航空论坛_航空翻译_民航英语翻译_飞行翻译

 找回密码
 注册
搜索
楼主: 帅哥
打印 上一主题 下一主题

AIM [复制链接]

Rank: 9Rank: 9Rank: 9

131#
发表于 2008-12-21 00:18:03 |只看该作者
(c) Intruder Altitude Reporting. Intruders without altitude reporting capability will be dis- played without the accompanying altitude tag. Additionally, nonaltitude reporting intruders are assumed to be at the same altitude as the TIS client for alert computations. This helps to ensure that the pilot will be alerted to all traffic under radar coverage, but the actual altitude difference may be substantial. Therefore, visual acquisition may be difficult in this instance. (d) Coverage Limitations. Since TIS is provided by ground-based, secondary surveillance radar, it is subject to all limitations of that radar. If an aircraft is not detected by the radar, it cannot be displayed on TIS. Examples of these limitations are as follows: (1) TIS will typically be provided within 55_NM of the radars depicted in FIG 4-5-5, Terminal Mode S Radar Sites. This maximum range can vary by radar site and is always subject to “line of sight” limitations; the radar and data link signals will be blocked by obstructions, terrain, and curvature of the earth. (2) TIS will be unavailable at low altitudes in many areas of the country, particularly in mountainous regions. Also, when flying near the “floor” of radar coverage in a particular area, intruders below the client aircraft may not be detected by TIS.

使用道具 举报

Rank: 9Rank: 9Rank: 9

132#
发表于 2008-12-21 00:18:09 |只看该作者
(3) TIS will be temporarily disrupted when flying directly over the radar site providing coverage if no adjacent site assumes the service. A ground-based radar, like a VOR or NDB, has a zenith cone, sometimes referred to as the cone of confusion or cone of silence. This is the area of ambiguity directly above the station where bearing information is unreliable. The zenith cone setting for TIS is 34_degrees: Any aircraft above that angle with respect to the radar horizon will lose TIS coverage from that radar until it is below this 34 degree angle. The aircraft may not actually lose service in areas of multiple radar coverage since an adjacent radar will provide TIS. If no other TIS-capable radar is available, the “Good-bye” message will be received and TIS terminated until coverage is resumed. (e) Intermittent Operations. TIS operation may be intermittent during turns or other maneuver- ing, particularly if the transponder system does not include antenna diversity (antenna mounted on the top and bottom of the aircraft). As in (d) above, TIS is dependent on two-way, “line of sight” communica- tions between the aircraft and the Mode S radar. Whenever the structure of the client aircraft comes between the transponder antenna (usually located on the underside of the aircraft) and the ground-based radar antenna, the signal may be temporarily interrupted. (f) TIS Predictive Algorithm. TIS informa- tion is collected one radar scan prior to the scan during which the uplink occurs. Therefore, the surveillance information is approximately 5 seconds old. In order to present the intruders in a “real time” position, TIS uses a “predictive algorithm” in its tracking software. This algorithm uses track history data to extrapolate intruders to their expected positions consistent with the time of display in the cockpit. Occasionally, aircraft maneuvering will cause this algorithm to induce errors in the TIS display. These errors primarily affect relative bearing information; intruder distance and altitude will remain relatively accurate and may be used to assist in “see and avoid.” Some of the more common examples of these errors are as follows:

