

(14)  
Once actuator has stopped moving, set MASTER SWITCH to OFF position.

Note:  Stack-up order may be altered to allow for better alignment between flap actuator and torque tube coupler.

(15)  
Install existing bolt and washers connecting rod end to torque tube coupler and secure with new nut (item 5). Do not install cotter pin at this time.

(16)  
Remove tape securing flaps to wing.


Note:  During Adjustment/Test - Flap Travel, it is not necessary to adjust flap actuator end fitting so that flap actuator and rod end connected to torque tube coupler are installed to a depth between end fitting inspection holes. No inspection holes are drilled in new end fit-ting. Additionally, when in the 0% position, a minimum 0.05 inch (1.27 mm) clearance must be maintained between end fitting and torque tube coupler.
When adjusting position proximity sensors, it may be necessary to lengthen actuator to achieve full 0% position. Accomplish by backing out rod end, but do not exceed 2 turns maximum.
I. Perform Adjustment/Test - Flap Travel. (Refer to AMM 27-50)
J. Tighten jam nut securing rod end to actuator end fitting.
K. Torque bolt securing rod end to torque tube coupler and install new cotter pin (item 6).
L. Install cable ties securing proximity switch wiring to flap actuator.
M. Set MASTER SWITCH to ON position.
N. Reset FLAPS circuit breaker.
O. Rotate FLAPS switch to 100% position.
P. Position collar (item 3) onto shaft of actuator leaving 0.05 ±0.01 inch (1.27 ±0.25 mm) clearance between face of collar and actuator seal.
Q. Torque collar screws (item 4) to 160.0 ±5.0 in-lb (18.1 ±0.6 Nm).
R. Rotate FLAPS switch to UP position.
S. Set MASTER SWITCH to OFF position.
T. Install access panels CF4C and CF5. (Refer to AMM 06-00)
U. Install carpet. (Refer to AMM 25-10)
V. Install passenger seats. (Refer to AMM 25-10)
W. Complete airplane records by noting compliance with SB 2X-27-16 in Aircraft Logbook.
EFFECTIVITY:
SB 2X-27-16
TORQUE TUBE COUPLER (REF) 
6  PROXIMITY SENSOR (REF) 
5  7  7  4  4  3 
8  1  9  0%  50%  100% 

7  2  7  3 
NOTE Bottom out end fitting on actuator to ensure maximum thread engagement. Bottom out rod end in end fitting. During adjustment, rod end may need to be backed out a maximum of 2 turns.  SR2_SB27_1281   LEGEND 1. End Fitting 2. Rod End 3. Shaft Collar 4. Screw 5. Castellated Nut 6. Cotter Pin 7. Existing Washer 8. Existing Bolt 9. Existing Jam Nut 

Figure 01
Flap Actuator Modification (Page 1 of 2)

EFFECTIVITY:
SB 2X-27-16

TORQUE TUBE


NOTE
With flaps in 100% position, install shaft collar on actuator shaft with
0.05 ±0.01 inch (1.27 ±0.25 mm) gap between face of collar and actuator seal.
With flaps in UP position, ensure a minimum gap of 0.05 inch (1.27 mm) exists between end fitting and torque tube coupler. SR2_SB27_1282
Figure 01
Flap Actuator Modification (Page 2 of 2)

EFFECTIVITY:
SB 2X-27-16
CIRRUS  SR2X Service Bulletin 
Number: Issued:  SB 2X-27-16 October 02, 2009  Service Loop Evaluation Form 
SNS SUBJECT: 27-50 Flaps - Flap Actuator Modification 

Use this form to submit a Publications Change Request to our Engineering Department and/or to tell us what you think of the quality of this publication. We will use the data you provide us to improve the quality of our tech-nical publications.
Contact Information:
Organization: _________________________________ Today’s Date: __________________________ Address: ____________________________________ Telephone No.: _________________________ City/ST/Zip: __________________________________ Fax No: _______________________________ Prepared By: _________________________________ E-Mail: _______________________________ Title:________________________________________
Location of Publication Change Request:
Chapter Number: Section Number: Figure No (IPC or WM only): ___________________
Page Number: Page Date: Illustration Number (if applicable): _______________
Please consider the following suggestions for change:
Evaluation: 
Please rate the quality of this publication.  (good)  4  3  2 
Please rate the quality of the illustrations.  (good)  4  3  2 
Is this publication easy to understand?  (good)  4  3  2 
Is this publication easy to use?  (good)  4  3  2 
Are the Material and Accomplishment Instructions accurate? (good)  4  3  2 
Is the Manpower estimate accurate?  (good)  4  3  2 

Give the completed evaluation form to your Cirrus Field Service Representative or send this form to Cirrus Design Corporation: Manager - Technical Publications 4515 Taylor Circle Duluth, MN 55811

Cirrus Design Corp 4515 Taylor Circle Duluth, MN 55811-1548 CIRRUS DESIGN CORPORATION 4515 TAYLOR CIRCLE DULUTH, MN 55811-1548

 

 

 

 

 

 

 

 

 


 

使用道具 举报

您需要登录后才可以回帖 登录 | 注册


Archiver|航空论坛 ( 渝ICP备10008336号 )

GMT+8, 2024-11-6 00:29 , Processed in 0.026001 second(s), 12 queries .

Powered by Discuz! X2

© 2001-2011 MinHang.CC.

回顶部