- 注册时间
- 2011-11-30
- 最后登录
- 2011-11-30
- 在线时间
- 0 小时
- 阅读权限
- 10
- 积分
- 0
- 帖子
- 2
- 精华
- 0
- UID
- 10954

|
Installation of the wheel 0 T. ? r( L, t5 _0 ^6 Z
# D' ^* D6 m/ g+ a2 b(a) Clean the inner surface of the wheel bearings (surface that touches the axle). Do not apply grease on these surfaces. . Q/ f; e1 o* }8 Q9 H( ]( n7 l. K8 |5 v
% |2 @ {( ~: G& w: S8 m
(b) Install the wheel, with the valve outboard, with a handling tool.
9 C1 r9 M; w# Q/ w, J2 X(c) Remove the PROTECTOR NLG (J47548) & N7 z& j8 y/ a1 j8 S& m( D; ?
& x+ D' y/ H8 F2 y (d) Apply a light coat of Material No. 04-004* (COMMON GREASES) or Material No. 04-022* (COMMON GREASES) or Material No. 04-035* (COMMON GREASES) on the axle. - n+ o( d7 c8 Q$ U
0 L+ o g! }# C9 [: {8 i5 Q/ T
(e) Install the axle nut (10). * _' s$ q* e! f z
3 T' U& c- a& [; M1 @2 O
(f) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 21.80 m.daN (160.77 lbf.ft) with the ADAPTOR NLG (J47549) . 1 @+ l- j: Q! m+ b1 D$ I' s
# A4 \& J! K! A$ O, V( I3 z(g) Prevent rotation of the wheel and loosen the axle nut (10).
; c( ~4 x v( t4 q9 `9 p" `. R" v, G& C# ?- b# b; C
(h) Turn the wheel in the direction of the axle nut rotation and TORQUE the axle nut (10) to 10.85 m.daN (80.01 lbf.ft). / c9 e7 J8 R7 Q; f; U
2 T" ]2 ]" x0 g; r' N# w; s, A(i) Tighten the axle nut (10) until the holes for the bolts (5) are aligned.
6 {! J: \4 p/ Y& G' e W: G" a; |" A5 v7 }
(j) Turn the wheel and make sure that the wheel is installed correctly.
* Y1 g" R1 `2 v, @* m
; |8 f$ m ?# L8 `5 _( G5 i% g(k) Install the casing (9). : e* m |+ }9 F; Z/ n. D
" b0 n s5 Z' I- R' O9 ^% t( f(l) Install the bolts (5), the washers (2) and the new IPC-CSN (32-21-13-03-070) nuts (3) . 4 C9 L. i) O' J+ M+ C; D X- Z
3 m3 X) I- d- `3 E5 }. a(m) TORQUE the nuts (3) to between 0.4 and 0.45 m.daN (35.40 and 39.82 lbf.in) and safety them with the new IPC-CSN (32-21-13-03-060) cotter pins (4) .
4 b% J3 t: L ]+ \6 d! a这是前轮安装工卡 请问红色的那句话怎么翻译 谢谢。 |
|