使用道具 举报

Rank: 9Rank: 9Rank: 9

133#
发表于 2008-12-21 00:18:27 |只看该作者
(1) When client or intruder aircraft maneu- ver excessively or abruptly, the tracking algorithm will report incorrect horizontal position until the maneuvering aircraft stabilizes. (2) When a rapidly closing intruder is on a course that crosses the client at a shallow angle (either overtaking or head on) and either aircraft abruptly changes course within ¼ NM, TIS will display the intruder on the opposite side of the client than it actually is. These are relatively rare occurrences and will be corrected in a few radar scans once the course has stabilized. (g) Heading/Course Reference. Not all TIS aircraft installations will have onboard heading reference information. In these installations, aircraft course reference to the TIS display is provided by the AIM 2/14/08 4-5-14 Surveillance Systems Mode S radar. The radar only determines ground track information and has no indication of the client aircraft heading. In these installations, all intruder bearing information is referenced to ground track and does not account for wind correction. Additionally, since ground-based radar will require several scans to determine aircraft course following a course change, a lag in TIS display orientation (intruder aircraft bearing) will occur. As in (f) above, intruder distance and altitude are still usable. (h) Closely-Spaced Intruder Errors. When operating more than 30 NM from the Mode S sensor, TIS forces any intruder within 3/8 NM of the TIS client to appear at the same horizontal position as the client aircraft. Without this feature, TIS could display intruders in a manner confusing to the pilot in critical situations (e.g., a closely-spaced intruder that is actually to the right of the client may appear on the TIS display to the left). At longer distances from the radar, TIS cannot accurately determine relative bearing/distance information on intruder aircraft that are in close proximity to the client. Because TIS uses a ground-based, rotating radar for surveillance information, the accuracy of TIS data is dependent on the distance from the sensor (radar) providing the service. This is much the same phenomenon as experienced with ground-based navigational aids, such as VOR or NDB. As distance from the radar increases, the accuracy of surveillance decreases. Since TIS does not inform the pilot of distance from the Mode S radar, the pilot must assume that any intruder appearing at the same position as the client aircraft may actually be up to 3/8 NM away in any direction. Consistent with the operation of TIS, an alert on the display (regardless of distance from the radar) should stimulate an outside visual scan, intruder acquisition, and traffic avoidance based on outside reference. e. Reports of TIS Malfunctions 1. Users of TIS can render valuable assistance in the early correction of malfunctions by reporting their observations of undesirable performance. Reporters should identify the time of observation, location, type and identity of aircraft, and describe the condition observed; the type of transponder processor, and software in use can also be useful information. Since TIS performance is monitored by maintenance personnel rather than ATC, it is suggested that malfunctions be reported in the following ways: (a) By radio or telephone to the nearest Flight Service Station (FSS) facility. (b) By FAA Form 8000-7, Safety Improve- ment Report, a postage-paid card designed for this purpose. These cards may be obtained at FAA FSSs, General Aviation District Offices, Flight Standards District Offices, and General Aviation Fixed Based Operations. 4-5-7. Automatic Dependent Surveillance-Broadcast (ADS-B) Services a. Introduction 1. Automatic Dependent Surveillance-Broad- cast (ADS-B) is a surveillance technology being deployed in selected areas of the NAS (see FIG 4-5-7). ADS-B broadcasts a radio transmission approximately once per second containing the aircraft's position, velocity, identification, and other information. ADS-B can also receive reports from other suitably equipped aircraft within reception range. Additionally, these broadcasts can be received by Ground Based Transceivers (GBTs) and used to provide surveillance services, along with fleet operator monitoring of aircraft. No ground infrastruc- ture is necessary for ADS-B equipped aircraft to detect each other. 2. In the U.S., two different data links have been adopted for use with ADS-B: 1090 MHz Extended Squitter (1090 ES) and the Universal Access Transceiver (UAT). The 1090 ES link is intended for aircraft that primarily operate at FL 180 and above, whereas the UAT link is intended for use by aircraft that primarily operate at 18,000 feet and below. From a pilot's standpoint, the two links operate similarly and support ADS-B and Traffic Information Service-Broadcast (TIS-B), see paragraph 4-5-8. The UAT link additionally supports Flight Information Services-Broadcast (FIS-B), subpara- graph_7-1-11d. AIM 2/14/08 4-5-15 Surveillance Systems FIG 4-5-7 ADS-B, TIS-B, and FIS-B: Broadcast Services Architecture b. ADS-B Certification and Performance Requirements ADS-B equipment may be certified as an air-to-air system for enhancing situational awareness and as a surveillance source for air traffic services. Refer to the aircraft's flight manual supplement for the specific aircraft installation. c. ADS-B Capabilities 1. ADS-B enables improved surveillance ser- vices, both air-to-air and air-to-ground, especially in areas where radar is ineffective due to terrain or where it is impractical or cost prohibitive. Initial NAS applications of air-to-air ADS-B are for “advisory,” use only, enhancing a pilot's visual acquisition of other nearby equipped aircraft either when airborne or on the airport surface. Additionally, ADS-B will enable ATC and fleet operators to monitor aircraft throughout the available ground station coverage area. Other applications of ADS-B may include enhanced search and rescue operations and advanced air-to-air applications such as spacing, sequencing, and merging. 2. ADS-B avionics typically allow pilots to enter the aircraft's call sign and Air Traffic Control (ATC)-assigned transponder code, which will be transmitted to other aircraft and ground receivers. Pilots are cautioned to use care when selecting and entering the aircraft's identification and transponder code. Some ADS-B avionics panels are not interconnected to the transponder. Therefore, it is extremely important to ensure that the transpond- er code is identical in the ADS-B and transponder panel. Additionally, UAT systems provide a VFR “privacy” mode switch position that may be used by pilots when not wanting to receive air traffic services. This feature will broadcast a “VFR” ID to other aircraft and ground receivers, similar to the “1200” transponder code. 3. ADS-B is intended to be used in-flight and on the airport surface. ADS-B systems should be turned “on” -- and remain “on” -- whenever operating in the air and on the airport surface, thus reducing the likelihood of runway incursions. Civil and military Mode A/C transponders and ADS-B systems should be adjusted to the “on” or normal operating position as soon as practical, unless the AIM 2/14/08 4-5-16 Surveillance Systems change to “standby” has been accomplished previously at the request of ATC. Mode S transponders should be left on whenever power is applied to the aircraft. d. ATC Surveillance Services using ADS-B - Procedures and Recommended Phraseology - For_Use In Alaska Only Radar procedures, with the exceptions found in this paragraph, are identical to those procedures pre- scribed for radar in AIM Chapter 4 and Chapter 5. 1. Preflight: If a request for ATC services is predicated on ADS-B and such services are anticipated when either a VFR or IFR flight plan is filed, the aircraft's “N” number or call-sign as filed in “Block 2” of the Flight Plan shall be entered in the ADS-B avionics as the aircraft's flight ID. 2. Inflight: When requesting ADS-B services while airborne, pilots should ensure that their ADS-B equipment is transmitting their aircraft's “N” number or call sign prior to contacting ATC. To accomplish this, the pilot must select the ADS-B “broadcast flight ID” function. NOTE- The broadcast “VFR” or “Standby” mode built into some ADS-B systems will not provide ATC with the appropriate aircraft identification information. This function should first be disabled before contacting ATC. 3. Aircraft with an Inoperative/Malfunctioning ADS-B Transmitter or in the Event of an Inoperative Ground Broadcast Transceiver (GBT). (a) ATC will inform the flight crew when the aircraft's ADS-B transmitter appears to be inopera- tive or malfunctioning: PHRASEOLOGY- YOUR ADS-B TRANSMITTER APPEARS TO BE INOPERATIVE/MALFUNCTIONING. STOP ADS-B TRANSMISSIONS. (b) ATC will inform the flight crew when the GBT transceiver becomes inoperative or malfunc- tioning, as follows: PHRASEOLOGY(Name of facility) GROUND BASED TRANSCEIVER INOPERATIVE/MALFUNCTIONING. (And if appropriate) RADAR CONTACT LOST. NOTE- An inoperative or malfunctioning GBT may also cause a loss of ATC surveillance services. (c) ATC will inform the flight crew if it becomes necessary to turn off the aircraft's ADS-B transmitter. PHRASEOLOGY- STOP ADS-B TRANSMISSIONS. (d) Other malfunctions and considerations: Loss of automatic altitude reporting capabilities (encoder failure) will result in loss of ATC altitude advisory services. e. ADS-B Limitations 1. The ADS-B cockpit display of traffic is NOT intended to be used as a collision avoidance system and does not relieve the pilot's responsibility to “see and avoid” other aircraft. (See paragraph 5-5-8, See and Avoid). ADS-B shall not be used for avoidance maneuvers during IMC or other times when there is no visual contact with the intruder aircraft. ADS-B is intended only to assist in visual acquisition of other aircraft. No avoidance maneuvers are provided nor authorized, as a direct result of an ADS-B target being displayed in the cockpit. 2. Use of ADS-B radar services is limited to the service volume of the GBT. NOTE- The coverage volume of GBTs are limited to line-of-sight. f. Reports of ADS-B Malfunctions Users of ADS-B can provide valuable assistance in the correction of malfunctions by reporting instances of undesirable system performance. Reporters should identify the time of observation, location, type and identity of aircraft, and describe the condition observed; the type of avionics system and its software version in use should also be included. Since ADS-B performance is monitored by maintenance personnel rather than ATC, it is suggested that malfunctions be reported in any one of the following ways: 1. By radio or telephone to the nearest Flight Service Station (FSS) facility. 2. By FAA Form 8000-7, Safety Improvement Report, a postage-paid card is designed for this purpose. These cards may be obtained from FAA FSSs, Flight Standards District Offices, and general aviation fixed-based operators. AIM 2/14/08 4-5-17 Surveillance Systems 3. By reporting the failure directly to the FAA Safe Flight 21 program at 1-877-FLYADSB or http://www.adsb.gov. 4-5-8. Traffic Information Service-Broadcast (TIS-B) a. Introduction Traffic Information Service-Broadcast (TIS-B) is the broadcast of traffic information to ADS-B equipped aircraft from ADS-B ground stations. The source of this traffic information is derived from ground-based air traffic surveillance sensors, typically radar. TIS-B service is becoming available in selected locations where there are both adequate surveillance coverage from ground sensors and adequate broadcast coverage from Ground Based Transceivers (GBTs). The quality level of traffic information provided by TIS-B is dependent upon the number and type of ground sensors available as TIS-B sources and the timeliness of the reported data. b. TIS-B Requirements In order to receive TIS-B service, the following conditions must exist: 1. The host aircraft must be equipped with a UAT ADS-B transmitter/receiver or transceiver, and a cockpit display of traffic information (CDTI). As the ground system evolves, the ADS-B data link may be either UAT or 1090 ES, or both. 2. The host aircraft must fly within the coverage volume of a compatible GBT that is configured for TIS-B uplinks. (Not all GBTs provide TIS-B due to a lack of radar coverage or because a radar feed is not available). 3. The target aircraft must be within the coverage of, and detected by, at least one of the ATC radars serving the GBT in use. c. TIS-B Capabilities 1. TIS-B is the broadcast of traffic information to ADS-B equipped aircraft. The source of this traffic information is derived from ground-based air traffic radars. TIS-B is intended to provide ADS-B equipped aircraft with a more complete traffic picture in situations where not all nearby aircraft are equipped with ADS-B. The advisory-only applica- tion will enhance a pilot’s visual acquisition of other traffic. 2. Only transponder-equipped targets (i.e., Mode A/C or Mode S transponders) are detected. Current radar siting may result in limited radar surveillance coverage at lower altitudes near some general aviation airports, with subsequently limited TIS-B service volume coverage. If there is no radar coverage in a given area, then there will be no TIS-B coverage in that area. d. TIS-B Limitations 1. TIS-B is NOT intended to be used as a collision avoidance system and does not relieve the pilot’s responsibility to “see and avoid” other aircraft. (See paragraph 5-5-8, See and Avoid). TIS-B shall not be used for avoidance maneuvers during times when there is no visual contact with the intruder aircraft. TIS-B is intended only to assist in the visual acquisition of other aircraft. No avoidance maneuvers are provided for nor authorized as a direct result of a TIS-B target being displayed in the cockpit. 2. While TIS-B is a useful aid to visual traffic avoidance, its inherent system limitations must be understood to ensure proper use. (a) A pilot may receive an intermittent TIS-B target of themselves, typically when maneuvering (e.g., climbing turn) due to the radar not tracking the aircraft as quickly as ADS-B. (b) The ADS-B-to-radar association process within the ground system may at times have difficulty correlating an ADS-B report with corresponding radar returns from the same aircraft. When this happens the pilot will see duplicate traffic symbols (i.e., “TIS-B shadows”) on the cockpit display. (c) Updates of TIS-B traffic reports will occur less often than ADS-B traffic updates. (TIS-B position updates will occur approximately once every 3-13 seconds depending on the radar coverage. In comparison, the update rate for ADS-B is nominally once per second). (d) The TIS-B system only detects and uplinks data pertaining to transponder equipped aircraft. Aircraft without a transponder will not be displayed as a TIS-B target. AIM 2/14/4-5-18 Surveillance Systems (e) There is no indication provided when any aircraft is operating inside (or outside) the TIS-B service volume, therefore it is difficult to know if one is receiving uplinked TIS-B traffic information. Assume that not all aircraft are displayed as TIS-B targets. 3. Pilots and operators are reminded that the airborne equipment that displays TIS-B targets is for pilot situational awareness only and is not approved as a collision avoidance tool. Unless there is an imminent emergency requiring immediate action, any deviation from an air traffic control clearance based on TIS-B displayed cockpit information must be approved beforehand by the controlling ATC facility prior to commencing the maneuver. Uncoordinated deviations may place an aircraft in close proximity to other aircraft under ATC control not seen on the airborne equipment, and may result in a pilot deviation. e. Reports of TIS-B Malfunctions Users of TIS-B can provide valuable assistance in the correction of malfunctions by reporting instances of undesirable system performance. Reporters should identify the time of observation, location, type and identity of the aircraft, and describe the condition observed; the type of avionics system and its software version used. Since TIS-B performance is monitored by maintenance personnel rather than ATC, it is suggested that malfunctions be reported in anyone of the following ways: 1. By radio or telephone to the nearest Flight Service Station (FSS) facility. 2. By FAA Form 8000-7, Safety Improvement Report, a postage-paid card is designed for this purpose. These cards may be obtained from FAA FSSs, Flight Standards District Offices, and general aviation fixed-based operators. 3. By reporting the failure directly to the FAA Safe Flight 21 program at 1-877-FLYADSB or http://www.adsb.gov. 3/15/07 7110.65R CHG 2 AIM 7/31/08 AIM 2/14/08 4-6-1 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR Section 6. Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4-6-1. Applicability and RVSM Mandate (Date/Time and Area) a. Applicability. The policies, guidance and direction in this section apply to RVSM operations in the airspace over the lower 48 states, Alaska, Atlantic and Gulf of Mexico High Offshore Airspace and airspace in the San Juan FIR where VHF or UHF voice direct controller-pilot communication (DCPC) is normally available. Policies, guidance and direction for RVSM operations in oceanic airspace where VHF or UHF voice DCPC is not available and the airspace of other countries are posted on the FAA “RVSM Documentation” Webpage described in paragraph 4-6-3, Aircraft and Operator Approval Policy/Procedures, RVSM Monitoring and Databases for Aircraft and Operator Approval. b. Mandate. At 0901 UTC on January 20, 2005, the FAA implemented RVSM between flight level (FL) 290-410 (inclusive) in the following airspace: the airspace of the lower 48 states of the United States, Alaska, Atlantic and Gulf of Mexico High Offshore Airspace and the San Juan FIR. (A chart showing the location of offshore airspace is posted on the Domestic U.S. RVSM (DRVSM) Webpage. See paragraph 4-6-3.) On the same time and date, RVSM was also introduced into the adjoining airspace of Canada and Mexico to provide a seamless environment for aircraft traversing those borders. In addition, RVSM was implemented on the same date in the Caribbean and South American regions. c. RVSM Authorization. In accordance with 14 CFR Section 91.180, with only limited exceptions, prior to operating in RVSM airspace, operators and aircraft must have received RVSM authorization from the responsible civil aviation authority. (See paragraph 4-6-10, Procedures for Accommodation of Non-RVSM Aircraft.) If the operator or aircraft or both have not been authorized for RVSM operations, the aircraft will be referred to as a “non-RVSM” aircraft. Paragraph 4-6-10 discusses ATC policies for accommodation of non-RVSM aircraft flown by the Department of Defense, Air Ambulance (Lifeguard) operators, foreign State governments and aircraft flown for certification and development. Paragraph 4-6-11, Non-RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off, contains policies for non-RVSM aircraft climbing and descending through RVSM airspace to/from flight levels above RVSM airspace. d. Benefits. RVSM enhances ATC flexibility, mitigates conflict points, enhances sector throughput, reduces controller workload and enables crossing traffic. Operators gain fuel savings and operating efficiency benefits by flying at more fuel efficient flight levels and on more user preferred routings. 4-6-2. Flight Level Orientation Scheme Altitude assignments for direction of flight follow a scheme of odd altitude assignment for magnetic courses 000-179 degrees and even altitudes for magnetic courses 180-359 degrees for flights up to and including FL 410, as indicated in FIG 4-6-1. FIG 4-6-1 Flight Level Orientation Scheme NOTE- Odd Flight Levels: Magnetic Course 000-179 Degrees Even Flight Levels: Magnetic Course 180-359 Degrees. AIM 2/14/4-6-2 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4-6-3. Aircraft and Operator Approval Policy/Procedures, RVSM Monitoring and Databases for Aircraft and Operator Approval a. RVSM Authority. 14 CFR Section 91.180 applies to RVSM operations within the U.S. 14 CFR Section 91.706 applies to RVSM operations outside the U.S. Both sections require that the operator obtain authorization prior to operating in RVSM airspace. 14 CFR Section 91.180 requires that, prior to conducting RVSM operations within the U.S., the operator obtain authorization from the FAA or from the responsible authority, as appropriate. In addition, it requires that the operator and the operator’s aircraft comply with the standards of 14 CFR Part 91 Appendix G (Operations in RVSM Airspace). b. Sources of Information. The FAA RVSM Website Homepage can be accessed at: h t tp:/ /ww w.faa.gov /ab out/offic e_o r g/ headquarters_offices/ato/service_units/enroute/ rvsm/. The “RVSM Documentation” and “Domestic RVSM” webpages are linked to the RVSM Homepage. “RVSM Documentation” contains guidance and direction for an operator to obtain aircraft and operator approval to conduct RVSM operations. It provides information for DRVSM and oceanic and international RVSM airspace. It is recommended that operators planning to operate in Domestic U.S. RVSM airspace first review the following documents to orient themselves to the approval process. 1. Under “Area of Operations Specific Information,” the document, “Basic Operator Information on DRVSM Programs,” provides an overview of the DRVSM program and the related aircraft and operator approval programs. 2. In the “Getting Started” section, review the “RVSM Approval Checklist -U.S. Operators” or “RVSM Approval Checklist -Non-U.S. Operators” (as applicable). These are job aids or checklists that show aircraft/operator approval process events with references to related RVSM documents published on the website. 3. Under “Documents Applicable to All RVSM Approvals,” review “RVSM Area New to the Operator.” This document provides a guide for operators that are conducting RVSM operations in one or more areas of operation, but are planning to conduct RVSM operations in an area where they have not previously conducted RVSM operations, such as the U.S. c. TCAS Equipage. TCAS equipage requirements are contained in 14 CFR Sections 121.356, 125.224, 129.18 and 135.189. Part 91 Appendix G does not contain TCAS equipage requirements specific to RVSM, however, Appendix G does require that aircraft equipped with TCAS II and flown in RVSM airspace be modified to incorporate TCAS II Version 7.0 or a later version. d. Aircraft Monitoring. Operators are required to participate in the RVSM aircraft monitoring program. The “Monitoring Requirements and Procedures” section of the RVSM Documentation Webpage contains policies and procedures for participation in the monitoring program. Ground- based and GPS-based monitoring systems are available for the Domestic RVSM program. Monitoring is a quality control program that enables the FAA and other civil aviation authorities to assess the in-service altitude-keeping performance of aircraft and operators. e. Registration on RVSM Approvals Databases. The “Registration on RVSM Approvals Database” section of the RVSM Documentation Webpage provides policies/procedures for operator and aircraft registration on RVSM approvals databases. 1. Purpose of RVSM Approvals Databases. ATC does not use RVSM approvals databases to determine whether or not a clearance can be issued into RVSM airspace. RVSM program managers do regularly review the operators and aircraft that operate in RVSM airspace to identify and investigate those aircraft and operators flying in RVSM airspace, but not listed on the RVSM approvals databases. 2. Registration of U.S. Operators. When U.S. operators and aircraft are granted RVSM authority, the FAA Flight Standards office makes an input to the FAA Program Tracking and Reporting Subsystem (PTRS). The Separation Standards Group at the FAA Technical Center obtains PTRS operator and aircraft information to update the FAA maintained U.S. Operator/Aircraft RVSM Approvals Database. Basic database operator and aircraft information can be viewed on the RVSM Documentation Webpage by clicking on the appropriate database icon. 3/15/07 7110.65R CHG 2 AIM 7/31/08 AIM 2/14/08 4-6-3 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 3. Registration of Non-U.S. Operators. Non-U.S. operators can find policy/procedures for registration on the North American Approvals Registry and Monitoring Organization (NAARMO) database in the “Registration on RVSM Approvals Database” section of RVSM Documentation. 4-6-4. Flight Planning into RVSM Airspace a. Operators that do not file the correct aircraft equipment suffix on the FAA or ICAO Flight Plan may be denied clearance into RVSM airspace. Policies for the FAA Flight Plan are detailed in subparagraph c below. Policies for the ICAO Flight Plan are detailed in subparagraph d. b. The operator will annotate the equipment block of the FAA or ICAO Flight Plan with an aircraft equipment suffix indicating RVSM capability only after the responsible civil aviation authority has determined that both the operator and its aircraft are RVSM-compliant and has issued RVSM authoriza- tion to the operator. c. General Policies for FAA Flight Plan Equip- ment Suffix. TBL 5-1-2, Aircraft Suffixes, allows operators to indicate that the aircraft has both RVSM and Advanced Area Navigation (RNAV) capabilities or has only RVSM capability. 1. The operator will annotate the equipment block of the FAA Flight Plan with the appropriate aircraft equipment suffix from TBL 5-1-2. 2. Operators can only file one equipment suffix in block 3 of the FAA Flight Plan. Only this equipment suffix is displayed directly to the controller. 3. Aircraft with RNAV Capability. For flight in RVSM airspace, aircraft with RNAV capability, but not Advanced RNAV capability, will file “/W”. Filing “/W” will not preclude such aircraft from filing and flying direct routes in en route airspace. d. Policy for ICAO Flight Plan Equipment Suffixes. 1. Operators/aircraft that are RVSM-compliant and that file ICAO flight plans will file “/W” in block_10 (Equipment) to indicate RVSM authoriza- tion and will also file the appropriate ICAO Flight Plan suffixes to indicate navigation and communica- tion capabilities. The equipment suffixes in TBL 5-1-2 are for use only in an FAA Flight Plan (FAA_Form 7233-1). 2. Operators/aircraft that file ICAO flight plans that include flight in Domestic U.S. RVSM airspace must file “/W” in block 10 to indicate RVSM authorization. e. Importance of Flight Plan Equipment Suffixes. The operator must file the appropriate equipment suffix in the equipment block of the FAA Flight Plan (FAA Form 7233-1) or the ICAO Flight Plan. The equipment suffix informs ATC: 1. Whether or not the operator and aircraft are authorized to fly in RVSM airspace. 2. The navigation and/or transponder capability of the aircraft (e.g., advanced RNAV, transponder with Mode C). f. Significant ATC uses of the flight plan equipment suffix information are: 1. To issue or deny clearance into RVSM airspace. 2. To apply a 2,000 foot vertical separation minimum in RVSM airspace to aircraft that are not authorized for RVSM, but are in one of the limited categories that the FAA has agreed to accommodate. (See paragraphs 4-6-10, Procedures for Accom- modation of Non-RVSM Aircraft, and 4-6-11, Non-RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off, for policy on limited operation of unapproved aircraft in RVSM airspace). 3. To determine if the aircraft has “Advanced RNAV” capabilities and can be cleared to fly procedures for which that capability is required. 4-6-5. Pilot RVSM Operating Practices and Procedures a. RVSM Mandate. If either the operator or the aircraft or both have not received RVSM authoriza- tion (non-RVSM aircraft), the pilot will neither request nor accept a clearance into RVSM airspace unless: 1. The flight is conducted by a non-RVSM DOD, Lifeguard, certification/development or for- eign State (government) aircraft in accordance with paragraph 4-6-10, Procedures for Accommodation of Non-RVSM Aircraft. AIM 2/14/08 4-6-4 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 2. The pilot intends to climb to or descend from FL 430 or above in accordance with para- graph_4-6-11, Non-RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off. 3. An emergency situation exists. b. Basic RVSM Operating Practices and Procedures. Appendix 4 of Guidance 91-RVSM contains pilot practices and procedures for RVSM. Operators must incorporate Appendix 4 practices and procedures, as supplemented by the applicable paragraphs of this section, into operator training or pilot knowledge programs and operator documents containing RVSM operational policies. Guid- ance_91-RVSM is published on the RVSM Documentation Webpage under “Documents Appli- cable to All RVSM Approvals.” c. Appendix 4 contains practices and procedures for flight planning, preflight procedures at the aircraft, procedures prior to RVSM airspace entry, inflight (en route) procedures, contingency proce- dures and post flight. d. The following paragraphs either clarify or supplement Appendix 4 practices and procedures. 4-6-6. Guidance on Severe Turbulence and Mountain Wave Activity (MWA) a. Introduction/Explanation 1. The information and practices in this paragraph are provided to emphasize to pilots and controllers the importance of taking appropriate action in RVSM airspace when aircraft experience severe turbulence and/or MWA that is of sufficient magnitude to significantly affect altitude-keeping. 2. Severe Turbulence. Severe turbulence causes large, abrupt changes in altitude and/or attitude usually accompanied by large variations in indicated airspeed. Aircraft may be momentarily out of control. Encounters with severe turbulence must be remedied immediately in any phase of flight. Severe turbulence may be associated with MWA. 3. Mountain Wave Activity (MWA) (a) Significant MWA occurs both below and above the floor of RVSM airspace, FL 290. MWA often occurs in western states in the vicinity of mountain ranges. It may occur when strong winds blow perpendicular to mountain ranges resulting in up and down or wave motions in the atmosphere. Wave action can produce altitude excursions and airspeed fluctuations accompanied by only light turbulence. With sufficient amplitude, however, wave action can induce altitude and airspeed fluctuations accompanied by severe turbulence. MWA is difficult to forecast and can be highly localized and short lived. (b) Wave activity is not necessarily limited to the vicinity of mountain ranges. Pilots experiencing wave activity anywhere that significantly affects altitude-keeping can follow the guidance provided below. (c) Inflight MWA Indicators (Including Tur- bulence). Indicators that the aircraft is being subjected to MWA are: (1) Altitude excursions and/or airspeed fluctuations with or without associated turbulence. (2) Pitch and trim changes required to maintain altitude with accompanying airspeed fluctuations. (3) Light to severe turbulence depending on the magnitude of the MWA.

使用道具 举报

Rank: 9Rank: 9Rank: 9

134#
发表于 2008-12-21 00:18:40 |只看该作者
4. Priority for Controller Application of Merging Target Procedures (a) Explanation of Merging Target Proce- dures. As described in subparagraph c3 below, ATC will use “merging target procedures” to mitigate the effects of both severe turbulence and MWA. The procedures in subparagraph c3 have been adapted from existing procedures published in FAA Order_JO_7110.65, Air Traffic Control, para- graph_5-1-8, Merging Target Procedures. Paragraph_5-1-8 calls for en route controllers to advise pilots of potential traffic that they perceive may fly directly above or below his/her aircraft at minimum vertical separation. In response, pilots are given the option of requesting a radar vector to ensure their radar target will not merge or overlap with the traffic's radar target. (b) The provision of “merging target proce- dures” to mitigate the effects of severe turbulence and/or MWA is not optional for the controller, but rather is a priority responsibility. Pilot requests for vectors for traffic avoidance when encountering MWA or pilot reports of “Unable RVSM due turbulence or MWA” are considered first priority AIM 2/14/08 4-6-5 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR aircraft separation and sequencing responsibilities. (FAA Order JO 7110.65, paragraph 2-1-2, Duty Priority, states that the controller's first priority is to separate aircraft and issue safety alerts). (c) Explanation of the term “traffic permit- ting.” The contingency actions for MWA and severe turbulence detailed in paragraph 4-6-9, Contingency Actions: Weather Encounters and Aircraft System Failures, state that the controller will “vector aircraft to avoid merging targets with traffic at adjacent flight levels, traffic permitting.” The term “traffic permit- ting” is not intended to imply that merging target procedures are not a priority duty. The term is intended to recognize that, as stated in FAA Order_JO_7110.65, paragraph 2-1-2, Duty Priority, there are circumstances when the controller is required to perform more than one action and must “exercise their best judgment based on the facts and circumstances known to them” to prioritize their actions. Further direction given is: “That action which is most critical from a safety standpoint is performed first.” 5. TCAS Sensitivity. For both MWA and severe turbulence encounters in RVSM airspace, an additional concern is the sensitivity of collision avoidance systems when one or both aircraft operating in close proximity receive TCAS adviso- ries in response to disruptions in altitude hold capability. b. Pre-flight tools. Sources of observed and forecast information that can help the pilot ascertain the possibility of MWA or severe turbulence are: Forecast Winds and Temperatures Aloft (FD), Area Forecast (FA), SIGMETs and PIREPs. c. Pilot Actions When Encountering Weather (e.g., Severe Turbulence or MWA) 1. Weather Encounters Inducing Altitude Deviations of Approximately 200 feet. When the pilot experiences weather induced altitude deviations of approximately 200 feet, the pilot will contact ATC and state “Unable RVSM Due (state reason)” (e.g.,_turbulence, mountain wave). See contingency actions in paragraph 4-6-9. 2. Severe Turbulence (including that associ- ated with MWA). When pilots encounter severe turbulence, they should contact ATC and report the situation. Until the pilot reports clear of severe turbulence, the controller will apply merging target vectors to one or both passing aircraft to prevent their targets from merging: EXAMPLE“Yankee 123, FL 310, unable RVSM due severe turbulence.” “Yankee 123, fly heading 290; traffic twelve o'clock, 10_miles, opposite direction; eastbound MD-80 at FL_320” (or the controller may issue a vector to the MD-80 traffic to avoid Yankee 123). 3. MWA. When pilots encounter MWA, they should contact ATC and report the magnitude and location of the wave activity. When a controller makes a merging targets traffic call, the pilot may request a vector to avoid flying directly over or under the traffic. In situations where the pilot is experiencing altitude deviations of 200 feet or greater, the pilot will request a vector to avoid traffic. Until the pilot reports clear of MWA, the controller will apply merging target vectors to one or both passing aircraft to prevent their targets from merging: EXAMPLE“Yankee 123, FL 310, unable RVSM due mountain wave.” “Yankee 123, fly heading 290; traffic twelve o'clock, 10_miles, opposite direction; eastbound MD-80 at FL_320” (or the controller may issue a vector to the MD-80 traffic to avoid Yankee 123). 4. FL Change or Re-route. To leave airspace where MWA or severe turbulence is being encountered, the pilot may request a FL change and/or re-route, if necessary. 4-6-7. Guidance on Wake Turbulence a. Pilots should be aware of the potential for wake turbulence encounters in RVSM airspace. Experience gained since 1997 has shown that such encounters in RVSM airspace are generally moderate or less in magnitude. b. Prior to DRVSM implementation, the FAA established provisions for pilots to report wake turbulence events in RVSM airspace using the NASA Aviation Safety Reporting System (ASRS). A “Safety Reporting” section established on the FAA RVSM Documentation webpage provides contacts, forms, and reporting procedures. c. To date, wake turbulence has not been reported as a significant factor in DRVSM operations. European authorities also found that reports of wake turbulence encounters did not increase significantly AIM 2/14/08 4-6-6 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR after RVSM implementation (eight versus seven reports in a ten-month period). In addition, they found that reported wake turbulence was generally similar to moderate clear air turbulence. d. Pilot Action to Mitigate Wake Turbulence Encounters 1. Pilots should be alert for wake turbulence when operating: (a) In the vicinity of aircraft climbing or descending through their altitude. (b) Approximately 10-30 miles after passing 1,000 feet below opposite-direction traffic. (c) Approximately 10-30 miles behind and 1,000 feet below same-direction traffic. 2. Pilots encountering or anticipating wake turbulence in DRVSM airspace have the option of requesting a vector, FL change, or if capable, a lateral offset. NOTE1. Offsets of approximately a wing span upwind generally can move the aircraft out of the immediate vicinity of another aircraft's wake vortex. 2. In domestic U.S. airspace, pilots must request clearance to fly a lateral offset. Strategic lateral offsets flown in oceanic airspace do not apply. e. The FAA will track wake turbulence events as an element of its post implementation program. The FAA will advertise wake turbulence reporting procedures to the operator community and publish reporting procedures on the RVSM Documentation Webpage (See address in paragraph 4-6-3, Aircraft and Operator Approval Policy/Procedures, RVSM Monitoring and Databases for Aircraft and Operator Approval. 4-6-8. Pilot/Controller Phraseology TBL 4-6-1 shows standard phraseology that pilots and controllers will use to communicate in DRVSM operations. AIM 2/14/08 4-6-7 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR TBL 4-6-1 Pilot/Controller Phraseology Message Phraseology For a controller to ascertain the RVSM approval status of an aircraft: (call sign) confirm RVSM approved Pilot indication that flight is RVSM approved Affirm RVSM Pilot report of lack of RVSM approval (non-RVSM status). Pilot will report non-RVSM status, as follows: Negative RVSM, (supplementary information, e.g.,_“Certification flight”). a. On the initial call on any frequency in the RVSM airspace and . . .. b. In all requests for flight level changes pertaining to flight levels within the RVSM airspace and . . .. c. In all read backs to flight level clearances pertaining to flight levels within the RVSM airspace and . . .. d. In read back of flight level clearances involving climb and descent through RVSM airspace (FL 290 - 410). Pilot report of one of the following after entry into RVSM airspace: all primary altimeters, automatic altitude control systems or altitude alerters have failed. (See paragraph_4-6-9, Contingency Actions: Weather Encounters and Aircraft System Failures.) NOTE- This phrase is to be used to convey both the initial indication of RVSM aircraft system failure and on initial contact on all frequencies in RVSM airspace until the problem ceases to exist or the aircraft has exited RVSM airspace. Unable RVSM Due Equipment ATC denial of clearance into RVSM airspace Unable issue clearance into RVSM airspace, maintain FL *Pilot reporting inability to maintain cleared flight level due to weather encounter. (See paragraph 4-6-9, Contingency Actions: Weather Encounters and Aircraft System Failures). *Unable RVSM due (state reason) (e.g., turbulence, mountain wave) ATC requesting pilot to confirm that an aircraft has regained RVSM-approved status or a pilot is ready to resume RVSM Confirm able to resume RVSM Pilot ready to resume RVSM after aircraft system or weather contingency Ready to resume RVSM AIM 2/14/08 4-6-8 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 4-6-9. Contingency Actions: Weather Encounters and Aircraft System Failures TBL 4-6-2 provides pilot guidance on actions to take_under certain conditions of aircraft system failure and weather encounters. It also describes the expected ATC controller actions in these situations. It is recognized that the pilot and controller will use judgment to determine the action most appropriate to any given situation. TBL 4-6-2 Contingency Actions: Weather Encounters and Aircraft System Failures Initial Pilot Actions in Contingency Situations Initial pilot actions when unable to maintain flight level (FL) or unsure of aircraft altitude-keeping capability: _Notify ATC and request assistance as detailed below. _Maintain cleared flight level, to the extent possible, while evaluating the situation. _Watch for conflicting traffic both visually and by reference to TCAS, if equipped. _Alert nearby aircraft by illuminating exterior lights (commensurate with aircraft limitations). Severe Turbulence and/or Mountain Wave Activity (MWA) Induced Altitude Deviations of Approximately 200 feet Pilot will: Controller will: _When experiencing severe turbulence and/or MWA induced altitude deviations of approximately 200 feet or greater, pilot will contact ATC and state “Unable RVSM Due (state reason)” (e.g., turbulence, mountain wave) _If not issued by the controller, request vector clear of traffic at adjacent FLs _If desired, request FL change or re-route _Report location and magnitude of turbulence or MWA to ATC _Vector aircraft to avoid merging target with traffic at adjacent flight levels, traffic permitting _Advise pilot of conflicting traffic _Issue FL change or re-route, traffic permitting _Issue PIREP to other aircraft See paragraph 4-6-6, Guidance on Severe Turbulence and Mountain Wave Activity (MWA) for detailed guidance. Paragraph 4-6-6 explains “traffic permitting.” AIM 2/14/08 4-6-9 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR Mountain Wave Activity (MWA) Encounters - General Pilot actions: Controller actions: _Contact ATC and report experiencing MWA _If so desired, pilot may request a FL change or re-route _Report location and magnitude of MWA to ATC _Advise pilot of conflicting traffic at adjacent FL _If pilot requests, vector aircraft to avoid merging target with traffic at adjacent RVSM flight levels, traffic permitting _Issue FL change or re-route, traffic permitting _Issue PIREP to other aircraft See paragraph 4-6-6 for guidance on MWA. Paragraph 4-6-6 explains “traffic permitting.” NOTE- MWA encounters do not necessarily result in altitude deviations on the order of 200 feet. The guidance below is intended to address less significant MWA encounters. Wake Turbulence Encounters Pilot should: Controller should: _Contact ATC and request vector, FL change or, if capable, a lateral offset _Issue vector, FL change or lateral offset clearance, traffic permitting See paragraph 4-6-7, Guidance on Wake Turbulence. Paragraph 4-6-6 explains “traffic permitting.” “Unable RVSM Due Equipment” Failure of Automatic Altitude Control System, Altitude Alerter or All Primary Altimeters Pilot will: Controller will: _Contact ATC and state “Unable RVSM Due Equipment” _Request clearance out of RVSM airspace unless operational situation dictates otherwise _Provide 2,000 feet vertical separation or appropriate horizontal separation _Clear aircraft out of RVSM airspace unless operational situation dictates otherwise One Primary Altimeter Remains Operational Pilot will: Controller will: _Cross check stand-by altimeter _Notify ATC of operation with single primary altimeter _If unable to confirm primary altimeter accuracy, follow actions for failure of all primary altimeters _Acknowledge operation with single primary altimeter AIM 2/14/08 4-6-10 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR Transponder Failure Pilot will: Controller will: _Contact ATC and request authority to continue to operate at cleared flight level _Comply with revised ATC clearance, if issued _Consider request to continue to operate at cleared flight level _Issue revised clearance, if necessary NOTE14 CFR Section 91.215 (ATC transponder and altitude reporting equipment and use) regulates operation with the transponder inoperative. 4-6-10. Procedures for Accommodation of Non-RVSM Aircraft a. General Policies for Accommodation of Non-RVSM Aircraft 1. The RVSM mandate calls for only RVSM authorized aircraft/operators to fly in designated RVSM airspace with limited exceptions. The policies detailed below are intended exclusively for use by aircraft that the FAA has agreed to accommodate. They are not intended to provide other operators a means to circumvent the normal RVSM approval process. 2. If either the operator or aircraft or both have not been authorized to conduct RVSM operations, the aircraft will be referred to as a “non-RVSM” aircraft. 14 CFR Section 91.180 and Part 91 Appendix G enable the FAA to authorize a deviation to operate a non-RVSM aircraft in RVSM airspace. 3. Non-RVSM aircraft flights will be handled on a workload permitting basis. The vertical separation standard applied between aircraft not approved for RVSM and all other aircraft shall be 2,000 feet. 4. Required Pilot Calls. The pilot of non- RVSM aircraft will inform the controller of the lack of RVSM approval in accordance with the direction provided in paragraph 4-6-8, Pilot/Controller Phraseology. b. Categories of Non-RVSM Aircraft that may be Accommodated Subject to FAA approval and clearance, the following categories of non-RVSM aircraft may operate in domestic U.S. RVSM airspace provided they have an operational transponder. 1. Department of Defense (DOD) aircraft. 2. Flights conducted for aircraft certification and development purposes. 3. Active air ambulance flights utilizing a “Lifeguard” call sign. 4. Aircraft climbing/descending through RVSM flight levels (without intermediate level off) to/from FLs above RVSM airspace (Policies for these flights are detailed in paragraph 4-6-11, Non-RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off. 5. Foreign State (government) aircraft. c. Methods for operators of non-RVSM aircraft to request access to RVSM Airspace. Operators may: 1. LOA/MOU. Enter into a Letter of Agree- ment (LOA)/Memorandum of Understanding (MOU) with the RVSM facility (the Air Traffic facility that provides air traffic services in RVSM airspace). Operators must comply with LOA/MOU. AIM 2/14/08 4-6-11 Operational Policy/Procedures for Reduced Vertical Separation Minimum (RVSM) in the Domestic U.S., Alaska, Offshore Airspace and the San Juan FIR 2. File-and-Fly. File a flight plan to notify the FAA of their intention to request access to RVSM airspace. NOTE- Priority for access to RVSM airspace will be afforded to RVSM compliant aircraft, then File-and-Fly flights. 3. DOD. Some DOD non-RVSM aircraft will be designated as aircraft requiring special consider- ation. For coordination purposes they will be referred to as STORM flights. DOD enters STORM flights on the DOD Priority Mission website and notifies the departure RVSM facility for flights that are within 60_minutes of departure. NOTE- Special consideration will be afforded a STORM flight; however, accommodation of any non-RVSM flight is workload permitting. d. Center Phone Numbers. Center phone num- bers are posted on the RVSM Documentation Webpage, North American RVSM, Domestic U.S. RVSM section. This address provides direct access to the phone number listing: http://www.faa .gov /ats/ato/1 50_docs / Center_Phone_No._Non-RVSM_Acft.doc 4-6-11. Non-RVSM Aircraft Requesting Climb to and Descent from Flight Levels Above RVSM Airspace Without Intermediate Level Off a. File-and-Fly. Operators of Non-RVSM air- craft climbing to and descending from RVSM flight levels should just file a flight plan. b. Non-RVSM aircraft climbing to and descend- ing from flight levels above RVSM airspace will be handled on a workload permitting basis. The vertical separation standard applied in RVSM airspace between non-RVSM aircraft and all other aircraft shall be 2,000 feet. c. Non-RVSM aircraft climbing to/descending from RVSM airspace can only be considered for accommodation provided: 1. Aircraft is capable of a continuous climb/ descent and does not need to level off at an intermediate altitude for any operational consider- ations and 2. Aircraft is capable of climb/descent at the normal rate for the aircraft. d. Required Pilot Calls. The pilot of non-RVSM aircraft will inform the controller of the lack of RVSM approval in accordance with the direction provided in paragraph 4-6-8, Pilot/Controller Phraseology. AIM 2/14/08 5-1-1 Preflight Chapter 5. Air Traffic Procedures Section 1. Preflight 5-1-1. Preflight Preparation a. Every pilot is urged to receive a preflight briefing and to file a flight plan. This briefing should consist of the latest or most current weather, airport, and en route NAVAID information. Briefing service may be obtained from an FSS either by telephone or interphone, by radio when airborne, or by a personal visit to the station. Pilots with a current medical certificate in the 48 contiguous States may access toll-free the Direct User Access Terminal System (DUATS) through a personal computer. DUATS will provide alpha-numeric preflight weather data and allow pilots to file domestic VFR or IFR flight plans. REFERENCE- AIM, FAA Weather Services, Paragraph 7-1-2, lists DUATS vendors. NOTE- Pilots filing flight plans via “fast file” who desire to have their briefing recorded, should include a statement at the end of the recording as to the source of their weather briefing. b. The information required by the FAA to process flight plans is contained on FAA Form 7233-1, Flight Plan. The forms are available at all flight service stations. Additional copies will be provided on request. REFERENCE- AIM, Flight Plan- VFR Flights, Paragraph 5-1-4. AIM, Flight Plan- IFR Flights, Paragraph 5-1-8. c. Consult an FSS or a Weather Service Office (WSO) for preflight weather briefing. Supplemental Weather Service Locations (SWSLs) do not provide weather briefings. d. FSSs are required to advise of pertinent NOTAMs if a standard briefing is requested, but if they are overlooked, don't hesitate to remind the specialist that you have not received NOTAM information. NOTE- NOTAMs which are known in sufficient time for publication and are of 7 days duration or longer are normally incorporated into the Notices to Airmen Publication and carried there until cancellation time. FDC NOTAMs, which apply to instrument flight procedures, are also included in the Notices to Airmen Publication up to and including the number indicated in the FDC NOTAM legend. Printed NOTAMs are not provided during a briefing unless specifically requested by the pilot since the FSS specialist has no way of knowing whether the pilot has already checked the Notices to Airmen Publication prior to calling. Remember to ask for NOTAMs in the Notices to Airmen Publication. This information is not normally furnished during your briefing. REFERENCE- AIM, Notice to Airmen (NOTAM) System, Paragraph 5-1-3. e. Pilots are urged to use only the latest issue of aeronautical charts in planning and conducting flight operations. Aeronautical charts are revised and reissued on a regular scheduled basis to ensure that depicted data are current and reliable. In the conterminous U.S., Sectional Charts are updated every 6 months, IFR En Route Charts every 56 days, and amendments to civil IFR Approach Charts are accomplished on a 56-day cycle with a change notice volume issued on the 28-day midcycle. Charts that have been superseded by those of a more recent date may contain obsolete or incomplete flight information. REFERENCE- AIM, General Description of Each Chart Series, Paragraph 9-1-4. f. When requesting a preflight briefing, identify yourself as a pilot and provide the following: 1. Type of flight planned; e.g., VFR or IFR. 2. Aircraft's number or pilot's name. 3. Aircraft type. 4. Departure Airport. 5. Route of flight. 6. Destination. 7. Flight altitude(s). 8. ETD and ETE. g. Prior to conducting a briefing, briefers are required to have the background information listed above so that they may tailor the briefing to the needs of the proposed flight. The objective is to communicate a “picture” of meteorological and aeronautical information necessary for the conduct of a safe and efficient flight. Briefers use all available AIM 2/14/08 5-1-2 Preflight weather and aeronautical information to summarize data applicable to the proposed flight. They do not read weather reports and forecasts verbatim unless specifically requested by the pilot. FSS briefers do not provide FDC NOTAM information for special instrument approach procedures unless specifically asked. Pilots authorized by the FAA to use special instrument approach procedures must specifically request FDC NOTAM information for these procedures. Pilots who receive the information electronically will receive NOTAMs for special IAPs automatically. REFERENCE- AIM, Preflight Briefings, Paragraph 7-1-4, contains those items of a weather briefing that should be expected or requested. h. FAA by 14 CFR Part 93, Subpart K, has designated High Density Traffic Airports (HDTAs) and has prescribed air traffic rules and requirements for operating aircraft (excluding helicopter opera- tions) to and from these airports. REFERENCE- Airport/Facility Directory, Special Notices Section. AIM, Airport Reservation Operations and Special Traffic Management Programs, Paragraph_4-1-21. i. In addition to the filing of a flight plan, if the flight will traverse or land in one or more foreign countries, it is particularly important that pilots leave a complete itinerary with someone directly concerned and keep that person advised of the flight's progress. If serious doubt arises as to the safety of the flight, that person should first contact the FSS. REFERENCE- AIM, Flights Outside the U.S. and U.S. Territories, Paragraph 5-1-10. j. Pilots operating under provisions of 14 CFR Part_135 and not having an FAA assigned 3-letter designator, are urged to prefix the normal registration (N) number with the letter “T” on flight plan filing; e.g., TN1234B. REFERENCE- AIM, Aircraft Call Signs, Paragraph 4-2-4. 5-1-2. Follow IFR Procedures Even When Operating VFR a. To maintain IFR proficiency, pilots are urged to practice IFR procedures whenever possible, even when operating VFR. Some suggested practices include: 1. Obtain a complete preflight and weather briefing. Check the NOTAMs. 2. File a flight plan. This is an excellent low cost insurance policy. The cost is the time it takes to fill it out. The insurance includes the knowledge that someone will be looking for you if you become overdue at your destination. 3. Use current charts. 4. Use the navigation aids. Practice maintaining a good course-keep the needle centered. 5. Maintain a constant altitude which is appropriate for the direction of flight. 6. Estimate en route position times. 7. Make accurate and frequent position reports to the FSSs along your route of flight. b. Simulated IFR flight is recommended (under the hood); however, pilots are cautioned to review and adhere to the requirements specified in 14 CFR Section_91.109 before and during such flight. c. When flying VFR at night, in addition to the altitude appropriate for the direction of flight, pilots should maintain an altitude which is at or above the minimum en route altitude as shown on charts. This is especially true in mountainous terrain, where there is usually very little ground reference. Do not depend on your eyes alone to avoid rising unlighted terrain, or even lighted obstructions such as TV towers. 5-1-3. Notice to Airmen (NOTAM) System a. Time-critical aeronautical information which is of either a temporary nature or not sufficiently known in advance to permit publication on aeronautical charts or in other operational publications receives immediate dissemination via the National NOTAM System. NOTE1. NOTAM information is that aeronautical information that could affect a pilot's decision to make a flight. It includes such information as airport or primary runway closures, changes in the status of navigational aids, ILSs, radar service availability, and other information essential to planned en route, terminal, or landing operations. 2. NOTAM information is transmitted using standard contractions to reduce transmission time. See TBL 5-1-1 for a listing of the most commonly used contractions. b. NOTAM information is classified into three categories. These are NOTAM (D) or distant, NOTAM_(L) or local, and Flight Data Center (FDC) NOTAMs. AIM 2/14/08 5-1-3 Preflight 1. NOTAM (D) information is disseminated for all navigational facilities that are part of the National Airspace System (NAS), all public use airports, seaplane bases, and heliports listed in the Airport/ Facility Directory (A/FD). The complete file of all NOTAM (D) information is maintained in a computer database at the Weather Message Switching Center (WMSC), located in Atlanta, Georgia. This category of information is distributed automatically via Service A telecommunications system. Air traffic facilities, primarily FSSs, with Service A capability have access to the entire WMSC database of NOTAMs. These NOTAMs remain available via Service A for the duration of their validity or until published. Once published, the NOTAM data is deleted from the system. 2. NOTAM (L) (a) NOTAM (L) information includes such data as taxiway closures, personnel and equipment near or crossing runways, and airport lighting aids that do not affect instrument approach criteria, such as VASI. (b) NOTAM (L) information is distributed locally only and is not attached to the hourly weather reports. A separate file of local NOTAMs is maintained at each FSS for facilities in their area only. NOTAM (L) information for other FSS areas must be specifically requested directly from the FSS that has responsibility for the airport concerned. 3. FDC NOTAMs (a) On those occasions when it becomes necessary to disseminate information which is regulatory in nature, the National Flight Data Center (NFDC), in Washington, DC, will issue an FDC NOTAM. FDC NOTAMs contain such things as amendments to published IAPs and other current aeronautical charts. They are also used to advertise temporary flight restrictions caused by such things as natural disasters or large-scale public events that may generate a congestion of air traffic over a site. (b) FDC NOTAMs are transmitted via Service_A only once and are kept on file at the FSS until published or canceled. FSSs are responsible for maintaining a file of current, unpublished FDC NOTAMs concerning conditions within 400 miles of their facilities. FDC information concerning condi- tions that are more than 400 miles from the FSS, or that is already published, is given to a pilot only on request. NOTE1. DUATS vendors will provide FDC NOTAMs only upon site-specific requests using a location identifier. 2. NOTAM data may not always be current due to the changeable nature of national airspace system compo- nents, delays inherent in processing information, and occasional temporary outages of the U.S. NOTAM system. While en route, pilots should contact FSSs and obtain updated information for their route of flight and destination. c. An integral part of the NOTAM System is the Notices to Airmen Publication (NTAP) published every four weeks. Data is included in this publication to reduce congestion on the telecommunications circuits and, therefore, is not available via Service A. Once published, the information is not provided during pilot weather briefings unless specifically requested by the pilot. This publication contains two sections. 1. The first section consists of notices that meet the criteria for NOTAM (D) and are expected to remain in effect for an extended period and FDC NOTAMs that are current at the time of publication. Occasionally, some NOTAM (L) and other unique information is included in this section when it will contribute to flight safety. 2. The second section contains special notices that are either too long or concern a wide or unspecified geographic area and are not suitable for inclusion in the first section. The content of these notices vary widely and there are no specific criteria for their inclusion, other than their enhancement of flight safety. 3. The number of the last FDC NOTAM included in the publication is noted on the first page to aid the user in updating the listing with any FDC NOTAMs which may have been issued between the cut-off date and the date the publication is received. All information contained will be carried until the information expires, is canceled, or in the case of permanent conditions, is published in other publica- tions, such as the A/FD.

使用道具 举报

Rank: 9Rank: 9Rank: 9

135#
发表于 2008-12-21 00:18:53 |只看该作者
4. All new notices entered, excluding FDC NOTAMs, will be published only if the information is expected to remain in effect for at least 7 days after the effective date of the publication. AIM 2/14/08 5-1-4 Preflight d. NOTAM information is not available from a Supplemental Weather Service Locations (SWSL). TBL 5-1-1 NOTAM CONTRACTIONS A AADC . . . . . . . . Approach and Departure Control ABV . . . . . . . . . . Above A/C . . . . . . . . . . . Approach Control ACCUM . . . . . . . Accumulate ACFT . . . . . . . . . Aircraft ACR . . . . . . . . . . Air Carrier ACTV/ACTVT . Active/Activate ADF . . . . . . . . . . Automatic Direction Finder ADJ . . . . . . . . . . Adjacent ADZ/ADZD . . . . Advise/Advised AFD . . . . . . . . . . Airport/Facility Directory AFSS . . . . . . . . . Automated Flight Service Station ALS . . . . . . . . . . Approach Light System ALTM . . . . . . . . . Altimeter ALTN/ALTNLY . Alternate/Alternately ALSTG . . . . . . . . Altimeter Setting AMDT . . . . . . . . Amendment APCH . . . . . . . . . Approach APL . . . . . . . . . . Airport Lights ARFF . . . . . . . . . Aircraft Rescue & Fire Fighting ARPT . . . . . . . . . Airport ARSR . . . . . . . . . Air Route Surveillance Radar ASDE . . . . . . . . . Airport Surface Detection Equipment ASOS . . . . . . . . . Automated Surface Observing System ASPH . . . . . . . . . Asphalt ASR . . . . . . . . . . Airport Surveillance Radar ATC . . . . . . . . . . Air Traffic Control ATCT . . . . . . . . . Airport Traffic Control Tower ATIS . . . . . . . . . . Automated Terminal Information Service AVBL . . . . . . . . . Available AWOS . . . . . . . . Automatic Weather Observing System AZM . . . . . . . . . . Azimuth B BC . . . . . . . . . . . Back Course BCN . . . . . . . . . . Beacon BERM . . . . . . . . Snowbank/s Containing Earth/Gravel BLO . . . . . . . . . . Below BND . . . . . . . . . . Bound BRAF . . . . . . . . . Braking Action Fair BRAG . . . . . . . . Braking Action Good BRAN . . . . . . . . Braking Action Nil BRAP . . . . . . . . . Braking Action Poor BYD . . . . . . . . . . Beyond C CAAS . . . . . . . . . Class A Airspace CAT . . . . . . . . . . Category CBAS . . . . . . . . . Class B Airspace CBSA . . . . . . . . . Class B Surface Area CCAS . . . . . . . . . Class C Airspace CCLKWS . . . . . . Counterclockwise CCSA . . . . . . . . . Class C Surface Area CD . . . . . . . . . . . Clearance Delivery CDAS . . . . . . . . . Class D Airspace CDSA . . . . . . . . . Class D Surface Area CEAS . . . . . . . . . Class E Airspace CESA . . . . . . . . . Class E Surface Area CFA . . . . . . . . . . Controlled Firing Area CGAS . . . . . . . . . Class G Airspace CHG . . . . . . . . . . Change CLKWS . . . . . . . Clockwise CLNC . . . . . . . . . Clearance CLSD . . . . . . . . . Closed CMSN/CMSND . Commission/Commissioned CNCL/CNCLD/ CNL . . . . . . . . . . Cancel/Canceled/Cancel CNTRLN . . . . . . Centerline CONC . . . . . . . . Concrete CONT . . . . . . . . . Continue/Continuously CRS . . . . . . . . . . Course CTAF . . . . . . . . . Common Traffic Advisory Frequency CTLZ . . . . . . . . . Control Zone D DALGT . . . . . . . Daylight DCMS/DCMSND Decommission/Decommissioned DCT . . . . . . . . . . Direct DEP . . . . . . . . . . Depart/Departure DEPT . . . . . . . . . Department DH . . . . . . . . . . . Decision Height DISABLD . . . . . Disabled DLA/DLAD . . . . Delay/Delayed DLT/DLTD . . . . . Delete/Deleted DLY . . . . . . . . . . Daily DME . . . . . . . . . . Distance Measuring Equipment DMSTN . . . . . . . Demonstration DP . . . . . . . . . . . Instrument Departure Procedure DPCR . . . . . . . . . Departure Procedure DRCT . . . . . . . . . Direct DRFT/DRFTD . . Drift/Drifted Snowbank/s Caused By Wind Action DSPLCD . . . . . . Displaced DSTC . . . . . . . . . Distance DWPNT . . . . . . . Dew Point E E . . . . . . . . . . . . . East EBND . . . . . . . . . Eastbound EFAS . . . . . . . . . En Route Flight Advisory Service EFF . . . . . . . . . . . Effective ELEV . . . . . . . . . Elevate/Elevation ENG . . . . . . . . . . Engine ENTR . . . . . . . . . Entire EXCP . . . . . . . . . Except F FA . . . . . . . . . . . . Final Approach FAC . . . . . . . . . . Facility FAF . . . . . . . . . . . Final Approach Fix FDC . . . . . . . . . . Flight Data Center AIM 2/14/08 5-1-5 Preflight FM . . . . . . . . . . . Fan Marker FREQ . . . . . . . . . Frequency FRH . . . . . . . . . . Fly Runway Heading FRZN . . . . . . . . . Frozen FRNZ SLR . . . . . Frozen Slush on Runway/s FSS . . . . . . . . . . . Flight Service Station G GC . . . . . . . . . . . Ground Control GCA . . . . . . . . . . Ground Controlled Approach GOVT . . . . . . . . Government GP . . . . . . . . . . . Glide Path GPS . . . . . . . . . . Global Positioning System GRVL . . . . . . . . . Gravel GS . . . . . . . . . . . Glide Slope H HAA . . . . . . . . . . Height Above Airport HAT . . . . . . . . . . Height Above Touchdown HAZ . . . . . . . . . . Hazard HEL . . . . . . . . . . Helicopter HELI . . . . . . . . . Heliport HF . . . . . . . . . . . High Frequency HIRL . . . . . . . . . High Intensity Runway Lights HIWAS . . . . . . . . Hazardous Inflight Weather Advisory Service HOL . . . . . . . . . . Holiday HP . . . . . . . . . . . Holding Pattern I IAP . . . . . . . . . . . Instrument Approach Procedure IBND . . . . . . . . . Inbound ID . . . . . . . . . . . . Identification IDENT . . . . . . . . Identify/Identifier/Identification IFR . . . . . . . . . . . Instrument Flight Rules ILS . . . . . . . . . . . Instrument Landing System IM . . . . . . . . . . . . Inner Marker IN . . . . . . . . . . . . Inch/Inches INDEFLY . . . . . . Indefinitely INOP . . . . . . . . . Inoperative INST . . . . . . . . . . Instrument INT . . . . . . . . . . . Intersection INTST . . . . . . . . Intensity IR . . . . . . . . . . . . Ice On Runway/s L L . . . . . . . . . . . . . Left LAA . . . . . . . . . . Local Airport Advisory LAT . . . . . . . . . . Latitude LAWRS . . . . . . . Limited Aviation Weather Reporting Station LB . . . . . . . . . . . Pound/Pounds LC . . . . . . . . . . . Local Control LCL . . . . . . . . . . Local LCTD . . . . . . . . . Located LDA . . . . . . . . . . Localizer Type Directional Aid LDIN . . . . . . . . . Lead In Lighting System LGT/LGTD/ LGTS . . Light/Lighted/Lights LIRL . . . . . . . . . . Low Intensity Runway Edge Lights LLWAS . . . . . . . . Low Level Wind Shear Alert System LMM . . . . . . . . . Compass Locator at ILS Middle Marker LNDG . . . . . . . . Landing LOC . . . . . . . . . . Localizer LOM . . . . . . . . . . Compass Locator at ILS Outer Marker LONG . . . . . . . . Longitude LRN . . . . . . . . . . LORAN LSR . . . . . . . . . . Loose Snow on Runway/s LT . . . . . . . . . . . . Left Turn After Take-off M MALS . . . . . . . . Medium Intensity Approach Lighting System MALSF . . . . . . . Medium Intensity Approach Lighting System with Sequenced Flashers MALSR . . . . . . . Medium Intensity Approach Lighting System with Runway Alignment Indicator Lights MAP . . . . . . . . . . Missed Approach Point MCA . . . . . . . . . Minimum Crossing Altitude MDA . . . . . . . . . Minimum Descent Altitude MEA . . . . . . . . . . Minimum En Route Altitude MED . . . . . . . . . . Medium MIN . . . . . . . . . . Minute MIRL . . . . . . . . . Medium Intensity Runway Edge Lights MLS . . . . . . . . . . Microwave Landing System MM . . . . . . . . . . Middle Marker MNM . . . . . . . . . Minimum MOCA . . . . . . . . Minimum Obstruction Clearance Altitude MONTR . . . . . . . Monitor MSA . . . . . . . . . . Minimum Safe Altitude/Minimum Sector Altitude MSAW . . . . . . . . Minimum Safe Altitude Warning MSL . . . . . . . . . . Mean Sea Level MU . . . . . . . . . . . Designate a Friction Value Representing Runway Surface Conditions MUD . . . . . . . . . Mud MUNI . . . . . . . . . Municipal N N . . . . . . . . . . . . . North NA . . . . . . . . . . . Not Authorized NBND . . . . . . . . Northbound NDB . . . . . . . . . . Nondirectional Radio Beacon NE . . . . . . . . . . . Northeast NGT . . . . . . . . . . Night NM . . . . . . . . . . . Nautical Mile/s NMR . . . . . . . . . Nautical Mile Radius NOPT . . . . . . . . . No Procedure Turn Required NTAP . . . . . . . . . Notice To Airmen Publication NW . . . . . . . . . . . Northwest O OBSC . . . . . . . . . Obscured OBSTN . . . . . . . Obstruction OM . . . . . . . . . . . Outer Marker OPER . . . . . . . . . Operate OPN . . . . . . . . . . Operation ORIG . . . . . . . . . Original OTS . . . . . . . . . . Out of Service OVR . . . . . . . . . . Over AIM 2/14/08 5-1-6 Preflight P PAEW . . . . . . . . . Personnel and Equipment Working PAJA . . . . . . . . . Parachute Jumping Activities PAPI . . . . . . . . . . Precision Approach Path Indicator PAR . . . . . . . . . . Precision Approach Radar PARL . . . . . . . . . Parallel PAT . . . . . . . . . . . Pattern PCL . . . . . . . . . . Pilot Controlled Lighting PERM/PERMLY Permanent/Permanently PLA . . . . . . . . . . Practice Low Approach PLW . . . . . . . . . . Plow/Plowed PN . . . . . . . . . . . Prior Notice Required PPR . . . . . . . . . . Prior Permission Required PREV . . . . . . . . . Previous PRIRA . . . . . . . . Primary Radar PROC . . . . . . . . . Procedure PROP . . . . . . . . . Propeller PSGR . . . . . . . . . Passenger/s PSR . . . . . . . . . . Packed Snow on Runway/s PT/PTN . . . . . . . Procedure Turn PVT . . . . . . . . . . Private R RAIL . . . . . . . . . Runway Alignment Indicator Lights RCAG . . . . . . . . Remote Communication Air/Ground Facility RCL . . . . . . . . . . Runway Centerline RCLS . . . . . . . . . Runway Centerline Light System RCO . . . . . . . . . . Remote Communication Outlet RCV/RCVR . . . . Receive/Receiver REF . . . . . . . . . . Reference REIL . . . . . . . . . . Runway End Identifier Lights RELCTD . . . . . . Relocated RMDR . . . . . . . . Remainder RNAV . . . . . . . . . Area Navigation RPRT . . . . . . . . . Report RQRD . . . . . . . . Required RRL . . . . . . . . . . Runway Remaining Lights RSVN . . . . . . . . . Reservation RT . . . . . . . . . . . . Right Turn after Take-off RTE . . . . . . . . . . Route RTR . . . . . . . . . . Remote Transmitter/Receiver RTS . . . . . . . . . . Return to Service RUF . . . . . . . . . . Rough RVR . . . . . . . . . . Runway Visual Range RVRM . . . . . . . . RVR Midpoint RVRR . . . . . . . . . RVR Rollout RVRT . . . . . . . . . RVR Touchdown RVV . . . . . . . . . . Runway Visibility Value RY/RWY . . . . . . Runway S S . . . . . . . . . . . . . South SBND . . . . . . . . . Southbound SDF . . . . . . . . . . Simplified Directional Facility SE . . . . . . . . . . . . Southeast SECRA . . . . . . . . Secondary Radar SFL . . . . . . . . . . . Sequenced Flashing Lights SI . . . . . . . . . . . . Straight-In Approach SIR . . . . . . . . . . . Packed or Compacted Snow and Ice on Runway/s SKED . . . . . . . . . Scheduled SLR . . . . . . . . . . Slush on Runway/s SNBNK . . . . . . . Snowbank/s Caused by Plowing SND . . . . . . . . . . Sand/Sanded SNGL . . . . . . . . . Single SNW . . . . . . . . . . Snow SPD . . . . . . . . . . Speed SR . . . . . . . . . . . . Sunrise SS . . . . . . . . . . . . Sunset SSALF . . . . . . . . Simplified Short Approach Lighting System with Sequenced Flashers SSALR . . . . . . . . Simplified Short Approach Lighting System with Runway Alignment Indicator Lights SSALS . . . . . . . . Simplified Short Approach Lighting System STAR . . . . . . . . . Standard Terminal Arrival SVC . . . . . . . . . . Service SW . . . . . . . . . . . Southwest SWEPT . . . . . . . . Swept or Broom/Broomed T TACAN . . . . . . . Tactical Air Navigational Aid TDZ/TDZL . . . . . Touchdown Zone/Touchdown Zone Lights TFC . . . . . . . . . . Traffic TFR . . . . . . . . . . Temporary Flight Restriction TGL . . . . . . . . . . Touch and Go Landings THN . . . . . . . . . . Thin THR . . . . . . . . . . Threshold THRU . . . . . . . . . Through TIL . . . . . . . . . . . Until TKOF . . . . . . . . . Takeoff TMPRY . . . . . . . Temporary TRML . . . . . . . . Terminal TRNG . . . . . . . . . Training TRSA . . . . . . . . . Terminal Radar Service Area TRSN . . . . . . . . . Transition TSNT . . . . . . . . . Transient TWEB . . . . . . . . Transcribed Weather Broadcast TWR . . . . . . . . . . Tower TWY . . . . . . . . . Taxiway U UNAVBL . . . . . . Unavailable UNLGTD . . . . . . Unlighted UNMKD . . . . . . Unmarked UNMON . . . . . . Unmonitored UNRELBL . . . . . Unreliable UNUSBL . . . . . . Unusable V VASI . . . . . . . . . . Visual Approach Slope Indicator VDP . . . . . . . . . . Visual Descent Point VFR . . . . . . . . . . Visual Flight Rules VIA . . . . . . . . . . By Way Of VICE . . . . . . . . . Instead/Versus VIS/VSBY . . . . . Visibility AIM 2/14/08 5-1-7 Preflight VMC . . . . . . . . . Visual Meteorological Conditions VOL . . . . . . . . . . Volume VOLMET . . . . . . Meteorlogical Information for Aircraft in Flight VOR . . . . . . . . . . VHF Omni-Directional Radio Range VORTAC . . . . . . VOR and TACAN (collocated) VOT . . . . . . . . . . VOR Test Signal W W . . . . . . . . . . . . West WBND . . . . . . . . Westbound WEA/WX . . . . . . Weather WI . . . . . . . . . . . Within WKDAYS . . . . . Monday through Friday WKEND . . . . . . . Saturday and Sunday WND . . . . . . . . . Wind WP . . . . . . . . . . . Waypoint WSR . . . . . . . . . . Wet Snow on Runway/s WTR . . . . . . . . . . Water on Runway/s WX . . . . . . . . . . . Weather / . . . . . . . . . . . . . And + . . . . . . . . . . . . . In Addition/Also 5-1-4. Flight Plan - VFR Flights a. Except for operations in or penetrating a Coastal or Domestic ADIZ or DEWIZ a flight plan is not required for VFR flight. REFERENCE- AIM, National Security, Paragraph 5-6-1. b. It is strongly recommended that a flight plan (for a VFR flight) be filed with an FAA FSS. This will ensure that you receive VFR Search and Rescue Protection. REFERENCE- AIM, Search and Rescue, Paragraph 6-2-7 gives the proper method of filing a VFR flight plan. c. To obtain maximum benefits from the flight plan program, flight plans should be filed directly with the nearest FSS. For your convenience, FSSs provide aeronautical and meteorological briefings while accepting flight plans. Radio may be used to file if no other means are available. NOTE- Some states operate aeronautical communications facili- ties which will accept and forward flight plans to the FSS for further handling. d. When a “stopover” flight is anticipated, it is recommended that a separate flight plan be filed for each “leg” when the stop is expected to be more than 1 hour duration. e. Pilots are encouraged to give their departure times directly to the FSS serving the departure airport or as otherwise indicated by the FSS when the flight plan is filed. This will ensure more efficient flight plan service and permit the FSS to advise you of significant changes in aeronautical facilities or meteorological conditions. When a VFR flight plan is filed, it will be held by the FSS until 1 hour after the proposed departure time unless: 1. The actual departure time is received. 2. A revised proposed departure time is received. 3. At a time of filing, the FSS is informed that the proposed departure time will be met, but actual time cannot be given because of inadequate communications (assumed departures). f. On pilot's request, at a location having an active tower, the aircraft identification will be forwarded by the tower to the FSS for reporting the actual departure time. This procedure should be avoided at busy airports. g. Although position reports are not required for VFR flight plans, periodic reports to FAA FSSs along the route are good practice. Such contacts permit significant information to be passed to the transiting aircraft and also serve to check the progress of the flight should it be necessary for any reason to locate the aircraft. EXAMPLE1. Bonanza 314K, over Kingfisher at (time), VFR flight plan, Tulsa to Amarillo. 2. Cherokee 5133J, over Oklahoma City at (time), Shreveport to Denver, no flight plan. h. Pilots not operating on an IFR flight plan and when in level cruising flight, are cautioned to conform with VFR cruising altitudes appropriate to the direction of flight. i. When filing VFR flight plans, indicate aircraft equipment capabilities by appending the appropriate suffix to aircraft type in the same manner as that prescribed for IFR flight. REFERENCE- AIM, Flight Plan- IFR Flights, Paragraph 5-1-8. j. Under some circumstances, ATC computer tapes can be useful in constructing the radar history of a downed or crashed aircraft. In each case, knowledge of the aircraft's transponder equipment is necessary in determining whether or not such computer tapes might prove effective. AIM 2/14/08 5-1-8 Preflight FIG 5-1-1 FAA Flight Plan Form 7233-1 (8-82) U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION (FAA USE ONLY) PILOT BRIEFING VNR STOPOVER TIME STARTED SPECIALIST INITIALS 1. TYPE VFR IFR DVFR TYPE/ EQUIPMENT 3. AIRCRAFT SPECIAL 5. DEPARTURE POINT 6. DEPARTURE TIME (Z) PROPOSED ACTUAL (Z) 7. CRUISING ALTITUDE 8. ROUTE OF FLIGHT KTS DESTINATION Name of airport 9. (and city) 10. EST. TIME ENROUTE HOURS HOURS MINUTES MINUTES 11. REMARKS 12. FUEL ON BOARD ALTERNATE 13. AIRPORT(S) 14. PILOT'S NAME, ADDRESS & TELEPHONE NUMBER & AIRCRAFT HOME BASE ABOARD 15. NUMBER 17. DESTINATION CONTACT/TELEPHONE (OPTIONAL) COLOR AIRCRAFT 16. OF FAA Form 7233-1 (8-82) CLOSE VFR FLIGHT PLAN WITH _________________ FSS ON ARRIVAL FLIGHT PLAN CIVIL AIRCRAFT PILOTS, FAR 91 requires you file an IFR flight plan to operate under instrument flight rules in controlled airspace. Failure to file could result in a civil penalty not to exceed 1,000 for each violation (Section 901 of the Federal Aviation Act of 1958, as amended). Filing of a VFR flight plan is recommended as a good operating practice. See also Part 99 for requirements concerning DVFR flight plans. AIRCRAFT IDENTIFICATION 2. 4. TRUE AIRSPEED k. Flight Plan Form - (See FIG 5-1-1). l. Explanation of VFR Flight Plan Items. 1. Block 1. Check the type flight plan. Check both the VFR and IFR blocks if composite VFR/IFR. 2. Block 2. Enter your complete aircraft identification including the prefix “N” if applicable. 3. Block 3. Enter the designator for the aircraft, or if unknown, consult an FSS briefer. 4. Block 4. Enter your true airspeed (TAS). 5. Block 5. Enter the departure airport identifi- er code, or if unknown, the name of the airport. 6. Block 6. Enter the proposed departure time in Coordinated Universal Time (UTC) (Z). If airborne, specify the actual or proposed departure time as appropriate. 7. Block 7. Enter the appropriate VFR altitude (to assist the briefer in providing weather and wind information). 8. Block 8. Define the route of flight by using NAVAID identifier codes and airways. 9. Block 9. Enter the destination airport identifier code, or if unknown, the airport name. NOTE- Include the city name (or even the state name) if needed for clarity. 10. Block 10. Enter your estimated time en_route in hours and minutes. 11. Block 11. Enter only those remarks perti- nent to ATC or to the clarification of other flight plan information, such as the appropriate radiotelephony (call sign) associated with the designator filed in Block 2. Items of a personal nature are not accepted. 12. Block 12. Specify the fuel on board in hours and minutes. 13. Block 13. Specify an alternate airport if desired. 14. Block 14. Enter your complete name, address, and telephone number. Enter sufficient AIM 2/14/08 5-1-9 Preflight information to identify home base, airport, or operator. NOTE- This information is essential in the event of search and rescue operations. 15. Block 15. Enter total number of persons on board (POB) including crew. 16. Block 16. Enter the predominant colors. 17. Block 17. Record the FSS name for closing the flight plan. If the flight plan is closed with a different FSS or facility, state the recorded FSS name that would normally have closed your flight plan. NOTE1. Optional- record a destination telephone number to assist search and rescue contact should you fail to report or cancel your flight plan within 1/2 hour after your estimated time of arrival (ETA). 2. The information transmitted to the destination FSS will consist only of flight plan blocks 2, 3, 9, and 10. Estimated time en route (ETE) will be converted to the correct ETA. 5-1-5. Operational Information System (OIS) a. The FAA's Air Traffic Control System Command Center (ATCSCC) maintains a web site with near real-time National Airspace System (NAS) status information. NAS operators are encouraged to access the web site at http://www.fly.faa.gov prior to filing their flight plan. b. The web site consolidates information from advisories. An advisory is a message that is disseminated electronically by the ATCSCC that contains information pertinent to the NAS. 1. Advisories are normally issued for the following items: (a) Ground Stops. (b) Ground Delay Programs. (c) Route Information. (d) Plan of Operations. (e) Facility Outages and Scheduled Facility Outages. (f) Volcanic Ash Activity Bulletins. (g) Special Traffic Management Programs. 2. This list is not all-inclusive. Any time there is information that may be beneficial to a large number of people, an advisory may be sent. Additionally, there may be times when an advisory is not sent due to workload or the short length of time of the activity. 3. Route information is available on the web site and in specific advisories. Some route information, subject to the 56-day publishing cycle, is located on the “OIS” under “Products,” Route Management Tool (RMT), and “What's New” Playbook. The RMT and Playbook contain routings for use by Air Traffic and NAS operators when they are coordinated “real-time” and are then published in an ATCSCC advisory. 4. Route advisories are identified by the word “Route” in the header; the associated action is required (RQD), recommended (RMD), planned (PLN), or for your information (FYI). Operators are expected to file flight plans consistent with the Route RQD advisories. 5-1-6. Flight Plan- Defense VFR (DVFR) Flights VFR flights into a Coastal or Domestic ADIZ/ DEWIZ are required to file DVFR flight plans for security purposes. Detailed ADIZ procedures are found in Section 6, National Security and Intercep- tion Procedures, of this chapter. (See 14 CFR Part_99.) 5-1-7. Composite Flight Plan (VFR/IFR Flights) a. Flight plans which specify VFR operation for one portion of a flight, and IFR for another portion, will be accepted by the FSS at the point of departure. If VFR flight is conducted for the first portion of the flight, pilots should report their departure time to the FSS with whom the VFR/IFR flight plan was filed; and, subsequently, close the VFR portion and request ATC clearance from the FSS nearest the point at which change from VFR to IFR is proposed. Regardless of the type facility you are communicat- ing with (FSS, center, or tower), it is the pilot's responsibility to request that facility to “CLOSE VFR FLIGHT PLAN.” The pilot must remain in VFR weather conditions until operating in accordance with the IFR clearance. AIM 2/14/08 5-1-10 Preflight b. When a flight plan indicates IFR for the first portion of flight and VFR for the latter portion, the pilot will normally be cleared to the point at which the change is proposed. After reporting over the clearance limit and not desiring further IFR clearance, the pilot should advise ATC to cancel the IFR portion of the flight plan. Then, the pilot should contact the nearest FSS to activate the VFR portion of the flight plan. If the pilot desires to continue the IFR flight plan beyond the clearance limit, the pilot should contact ATC at least 5 minutes prior to the clearance limit and request further IFR clearance. If the requested clearance is not received prior to reaching the clearance limit fix, the pilot will be expected to enter into a standard holding pattern on the radial or course to the fix unless a holding pattern for the clearance limit fix is depicted on a U.S. Government or commercially produced (meeting FAA require- ments) low or high altitude enroute, area or STAR chart. In this case the pilot will hold according to the depicted pattern. 5-1-8. Flight Plan- IFR Flights a. General 1. Prior to departure from within, or prior to entering controlled airspace, a pilot must submit a complete flight plan and receive an air traffic clearance, if weather conditions are below VFR minimums. Instrument flight plans may be submitted to the nearest FSS or ATCT either in person or by telephone (or by radio if no other means are available). Pilots should file IFR flight plans at least 30 minutes prior to estimated time of departure to preclude possible delay in receiving a departure clearance from ATC. In order to provide FAA traffic management units strategic route planning capabili- ties, nonscheduled operators conducting IFR operations above FL 230 are requested to voluntarily file IFR flight plans at least 4 hours prior to estimated time of departure (ETD). To minimize your delay in entering Class B, Class C, Class D, and Class E surface areas at destination when IFR weather conditions exist or are forecast at that airport, an IFR flight plan should be filed before departure. Otherwise, a 30 minute delay is not unusual in receiving an ATC clearance because of time spent in processing flight plan data. Traffic saturation frequently prevents control personnel from accepting flight plans by radio. In such cases, the pilot is advised to contact the nearest FSS for the purpose of filing the flight plan. NOTE- There are several methods of obtaining IFR clearances at nontower, non-FSS, and outlying airports. The procedure may vary due to geographical features, weather conditions, and the complexity of the ATC system. To determine the most effective means of receiving an IFR clearance, pilots should ask the nearest FSS the most appropriate means of obtaining the IFR clearance. 2. When filing an IFR flight plan, include as a prefix to the aircraft type, the number of aircraft when more than one and/or heavy aircraft indicator “H/” if appropriate. EXAMPLE- H/DC10/A 2/F15/A 3. When filing an IFR flight plan, identify the equipment capability by adding a suffix, preceded by a slant, to the AIRCRAFT TYPE, as shown in TBL 5-1-2, Aircraft Suffixes. NOTE1. ATC issues clearances based on filed suffixes. Pilots should determine the appropriate suffix based upon desired services and/or routing. For example, if a desired route/procedure requires GPS, a pilot should file /G even if the aircraft also qualifies for other suffixes. 2. For procedures requiring GPS, if the navigation system does not automatically alert the flight crew of a loss of GPS, the operator must develop procedures to verify correct GPS operation. 3. The suffix is not to be added to the aircraft identification or be transmitted by radio as part of the aircraft identification. 4. It is recommended that pilots file the maximum transponder or navigation capability of their aircraft in the equipment suffix. This will provide ATC with the necessary information to utilize all facets of navigational equipment and transponder capabilities available. AIM 2/14/08 5-1-11 Preflight TBL 5-1-2 Aircraft Suffixes Suffix Equipment Capability NO DME /X No transponder /T Transponder with no Mode C /U Transponder with Mode C DME /D No transponder /B Transponder with no Mode C /A Transponder with Mode C TACAN ONLY /M No transponder /N Transponder with no Mode C /P Transponder with Mode C AREA NAVIGATION (RNAV) /Y LORAN, VOR/DME, or INS with no transponder /C LORAN, VOR/DME, or INS, transponder with no Mode C /I LORAN, VOR/DME, or INS, transponder with Mode C ADVANCED RNAV WITH TRANSPONDER AND MODE C (If an aircraft is unable to operate with a transponder and/or Mode C, it will revert to the appropriate code listed above under Area Navigation.) /E Flight Management System (FMS) with DME/DME and IRU position updating /F FMS with DME/DME position updating /G Global Navigation Satellite System (GNSS), including GPS or Wide Area Augmentation System (WAAS), with en_route and terminal capability. /R Required Navigational Performance (RNP). The aircraft meets the RNP type prescribed for the route segment(s), route(s) and/or area concerned. Reduced Vertical Separation Minimum (RVSM). Prior to conducting RVSM operations within the U.S., the operator must obtain authorization from the FAA or from the responsible authority, as appropriate. /J /E with RVSM /K /F with RVSM /L /G with RVSM /Q /R with RVSM /W RVSM AIM 2/14/08 5-1-12 Preflight b. Airways and Jet Routes Depiction on Flight Plan 1. It is vitally important that the route of flight be accurately and completely described in the flight plan. To simplify definition of the proposed route, and to facilitate ATC, pilots are requested to file via airways or jet routes established for use at the altitude or flight level planned. 2. If flight is to be conducted via designated airways or jet routes, describe the route by indicating the type and number designators of the airway(s) or jet route(s) requested. If more than one airway or jet route is to be used, clearly indicate points of transition. If the transition is made at an unnamed intersection, show the next succeeding NAVAID or named intersection on the intended route and the complete route from that point. Reporting points may be identified by using authorized name/code as depicted on appropriate aeronautical charts. The following two examples illustrate the need to specify the transition point when two routes share more than one transition fix. EXAMPLE1. ALB J37 BUMPY J14 BHM Spelled out: from Albany, New York, via Jet Route 37 transitioning to Jet Route 14 at BUMPY intersection, thence via Jet Route 14 to Birmingham, Alabama. 2. ALB J37 ENO J14 BHM Spelled out: from Albany, New York, via Jet Route 37 transitioning to Jet Route 14 at Smyrna VORTAC (ENO) thence via Jet Route 14 to Birmingham, Alabama. 3. The route of flight may also be described by naming the reporting points or NAVAIDs over which the flight will pass, provided the points named are established for use at the altitude or flight level planned. EXAMPLE- BWI V44 SWANN V433 DQO Spelled out: from Baltimore-Washington International, via Victor 44 to Swann intersection, transitioning to Victor 433 at Swann, thence via Victor 433 to Dupont. 4. When the route of flight is defined by named reporting points, whether alone or in combination with airways or jet routes, and the navigational aids (VOR, VORTAC, TACAN, NDB) to be used for the flight are a combination of different types of aids, enough information should be included to clearly indicate the route requested. EXAMPLE- LAX J5 LKV J3 GEG YXC FL 330 J500 VLR J515 YWG Spelled out: from Los Angeles International via Jet Route_5 Lakeview, Jet Route 3 Spokane, direct Cranbrook, British Columbia VOR/DME, Flight Level_330 Jet Route 500 to Langruth, Manitoba VORTAC, Jet Route 515 to Winnepeg, Manitoba. 5. When filing IFR, it is to the pilot's advantage to file a preferred route. REFERENCE- Preferred IFR Routes are described and tabulated in the Airport/Facility Directory. 6. ATC may issue a SID or a STAR, as appropriate. REFERENCE- AIM, Instrument Departure Procedures (DP) - Obstacle Departure Procedures (ODP) and Standard Instrument Departures (SID), Paragraph 5-2-8. AIM, Standard Terminal Arrival (STAR), Area Navigation (RNAV) STAR, and Flight Management System Procedures (FMSP) for Arrivals, Paragraph 5-4-1. NOTE- Pilots not desiring a SID or STAR should so indicate in the remarks section of the flight plan as “no SID” or “no STAR.” c. Direct Flights 1. All or any portions of the route which will not be flown on the radials or courses of established airways or routes, such as direct route flights, must be defined by indicating the radio fixes over which the flight will pass. Fixes selected to define the route shall be those over which the position of the aircraft can be accurately determined. Such fixes automatically become compulsory reporting points for the flight, unless advised otherwise by ATC. Only those navigational aids established for use in a particular structure; i.e., in the low or high structures, may be used to define the en route phase of a direct flight within that altitude structure. 2. The azimuth feature of VOR aids and that azimuth and distance (DME) features of VORTAC and TACAN aids are assigned certain frequency protected areas of airspace which are intended for application to established airway and route use, and to provide guidance for planning flights outside of established airways or routes. These areas of airspace are expressed in terms of cylindrical service volumes of specified dimensions called “class limits” or “categories.” REFERENCE- AIM, Navigational Aid (NAVAID) Service Volumes, Paragraph 1-1-8. AIM 2/14/08 5-1-13 Preflight 3. An operational service volume has been established for each class in which adequate signal coverage and frequency protection can be assured. To facilitate use of VOR, VORTAC, or TACAN aids, consistent with their operational service volume limits, pilot use of such aids for defining a direct route of flight in controlled airspace should not exceed the following: (a) Operations above FL 450 - Use aids not more than 200 NM apart. These aids are depicted on enroute high altitude charts. (b) Operation off established routes from 18,000 feet MSL to FL 450 - Use aids not more than 260 NM apart. These aids are depicted on enroute high altitude charts.

使用道具 举报

Rank: 9Rank: 9Rank: 9

136#
发表于 2008-12-21 00:19:07 |只看该作者
(c) Operation off established airways below 18,000 feet MSL - Use aids not more than 80 NM apart. These aids are depicted on enroute low altitude charts. (d) Operation off established airways be- tween 14,500 feet MSL and 17,999 feet MSL in the conterminous U.S. - (H) facilities not more than 200_NM apart may be used. 4. Increasing use of self-contained airborne navigational systems which do not rely on the VOR/VORTAC/TACAN system has resulted in pilot requests for direct routes which exceed NAVAID service volume limits. These direct route requests will be approved only in a radar environment, with approval based on pilot responsibility for navigation on the authorized direct route. Radar flight following will be provided by ATC for ATC purposes. 5. At times, ATC will initiate a direct route in a radar environment which exceeds NAVAID service volume limits. In such cases ATC will provide radar monitoring and navigational assistance as necessary. 6. Airway or jet route numbers, appropriate to the stratum in which operation will be conducted, may also be included to describe portions of the route to be flown. EXAMPLE- MDW V262 BDF V10 BRL STJ SLN GCK Spelled out: from Chicago Midway Airport via Victor 262 to Bradford, Victor 10 to Burlington, Iowa, direct St._Joseph, Missouri, direct Salina, Kansas, direct Garden_City, Kansas. NOTE- When route of flight is described by radio fixes, the pilot will be expected to fly a direct course between the points named. 7. Pilots are reminded that they are responsible for adhering to obstruction clearance requirements on those segments of direct routes that are outside of controlled airspace. The MEAs and other altitudes shown on low altitude IFR enroute charts pertain to those route segments within controlled airspace, and those altitudes may not meet obstruction clearance criteria when operating off those routes. d. Area Navigation (RNAV) 1. Random RNAV routes can only be approved in a radar environment. Factors that will be considered by ATC in approving random RNAV routes include the capability to provide radar monitoring and compatibility with traffic volume and flow. ATC will radar monitor each flight, however, navigation on the random RNAV route is the responsibility of the pilot. 2. Pilots of aircraft equipped with approved area navigation equipment may file for RNAV routes throughout the National Airspace System and may be filed for in accordance with the following procedures. (a) File airport-to-airport flight plans. (b) File the appropriate RNAV capability certification suffix in the flight plan. (c) Plan the random route portion of the flight plan to begin and end over appropriate arrival and departure transition fixes or appropriate navigation aids for the altitude stratum within which the flight will be conducted. The use of normal preferred departure and arrival routes (DP/STAR), where established, is recommended. (d) File route structure transitions to and from the random route portion of the flight. (e) Define the random route by waypoints. File route description waypoints by using degree- distance fixes based on navigational aids which are appropriate for the altitude stratum. (f) File a minimum of one route description waypoint for each ARTCC through whose area the random route will be flown. These waypoints must be located within 200 NM of the preceding center's boundary. (g) File an additional route description waypoint for each turnpoint in the route. AIM 2/14/08 5-1-14 Preflight (h) Plan additional route description way- points as required to ensure accurate navigation via the filed route of flight. Navigation is the pilot's responsibility unless ATC assistance is requested. (i) Plan the route of flight so as to avoid prohibited and restricted airspace by 3 NM unless permission has been obtained to operate in that airspace and the appropriate ATC facilities are advised. NOTE- To be approved for use in the National Airspace System, RNAV equipment must meet the appropriate system availability, accuracy, and airworthiness standards. For additional guidance on equipment requirements see AC_20-130, Airworthiness Approval of Vertical Naviga- tion (VNAV) Systems for use in the U.S. NAS and Alaska, or AC 20-138, Airworthiness Approval of Global Positioning System (GPS) Navigation Equipment for Use as a VFR and IFR Supplemental Navigation System. For airborne navigation database, see AC 90-94, Guidelines for Using GPS Equipment for IFR En Route and Terminal Operations and for Nonprecision Instrument Approaches in the U.S. National Airspace System, Section 2. 3. Pilots of aircraft equipped with latitude/ longitude coordinate navigation capability, independent of VOR/TACAN references, may file for random RNAV routes at and above FL 390 within the conterminous U.S. using the following procedures. (a) File airport-to-airport flight plans prior to departure. (b) File the appropriate RNAV capability certification suffix in the flight plan. (c) Plan the random route portion of the flight to begin and end over published departure/arrival transition fixes or appropriate navigation aids for airports without published transition procedures. The use of preferred departure and arrival routes, such as DP and STAR where established, is recommended. (d) Plan the route of flight so as to avoid prohibited and restricted airspace by 3 NM unless permission has been obtained to operate in that airspace and the appropriate ATC facility is advised. (e) Define the route of flight after the departure fix, including each intermediate fix (turnpoint) and the arrival fix for the destination airport in terms of latitude/longitude coordinates plotted to the nearest minute or in terms of Navigation Reference System (NRS) waypoints. For latitude/ longitude filing the arrival fix must be identified by both the latitude/longitude coordinates and a fix identifier. EXAMPLE- MIA1 SRQ2 3407/106153 3407/11546 TNP4 LAX 5 1 Departure airport. 2 Departure fix. 3 Intermediate fix (turning point). 4 Arrival fix. 5 Destination airport. or ORD1 IOW2 KP49G3 KD34U4 KL16O5 OAL6 MOD27 SFO8 1 Departure airport. 2 Transition fix (pitch point). 3 Minneapolis ARTCC waypoint. 4 Denver ARTCC Waypoint. 5 Los Angeles ARTCC waypoint (catch point). 6 Transition fix. 7 Arrival. 8 Destination airport. (f) Record latitude/longitude coordinates by four figures describing latitude in degrees and minutes followed by a solidus and five figures describing longitude in degrees and minutes. (g) File at FL 390 or above for the random RNAV portion of the flight. (h) Fly all routes/route segments on Great Circle tracks. (i) Make any inflight requests for random RNAV clearances or route amendments to an en route ATC facility. e. Flight Plan Form- See FIG 5-1-2. f. Explanation of IFR Flight Plan Items. 1. Block 1. Check the type flight plan. Check both the VFR and IFR blocks if composite VFR/IFR. 2. Block 2. Enter your complete aircraft identification including the prefix “N” if applicable. 3. Block 3. Enter the designator for the aircraft, followed by a slant(/), and the transponder or DME equipment code letter; e.g., C-182/U. Heavy aircraft, add prefix “H” to aircraft type; example: H/DC10/U. Consult an FSS briefer for any unknown elements. AIM 2/14/08 5-1-15 Preflight FIG 5-1-2 FAA Flight Plan Form 7233-1 (8-82) U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION (FAA USE ONLY) PILOT BRIEFING VNR STOPOVER TIME STARTED INITIALS SPECIALIST 1. TYPE VFR IFR DVFR TYPE/ EQUIPMENT 3. AIRCRAFT SPECIAL 5. DEPARTURE POINT 6. DEPARTURE TIME PROPOSED (Z) ACTUAL (Z) 7. ALTITUDE CRUISING 8. ROUTE OF FLIGHT KTS 9. Name city) DESTINATION (of airport and 10. EST. TIME ENROUTE HOURS HOURS MINUTES MINUTES 11. REMARKS 12. FUEL ON BOARD AIRPORT(13. ALTERNATE S) 14. PILOT'S NAME, ADDRESS & TELEPHONE NUMBER & AIRCRAFT HOME BASE 15. NUMBER ABOARD 17. DESTINATION CONTACT/TELEPHONE (OPTIONAL) AIRCRAFT 16. COLOR OF FAA Form 7233-1 (8-82) VFR PLAN WITH CLOSE FLIGHT _________________ FSS ON ARRIVAL FLIGHT PLAN CIVIL AIRCRAFT PILOTS, FAR 91 requires you file an IFR flight plan to operate under instrument flight rules in controlled airspace. Failure to file could result in a civil penalty not to exceed 1,000 for each violation (Section 901 of the Federal Aviation Act of 1958, as amended). Filing of a VFR flight plan is recommended as a good operating practice. See also Part 99 for requirements concerning DVFR flight plans. 2. AIRCRAFT IDENTIFICATION 4. TRUE AIRSPEED 4. Block 4. Enter your computed true airspeed (TAS). NOTE- If the average TAS changes plus or minus 5 percent or 10_knots, whichever is greater, advise ATC. 5. Block 5. Enter the departure airport identifi- er code (or the name if the identifier is unknown). NOTE- Use of identifier codes will expedite the processing of your flight plan. 6. Block 6. Enter the proposed departure time in Coordinated Universal Time (UTC) (Z). If airborne, specify the actual or proposed departure time as appropriate. 7. Block 7. Enter the requested en route altitude or flight level. NOTE- Enter only the initial requested altitude in this block. When more than one IFR altitude or flight level is desired along the route of flight, it is best to make a subsequent request direct to the controller. 8. Block 8. Define the route of flight by using NAVAID identifier codes (or names if the code is unknown), airways, jet routes, and waypoints (for RNAV). NOTE- Use NAVAIDs or waypoints to define direct routes and radials/bearings to define other unpublished routes. 9. Block 9. Enter the destination airport identifier code (or name if the identifier is unknown). 10. Block 10. Enter your estimated time en route based on latest forecast winds. AIM 2/14/08 5-1-16 Preflight 11. Block 11. Enter only those remarks perti- nent to ATC or to the clarification of other flight plan information, such as the appropriate radiotelephony (call sign) associated with the designator filed in Block_2. Items of a personal nature are not accepted. Do not assume that remarks will be automatically transmitted to every controller. Specific ATC or en_route requests should be made directly to the appropriate controller. NOTE“DVRSN” should be placed in Block 11 only if the pilot/company is requesting priority handling to their original destination from ATC as a result of a diversion as defined in the Pilot/Controller Glossary. 12. Block 12. Specify the fuel on board, computed from the departure point. 13. Block 13. Specify an alternate airport if desired or required, but do not include routing to the alternate airport. 14. Block 14. Enter the complete name, address, and telephone number of pilot-in-command, or in the case of a formation flight, the formation commander. Enter sufficient information to identify home base, airport, or operator. NOTE- This information would be essential in the event of search and rescue operation. 15. Block 15. Enter the total number of persons on board including crew. 16. Block 16. Enter the predominant colors. NOTE- Close IFR flight plans with tower, approach control, or ARTCC, or if unable, with FSS. When landing at an airport with a functioning control tower, IFR flight plans are automatically canceled. g. The information transmitted to the ARTCC for IFR flight plans will consist of only flight plan blocks_2, 3, 4, 5, 6, 7, 8, 9, 10, and 11. h. A description of the International Flight Plan Form is contained in the International Flight Information Manual (IFIM). 5-1-9. IFR Operations to High Altitude Destinations a. Pilots planning IFR flights to airports located in mountainous terrain are cautioned to consider the necessity for an alternate airport even when the forecast weather conditions would technically relieve them from the requirement to file one. REFERENCE14 CFR Section 91.167. AIM, Tower En Route Control (TEC), Paragraph 4-1-18. b. The FAA has identified three possible situations where the failure to plan for an alternate airport when flying IFR to such a destination airport could result in a critical situation if the weather is less than forecast and sufficient fuel is not available to proceed to a suitable airport. 1. An IFR flight to an airport where the Minimum Descent Altitudes (MDAs) or landing visibility minimums for all instrument approaches are higher than the forecast weather minimums specified in 14 CFR Section 91.167(b). For example, there are 3 high altitude airports in the U.S. with approved instrument approach procedures where all of the MDAs are greater than 2,000 feet and/or the landing visibility minimums are greater than 3 miles (Bishop, California; South Lake Tahoe, California; and Aspen-Pitkin Co./Sardy Field, Colorado). In the case of these airports, it is possible for a pilot to elect, on the basis of forecasts, not to carry sufficient fuel to get to an alternate when the ceiling and/or visibility is actually lower than that necessary to complete the approach. 2. A small number of other airports in mountainous terrain have MDAs which are slightly (100 to 300 feet) below 2,000 feet AGL. In situations where there is an option as to whether to plan for an alternate, pilots should bear in mind that just a slight worsening of the weather conditions from those forecast could place the airport below the published IFR landing minimums. 3. An IFR flight to an airport which requires special equipment; i.e., DME, glide slope, etc., in order to make the available approaches to the lowest minimums. Pilots should be aware that all other minimums on the approach charts may require weather conditions better than those specified in 14_CFR Section_91.167(b). An inflight equipment malfunction could result in the inability to comply with the published approach procedures or, again, in the position of having the airport below the published IFR landing minimums for all remaining instrument approach alternatives. AIM 2/14/08 5-1-17 Preflight 5-1-10. Flights Outside the U.S. and U.S. Territories a. When conducting flights, particularly extended flights, outside the U.S. and its territories, full account should be taken of the amount and quality of air navigation services available in the airspace to be traversed. Every effort should be made to secure information on the location and range of navigational aids, availability of communications and meteoro- logical services, the provision of air traffic services, including alerting service, and the existence of search and rescue services. b. Pilots should remember that there is a need to continuously guard the VHF emergency frequency 121.5 MHz when on long over-water flights, except when communications on other VHF channels, equipment limitations, or cockpit duties prevent simultaneous guarding of two channels. Guarding of 121.5 MHz is particularly critical when operating in proximity to Flight Information Region (FIR) boundaries, for example, operations on Route R220 between Anchorage and Tokyo, since it serves to facilitate communications with regard to aircraft which may experience in-flight emergencies, com- munications, or navigational difficulties. REFERENCE- ICAO Annex 10, Vol II, Paras 5.2.2.1.1.1 and 5.2.2.1.1.2. c. The filing of a flight plan, always good practice, takes on added significance for extended flights outside U.S. airspace and is, in fact, usually required by the laws of the countries being visited or overflown. It is also particularly important in the case of such flights that pilots leave a complete itinerary and schedule of the flight with someone directly concerned and keep that person advised of the flight's progress. If serious doubt arises as to the safety of the flight, that person should first contact the appropriate FSS. Round Robin Flight Plans to Mexico are not accepted. d. All pilots should review the foreign airspace and entry restrictions published in the IFIM during the flight planning process. Foreign airspace penetration without official authorization can involve both danger to the aircraft and the imposition of severe penalties and inconvenience to both passen- gers and crew. A flight plan on file with ATC authorities does not necessarily constitute the prior permission required by certain other authorities. The possibility of fatal consequences cannot be ignored in some areas of the world. e. Current NOTAMs for foreign locations must also be reviewed. The publication Notices to Airmen, Domestic/International, published biweekly, con- tains considerable information pertinent to foreign flight. Current foreign NOTAMs are also available from the U.S. International NOTAM Office in Washington, D.C., through any local FSS. f. When customs notification is required, it is the responsibility of the pilot to arrange for customs notification in a timely manner. The following guidelines are applicable: 1. When customs notification is required on flights to Canada and Mexico and a predeparture flight plan cannot be filed or an advise customs message (ADCUS) cannot be included in a predeparture flight plan, call the nearest en route domestic or International FSS as soon as radio communication can be established and file a VFR or DVFR flight plan, as required, and include as the last item the advise customs information. The station with which such a flight plan is filed will forward it to the appropriate FSS who will notify the customs office responsible for the destination airport. 2. If the pilot fails to include ADCUS in the radioed flight plan, it will be assumed that other arrangements have been made and FAA will not advise customs. 3. The FAA assumes no responsibility for any delays in advising customs if the flight plan is given too late for delivery to customs before arrival of the aircraft. It is still the pilot's responsibility to give timely notice even though a flight plan is given to FAA. 4. Air Commerce Regulations of the Treasury Department's Customs Service require all private aircraft arriving in the U.S. via: (a) The U.S./Mexican border or the Pacific Coast from a foreign place in the Western Hemisphere south of 33 degrees north latitude and between 97 degrees and 120 degrees west longitude; or AIM 2/14/08 5-1-18 Preflight (b) The Gulf of Mexico and Atlantic Coasts from a foreign place in the Western Hemisphere south of 30 degrees north latitude, shall furnish a notice of arrival to the Customs service at the nearest designated airport. This notice may be furnished directly to Customs by: (1) Radio through the appropriate FAA Flight Service Station. (2) Normal FAA flight plan notification procedures (a flight plan filed in Mexico does not meet this requirement due to unreliable relay of data); or (3) Directly to the district Director of Customs or other Customs officer at place of first intended landing but must be furnished at least 1 hour prior to crossing the U.S./Mexican border or the U.S. coastline. (c) This notice will be valid as long as actual arrival is within 15 minutes of the original ETA, otherwise a new notice must be given to Customs. Notices will be accepted up to 23 hours in advance. Unless an exemption has been granted by Customs, private aircraft are required to make first landing in the U.S. at one of the following designated airports nearest to the point of border of coastline crossing: Designated Airports ARIZONA Bisbee Douglas Intl Airport Douglas Municipal Airport Nogales Intl Airport Tucson Intl Airport Yuma MCAS-Yuma Intl Airport CALIFORNIA Calexico Intl Airport Brown Field Municipal Airport (San Diego) FLORIDA Fort Lauderdale Executive Airport Fort Lauderdale/Hollywood Intl Airport Key West Intl Airport (Miami Intl Airport) Opa Locka Airport (Miami) Kendall-Tamiami Executive Airport (Miami) St. Lucie County Intl Airport (Fort Pierce) Tampa Intl Airport Palm Beach Intl Airport (West Palm Beach) LOUISANA New Orleans Intl Airport (Moisant Field) New Orleans Lakefront Airport NEW MEXICO Las Cruces Intl Airport NORTH CAROLINA New Hanover Intl Airport (Wilmington) TEXAS Brownsville/South Padre Island Intl Airport Corpus Christi Intl Airport Del Rio Intl Airport Eagle Pass Municipal Airport El Paso Intl Airport William P. Hobby Airport (Houston) Laredo Intl Airport McAllen Miller Intl Airport Presidio Lely Intl Airport 5-1-11. Change in Flight Plan In addition to altitude or flight level, destination and/or route changes, increasing or decreasing the speed of an aircraft constitutes a change in a flight plan. Therefore, at any time the average true airspeed at cruising altitude between reporting points varies or is expected to vary from that given in the flight plan by plus or minus 5 percent, or 10 knots, whichever is greater, ATC should be advised. 5-1-12. Change in Proposed Departure Time a. To prevent computer saturation in the en route environment, parameters have been established to delete proposed departure flight plans which have not been activated. Most centers have this parameter set so as to delete these flight plans a minimum of 1 hour after the proposed departure time. To ensure that a flight plan remains active, pilots whose actual departure time will be delayed 1 hour or more beyond their filed departure time, are requested to notify ATC of their departure time. b. Due to traffic saturation, control personnel frequently will be unable to accept these revisions via radio. It is recommended that you forward these revisions to the nearest FSS. AIM 2/14/08 5-1-19 Preflight

使用道具 举报

Rank: 9Rank: 9Rank: 9

137#
发表于 2008-12-21 00:19:20 |只看该作者
5-1-13. Closing VFR/DVFR Flight Plans A pilot is responsible for ensuring that his/her VFR or DVFR flight plan is canceled. You should close your flight plan with the nearest FSS, or if one is not available, you may request any ATC facility to relay your cancellation to the FSS. Control towers do not automatically close VFR or DVFR flight plans since they do not know if a particular VFR aircraft is on a flight plan. If you fail to report or cancel your flight plan within 1 /2 hour after your ETA, search and rescue procedures are started. REFERENCE14 CFR Section 91.153. 14 CFR Section 91.169.

使用道具 举报

Rank: 9Rank: 9Rank: 9

138#
发表于 2008-12-21 00:19:27 |只看该作者
5-1-14. Canceling IFR Flight Plan a. 14 CFR Sections 91.153 and 91.169 include the statement “When a flight plan has been activated, the pilot-in-command, upon canceling or completing the flight under the flight plan, shall notify an FAA Flight Service Station or ATC facility.” b. An IFR flight plan may be canceled at any time the flight is operating in VFR conditions outside Class A airspace by pilots stating “CANCEL MY IFR FLIGHT PLAN” to the controller or air/ground station with which they are communicating. Immediately after canceling an IFR flight plan, a pilot should take the necessary action to change to the appropriate air/ground frequency, VFR radar beacon code and VFR altitude or flight level.

使用道具 举报

Rank: 9Rank: 9Rank: 9

139#
发表于 2008-12-21 00:19:38 |只看该作者
c. ATC separation and information services will be_discontinued, including radar services (where applicable). Consequently, if the canceling flight desires VFR radar advisory service, the pilot must specifically request it. NOTE- Pilots must be aware that other procedures may be applicable to a flight that cancels an IFR flight plan within an area where a special program, such as a designated TRSA, Class C airspace, or Class B airspace, has been established. d. If a DVFR flight plan requirement exists, the pilot is responsible for filing this flight plan to replace the canceled IFR flight plan. If a subsequent IFR operation becomes necessary, a new IFR flight plan must be filed and an ATC clearance obtained before operating in IFR conditions. e. If operating on an IFR flight plan to an airport with a functioning control tower, the flight plan is automatically closed upon landing. f. If operating on an IFR flight plan to an airport where there is no functioning control tower, the pilot must initiate cancellation of the IFR flight plan. This can be done after landing if there is a functioning FSS or other means of direct communications with ATC. In the event there is no FSS and/or air/ground communications with ATC is not possible below a certain altitude, the pilot should, weather conditions permitting, cancel the IFR flight plan while still airborne and able to communicate with ATC by radio. This will not only save the time and expense of canceling the flight plan by telephone but will quickly release the airspace for use by other aircraft.

使用道具 举报

Rank: 9Rank: 9Rank: 9

140#
发表于 2008-12-21 00:19:45 |只看该作者
5-1-15. RNAV and RNP Operations a. During the pre-flight planning phase the availability of the navigation infrastructure required for the intended operation, including any non-RNAV contingencies, must be confirmed for the period of intended operation. Availability of the onboard navigation equipment necessary for the route to be flown must be confirmed. b. If a pilot determines a specified RNP level cannot be achieved, revise the route or delay the operation until appropriate RNP level can be ensured. c. The onboard navigation database must be appropriate for the region of intended operation and must include the navigation aids, waypoints, and coded terminal airspace procedures for the departure, arrival and alternate airfields.

使用道具 举报

您需要登录后才可以回帖 登录 | 注册


Archiver|航空论坛 ( 渝ICP备10008336号 )

GMT+8, 2024-11-24 03:40 , Processed in 0.035002 second(s), 8 queries .

Powered by Discuz! X2

© 2001-2011 MinHang.CC.

回顶部